XYZ Printing Nobel Superfine Bedienungsanleitung
-1-
(US)XYZprinting, Inc.
• Website: http://us.xyzprinting.com
• Online Customer Service Desk: http://support.xyzprinting.com/us_en/Help/ticket/home
↓↓
USB Wire
Port
Power Jack
Product Overview and Accessories
Quick Start Guide Please read this guide carefully for steps of unpacking, setting up, printing, post
processing and printer maintenance to ensure your perfect 3D printing experience!
Unpacking and Setting Up
Unpack the carton, remove all protective
material and take the printer out of the
package.
●Power On
●Side View
●Back View
■Side View
■Back View
●Front View
Printing
Connect the printer to a power source and
turn on the printer.
Shake the resin bottle for about 10 seconds.
Assemble the nozzle cap and the inner tube,
and replace the original bottle cap with the
assembled one.
Install the filling tubes( Attach the black tube to
the thick nozzle firstly. Then attach the
transparent tube to the thin nozzle and push
all tubes down.)
●Raise the Platform
●Install the Resin Bottle
Select "UTILITIES" > "MOVE PLATFORM"
> "TO TOP" > "YES" to raise the platform.
Remove the protective materials under the
platform.
Put the bottle into the bottle slot.
※Please retain all original packaging material. If you
need warranty service, please ship your product with
the original packaging. Shipping without the original
packaging material may cause product damage
during the shipment and may result in service fees
for which you will be responsible.
Power Switch
←Platform
↑
Tank Slot
LCM→
←Operation
Panel
USB Disk
Port→
Filling Tube→
Install the printing software XYZware_Nobel
from the bundled USB flash drive.
※Apply printer firmware and XYZware_Nobel
updates when prompted by the software for stable
printing performance.
●Install Printing Software
The Nobel Superfine is shipped with the below parts and accessories. After
unpacking, please check if any damage on printer and accessories.
Please contact the support for any losing or defective parts and accessories.
■USB Cable
■USB Flash Disk
■Rinse Basket
■Scraper
■Gloves
■Starter
Resin
■Nozzle Cap
■Inner
Tube
■Power Cable
■Power Adapter
Resin Bottle
Slot→
■Quick Start Guide■Warranty Card
To fill the resin tank before sending the
printing task, please select "UTILITIES" >
"REFILL RESIN" on the printer screen. And
press and hold the UP key to infuse resin into
the tank. Release the UP key until the resin
reaching the "Max" mark(The resin capacity to
MAX mark on the resin tank is about 90g), to
avoid resin effluence from the resin tank.
Note
Hint
Before changing the resin bottle, remove the
transparent tube firstly then the black tube.
ENGLISH
↓
Up
-2-
(EU) XYZprinting Netherlands B.V.
• Website: http://eu.xyzprinting.com • Online Customer Service Desk: http://support.xyzprinting.com/eu_en/Help/ticket/home
(Global) XYZprinting, Inc. • Website: http://global.xyzprinting.com/
Import 3D objects to XYZware_Nobel, add
proper supports, press "Print" to set up the
printing parameters. Once the file is sliced, it
will be sent to the printer.
Remove and Clean the Print
Turn the printing platform knob counter-clock-
wise and then pull the platform out.
Remove the printed object from
the platform with a scraper.
Pour alcohol into the rinse basket, and shake
the print for 5 minutes, wash the uncured
resin on the print's surface and take it out.
Install the printing platform back to printer.
Import the 3D model into XYZware_Nobel,
select "EXPORT" to save in USB flash disk as
".3wn" file format.
Plug the flash drive into the USB port on the
front of the printer.
Select "PRINT FROM USB" on control panel
to open the model list, select the file to print.
Import 3D objects to XYZware_Nobel, add
proper supports, press "Print" to set up the
printing parameters. Once the file is sliced, it
will be sent to the printer via WIFI Connection.
Important Notes
▲Please place and operate the printer in a well
ventilated area.
▲Please read the guide carefully before using the
printer.
▲For safety concerns, wear safety goggles before
operating the printer.
▲Do not let children operate this device without adult
supervision.
▲Please ensure that the recommended operating
conditions are adhered to. (Operating
temperature 20-30°C (68-86°F) / humidity 40 ~ 60%
RH; If a different operating temperature is printed on
the label on the resin bottle, please adhere to
recommended conditions on the label.)
▲For the best printing quality, resin should be used
up within 3 months after purchasing and within 1
month of opening. Resin should preferably be stored
at temperatures between 10-32°C (50-89.6°F),
localized heat sources (i.e., drum or band heaters),
oxidizing conditions, freezing conditions, direct
sunlight, ultraviolet radiation, inert gas blanketing.
▲If the printer is unused for more than a week, resin
pigments may settle at the bottom of the bottle or the
tank. Shake / stir well before using.
▲The resin tank is consumable. It should be
replaced when the bottom is damaged or gets dent to
ensure the printing quality.
▲It is suggested to use isolated resin tank while
different color resin is going to be used to ensure
printing quality.
●Printing via USB Flash Disk
●Printing via WIFI Connection
■Enable WIFI connection
Select "SETTING" > "WIFI" > "CONNECT
NEW", and wait for available wireless network
scanned by the printer.
Choose the WIFI network which your PC
connects to from the network scan list, press
[OK] and select "ENRER PASSWORD" to go
to password input mode.
Connect the printer to your PC with the USB
cable.
●Printing via PC Client
●Home Key: Switch
input mode
●Up and Down keys:
Select numerals,
alphabets, or symbols.
●Left and Right keys:
Moves to the previous or
next digit.
Up
Down
Right
HOME
Left
Tutorial
1. Always remove the platform before removing the
resin tank to avoid dripping leftover material on
printer surface.
2. Rinse with 75% alcohol or higher concentration.
Washing with alcohol of higher concentration will
result in higher cleaning efficiency. Alcohol is not
supplied with the printer.
3. The cleanup time of print depends on of the
complexity, structural fineness of the print and other
factors, it is recommended not to rinse more than 5
minutes to ensure that the integrity of the print.
Extend proper cleanup time for if necessary.
4. Always ware gloves before touching uncured resin
or cleaning prints.
5. Remove any residue on the platform or the resin
tank before next print to ensure the printing quality.
Note
Hint
Enter password with the control panel and
press[OK] to activate the WIFI function.
4 input modes are available, including capital
English letters, lowercase English letters,
Arabic numerals and special symbols. When
in the password input mode, the keys function
as illustrated below:
Once the WIFI connection is setup correctly
and kept connected on the printer, you can
start printing via WIFI connection from the
next step.
Run XYZware_Nobel on the PC, press
"Printer Monitor" in right lower corner. In the
Printer Monitor list, select the desired printer
from the network printer list.
PASSWORD : [A B C]
XXXXXXXXX_
[HOME] KEY MODE
[OK] TO FINISH
<--- Current input
mode
▲For complete instructions and troubleshooting,
please refer to the product manual. You can find the
product manual in the bundled USB flash drive or
download the latest version from:
http://support.xyzprinting.com/
us_en/Help/download
▲For tutorial videos, please go to:
http://support.xyzprinting.com/
us_en/Help/tutorial
■Enter the WIFI Password
■Print Wireless from PC
Andere Handbücher für Nobel Superfine
1
Dieses Handbuch passt für folgende Modelle
1
Andere XYZ Printing 3D-Drucker Handbücher
XYZ Printing
XYZ Printing da Vinci Jr.1.0 Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci 1.0 Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci 1.1 Plus Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci 1.0 Pro 3in1 Bedienungsanleitung
XYZ Printing
XYZ Printing 3C10A Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci Jr.1.0 Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci 1.0 Pro Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci Jr.1.0 Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci Jr. 1.0 Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci 1.0 Bedienungsanleitung
XYZ Printing
XYZ Printing PartPro200 xTCS Bedienungsanleitung
XYZ Printing
XYZ Printing ds Vinci Color Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci nano Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci 2.0 Duo Bedienungsanleitung
XYZ Printing
XYZ Printing PartPro300 xT Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci Jr. WiFi Pro Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci Jr.1.0A Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci Jr 1.0 Pro Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci 1.0 Pro Bedienungsanleitung
XYZ Printing
XYZ Printing da Vinci Jr.1.0w Bedienungsanleitung
