ZALMAN RESERATOR2 Kurzanleitung
RESERATOR 2
English Version
Visit our website (www.zalman.co.kr) and watch the Reserator 2 installation
video for an installation overview.
※Please read this manual thoroughly before installation.
※The s ecifications of this roduct and its com onents may change without rior notice to im rove the erformance thereof.
www.zalman.co.kr www.zalmanusa.com
RESERATOR 2
2
※
The specifications of any product may change without prior notice to improve performance.
1. Make sure that the ower source’s out ut voltage and frequency are com atible with
the ower in ut requirements of the water um before installing (in ut voltage and
frequency of the water um are shown on the box).
2. Do not lace in dusty or humid conditions, under direct sunlight, or near a heat source
such as a room heater.
3. Do not dro or subject it to excessive force.
4. CPU socket com atibility must be checked.
5. Familiarize yourself with this manual.
6. Do not mix any contaminant with the coolant when filling, for it may cause roduct failure.
7. Check for leaks on Water Blocks before installation.
Installation Notes
1. Reserator 2 simultaneously o erates with the PC. The ower must first be su lied to
the AC ower cable before turning on the PC because it uses an AC um .
2. Place the Reserator 2 and the PC body at the same location for use.
3. If the coolant isn’t circulating ro erly, or if the um flux becomes too low, then the
red blinkers will flash as well as warning sound. In this case, turn the PC OFF immediately.
4. Do not lace any objects on the roduct.
5. Install on a flat surface with no vibration or slant, and do not tilt or lay horizontally.
6. Use distilled water with the coolant, regularly check the amount of coolant, and re lenish
as needed (must be re lenished every year).
7. If a leak is found, turn off the system immediately, and contact the lace of urchase
or ZALMAN.
8. If the system will not be used for an extended eriod of time, then turn the Water
Pum OFF.
9. When moving the system, se arate the Reserator from the PC case before moving.
10. Do not let any air bubbles form inside the Water Block and the tubes during o eration.
11. Always make sure that the Water Pum is functioning ro erly.
12. If the ower su ly cord is damaged, it must be re laced by the manufacturer, its
service agent, or a similarly qualified erson in order to avoid a hazard.
Operational Notes
Installation and Operational Notes
English
RESERATOR 2
※
The specifications of any product may change without prior notice to improve performance.
Reserator 2 incor orates Zalman’s HCET(High Ca acity Extrusion Technique)
technology, high efficiency cooling technology, and o timal heat dissi ation design for
exce tional cooling erformance even through natural convection cooling.
The Reserator 2 is a noiseless and fanless water cooling system that incor orates a and
Flow Indicator in the front section, a high efficiency heatsink in the middle section, and a
water tank and water um in the back section which allows easy installation and use.
The anodized roduct and the rovided coolant revents corrosion. The new CPU
Water Block (ZM-WB4 Gold), VGA Water Block (ZM-GWB3), and the o tional
Northbridge Water Block (ZM-NWB1) and VGA RAM Water Block (ZM-RWB1) enable
the setu of a com lete Water Cooling System.
Installation and Operational Notes
1. Features
2. S ecifications
5
3. Installation Overview
6
4. Standard Com onents and O tional Com onents
7
5. Installation Guide
9
6. External Water Pum Installation
15
7. Ex loded View
16
8. Zalman Noise Prevention System
17
Table of Contents
1. Features
RESERATOR 2
4
※
The specifications of any product may change without prior notice to improve performance.
1. 1 Reserator (Reservoir + Radiator + Water Pump)
“Reserator” is a com ound word derived from ‘Reservoir’ and
‘Radiator’- it acts as a reservoir while radiating heat. This roduct
works well with natural convection and integrates a Water Pum
inside for convenience. It incor orates a flux observation/warning
device as well as the Flow Indicator in the front, which further allows
a safe and convenient use of the roduct.
1. 2 CPU Water Block (ZM-WB Gold)
The CPU Water Block incor orates a ure co er base for excellent
heat transfer, and is gold lating to revent corrosion. It su orts
Pentium 4 Socket 775/478 CPU and AMD Socket 754/939/940 CPU,
and is designed to be light weight and easy to install.
1. 3 VGA Water Block (ZM-GWB3)
The VGA Water Block incor orates a light weight ure aluminum base
for high cooling erformance, and is anodized and coated to revent
corrosion. It also incor orates revolving fittings that rovide freedom in
direction when connecting them with the tubes, which further allows
sim le installation.
1. Northbridge Water Block (ZM-NWB1, Optional)
This anodized, ure aluminum block is built for high erformance cooling, and is
designed for com atibility with a wide variety of Northbridge chi sets.
1. 5 VGA RAM Water Block (ZM-RWB1, Optional)
This anodized, ure aluminum RAM Water Block is built for high
erformance cooling, and is com atible with GeForce 7800/7900 and ATI
X1800/X1900 in need of VGA RAM cooling. It rovides easy installation.
1. 6 Anti-Corrosion Coolant (ZM-G300)
This coolant contains a high quality anti-corrosion agent for various
materials including co er, aluminum, lastic, that revents corrosion for
long term o eration.
1. 7 Flow Indicator
This com onent is connected with the circulation tube for checking the
circulation of the coolant. When the coolant is actively circulating, its
im eller rotates and the blue LED is brightly lit, roviding easy indication
of the circulation status.
1. 8 Quick Coupling
The Fittings incor orate valves that revent leaks when disconnecting
the PVC Tubes allowing quick, convenient se aration and reassembly of
the Reserator for trans ort and coolant re lacement.
5
English
RESERATOR 2
※
The specifications of any product may change without prior notice to improve performance.
2. 1 Reserator (Reservoir + Radiator+Water pump)
1) Dissi ation Area : 1.5㎡
2) Weight : 7 kg
3) Dimensions : 76(L) x 436(W) x 369(H) mm
4) Material : Anodized Pure Aluminum
5) Max Coolant Ca acity : 1.25ℓ
6) Integrated Water Pum : 5 W, Qmax 300 ℓ/h
(A ty e : 230V-50Hz, B ty e : 115V-60Hz, C ty e : 220V-60Hz, D ty e : 100V-60Hz)
7) Maximum Lift : 0.5 m
2. 2 CPU Water Block (ZM-WB Gold)
1) Weight : 135 g
2) Material : Polycarbonate Cover, Gold Plated Pure Co er Base
3) Dimensions : 63(L) x 63(W) x 16.5(H) mm
4) Com atibility : Intel Pentium 4 (Socket 775/478), AMD Sem ron / AMD64 (Athlon
64/Athlon 64 FX/O teron) (Socket 754/939/940)
2. 3 VGA Water Block (ZM-GWB3)
1) Weight : 100 g
2) Material : Anodized Pure Aluminum
3) Dimensions : 60.4(L) x 60.4(W) x 30(H) mm
4) Com atibility : Gra hics cards with heatsink mounting holes
2. Northbridge Water Block (ZM-NWB1, Optional)
1) Weight : 48 g
2) Material : Anodized Pure Aluminum
3) Dimensions : 43(L) x 43(W) x 30(H) mm
2. 5 VGA RAM Water Block (ZM-RWB1, Optional)
1) Weight : 120 g
2) Material : Anodized Pure Aluminum
3) Dimensions : 19(L) x 122(W) x 12(H) mm
2. 6 Anti-Corrosion Coolant(ZM-G300)
1) Material : Pro ylene Glycol & Anti-Corrosion Agent
2) Volume : 250
mℓ
3) Freezing Point : -9 ℃
4) Exchange Cycle : 1 year
2. Specifications
RESERATOR 2
6
※
The specifications of any product may change without prior notice to improve performance.
. Installation Overview
DC Cable
Power Supply
4-Pin Connecter
CPU
Water
Block
VGA
Water
Block
I/O Bracket
Quick Coupling
AC Cable
7
English
RESERATOR 2
※
The specifications of any product may change without prior notice to improve performance.
4. Components
. 1 Reserator 2 - 1 UNIT
. 2
CPU Water Block (ZM-WB Gold) 1SET
Please refer to the se arately rovided
manual for the ZM-WB4 Gold.
.
3 VGA Water Block (ZM-GWB3) 1SET
Please refer to the se arately rovided
manual for the ZM-GWB3.
. 6 Coolant (ZM-G300) 1EA
. 7 PVC Tube m
. 8 I/O Bracket 1EA
. 9
Degassing Tube 1EA
. 10 Tube Clamp 2EA
. 11 Bolt- EA
. Support- 2EA
. 5 Jump Cable 1EA
. 12 User’s Manual
RESERATOR 2
8
※
The specifications of any product may change without prior notice to improve performance.
Optional Components
●●
Power Supply
By im lementing heat-sensor circuitry that controls the
fan’s s eed in relation to the tem erature within the
ower su ly, noise is significantly reduced, making this
com onent suitable for noiseless systems.
●●
Northbridge Water Block (ZM-NWB1)
This anodized, ure aluminum block is built for high
erformance cooling, and is designed for Motherboard
com atibility with a wide variety of northbridge chi sets.
●●
VGA RAM Water Block (ZM-RWB1)
This VGA RAM Water Block is com atible with GeForce
7800/7900 and ATI X1800/X1900 in need of VGA RAM
cooling.
●●
Heatpipe HDD Cooler
This com onent cools the heat generated from the hard
disk drive and reduces the vibration that is assed onto
the com uter’s enclosure.
●●
PVC Tube
If the standard PVC tube is found to be short or you need
to use the tube on another system, additional tubes can
be urchased se arately (12 x 8 mm).
9
English
RESERATOR 2
※
The specifications of any product may change without prior notice to improve performance.
5. Installation Guide
5. 1 Determine the Placement of the
Reserator
The Reserator’s lacement should be determined
in relation to the osition of the PC.
Place it u right next to or slightly above the PC.
Note that if the Reserator is laced lower than
the PC, the PVC tube’s internal air ressure
may revent ro er initial o eration.
5. 2 Install the Supports
Install the enclosed Su orts on to the Tab
located on the bottom of the Reserator with
the use of Bolts.
5. 3 Fill the Coolant
1) Take off the Reserator Cover after unscrewing
its Bolts.
2) Fill with the rovided coolant (ZM-G300,
250㎖) and one liter of distilled water.
Note 1) Fill in a roximately 50% to avoid
overflow within the Reservoir, and
must refill because the water level
decreases once the coolant begins to
circulate after erfectly releasing the
air within the Reservoir.
Note 2) The rovided coolant is a concentrate,
and must be mixed down with distilled
water in the ratio of 1:4.
Note 3) Read the warning label on the coolant
before use.
Note ) Kee this roduct and its associated
system away from children.
((OO))((OO))
((XX))((XX))
Bolt
Reservoir Cover
Reservoir
Distilled Water
G300
RESERATOR 2
10
※
The specifications of any product may change without prior notice to improve performance.
5. Reserator’s Coolant Circulation
1) The ur ose of connecting the Jum Cable of the ower su ly’s main connector
(20P/24P) is to receive direct current (12V) needed for the test and leakage ins ection.
2) Turn off all ower of the PC and switch the Power Su ly's ON/OFF button to OFF, connect
the enclosed Degassing Tube to the Reserator’s IN-OUT, and rovide ower to the AC cable.
3) Disconnect the ower su ly's main connector (20P/24P) and the CPU 4-Pin connector
from the motherboard, and connect the green wire terminal with the black wire terminal
with the use of Jum Cable.
4) Connect the Reserator’s DC cable connector to the ower su ly’s 4-Pin connector,
and rovide ower to the PC by switching the ower su ly's ON/OFF button to ON.
5) Blue LED will light u and the im eller located inside the Flow Indicator of the Reserator’s
front anel will begin to rotate when the ower is su lied. (At this moment, let the
coolant circulate for approximately 30 seconds, then cut off the direct current and
wait for the impeller to stop. Once the impeller has come to a complete halt, you
must restart it in order to entirely eliminate the internal air. )
6) If the coolant is not circulating well due to internal air ressure during initial o eration,
then tilt the Reserator by a roximately 70。and re eatedly turn the Reserator ON/OFF
with the Light/Reset button to com letely release internal air tra ed within the Reserator
body (must ress the Reset button for longer than 5 seconds).
7) If the coolant is circulating ro erly, then turn of the ower of the Power Su ly, disconnect
the Degassing Tube, and disassemble the Quick Cou ling Insert.
Note 1) Pay attention so that the coolant inside the Reservoir does not s ill.
Note 2) Check the state of air release with the tube. If air is com letely released, then turn
off the Power Su ly and begin installing the water blocks.
Note 3) During coolant circulation, if the Flow Indicator fails to effectively sense the flux,
then the alarm will go off and the red LED will flicker. Press onto the Light/Reset
button for 5 seconds to reboot.
Quick Coupling
Insert
Degassing Tube
4-Pin Connecter
DC Cable Connecter
Main
Connecter
Motherboard
Power Connecter
Black Wire
Green Wire
Jump Cable
Light/Reset Button
Andere ZALMAN Computerhardware Handbücher
ZALMAN
ZALMAN CNPS8000B Bedienungsanleitung
ZALMAN
ZALMAN S5 Bedienungsanleitung
ZALMAN
ZALMAN CNPS20LQ Bedienungsanleitung
ZALMAN
ZALMAN ZM-WB3 Gold Bedienungsanleitung
ZALMAN
ZALMAN ZM-WB5 Plus Bedienungsanleitung
ZALMAN
ZALMAN RESERATOR1 V2 Kurzanleitung
ZALMAN
ZALMAN CNPS6000-Al Bedienungsanleitung
ZALMAN
ZALMAN CNPS7000C-Cu/AICu Bedienungsanleitung
ZALMAN
ZALMAN CNPS7000B-AlCu Bedienungsanleitung
ZALMAN
ZALMAN CNPS9900A LED Bedienungsanleitung
ZALMAN
ZALMAN CNPS9500 AM2 Bedienungsanleitung
ZALMAN
ZALMAN CNPS12X Bedienungsanleitung
ZALMAN
ZALMAN ZM80C Bedienungsanleitung
ZALMAN
ZALMAN Z8 Bedienungsanleitung
ZALMAN
ZALMAN ZM-RWB1 Bedienungsanleitung
ZALMAN
ZALMAN ZM-GWB3 Bedienungsanleitung
ZALMAN
ZALMAN CNPS2005-Plus Bedienungsanleitung
ZALMAN
ZALMAN Extreme Gaming VGA Cooler GV1000 Bedienungsanleitung
ZALMAN
ZALMAN CNPS6500B-AlCu Bedienungsanleitung
ZALMAN
ZALMAN CNPS9500 AT Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
