ZALMAN ZM80D-HP Bedienungsanleitung

www.zalman.co.kr www.zalmanusa.com

Product manual is provided in the following languages :

●

English

●

Korean

󳣍To better understand the installation process, check out the flash movie at our website

(www.zalman.co.kr).

※Please read this manual thoroughly before installation.

※The specifications of this product and its components may change without prior notice.

※Limited warranty : Parts and labor - 3 years (please see website for details)

ZM8 D-HP

www.zalman.co.kr www.zalmanusa.com

1. Please read this manual thoroughly before installation.

. This product is designed to accommodate an Optional Fan (ZM-OP1). You can expect satisfactory cooling performance with

this product alone, but If you want even more cooling, you can attach the Optional Fan (ZM-OP1).

3. If you are using a nVIDIA GeForce FX5800, an ATI Radeon 9800 Pro, a Matrox Parhelia, or a more advanced model, an Optional

Fan (ZM-OP1, sold separately) must be installed.

4. After installing this product on a VGA card (Video Graphics Card), the PCI slot adjacent to the AGP slot will be unusable.

5. If you plan to install this product on a recently released VGA card, check for compatibility at Zalman’s website (www.zalman.co.kr)

before installation.

6. If the heatpipe is tampered with or scratched by a sharp object, it may not function properly. Please handle with care.

7. Zalman does not recommend VGA card overclocking. Zalman is not responsible for any damage from VGA card overclocking.

8. After installing the VGA card, avoid shaking or exerting excessive force on the heatsinks on each side of the card, for it may

loosen the bolts in the Plate Spring.

9. To enhance the performance of this product, the use of a fan on the rear panel of the system’s case is recommended.

10. Do not eat the enclosed Thermal Grease.

Cautions & Warnings

On Use

1. This product can be installed if the Northbridge Cooler is shorter than

5 mm from the board’s base, or if taller be at least 5.5 mm away from

the AGP slot.

.If a Zalman CNPS7000 series Cooler is used, the CPU Retention Guide

should be at least 35 mm away from the AGP slot to install this product.

3. When installing the VGA card equipped with this product into a computer

system, opening up the PCI slot cover under the AGP slot can lower

the VGA Chipset temperature by as much as 4~5 ℃.

4. Since this product weighs 350 g, always firmly fasten the VGA card onto

the case with a screw. Special care should be taken while the computer

is being moved. Zalman is not responsible for any damage arising while

moving the computer.

5. If the components on the VGA card interfere in any way with this product,

you cannot install this product. In such case, stop the installation and

return the product.

6. Zalman is not responsible for any problems arising from incorrect

installation.

For installation

Fixing Bolt

❶❷

AGP Slot

(VGA Card)

open

PCI Slot Cover

❸

❹

www.zalman.co.kr www.zalmanusa.com

Heatsink Mounting

Hole (3 mm)

VGA Chipset

(X) (O)

Table of Contents

1. Features

2. Specifications

. Compatible VGA Cards

4. Components

5. Exploded View

6. Installation

7. ZM80D- HP Optional Fan Installation

8. Zalman Noise Prevention System

1. Features

1) This product was designed to optimize heat dissipation for excellent cooling performance.

) Dual heatpipes increase heat transfer speed and enhance the cooling efficiency.

3) The fanless design ensures complete noiselessness and maintenance-free operation.

4) RAM heatsinks for cooling the VGA RAM.

5) Compatibility with virtually all types of VGA cards allows reinstallation when upgrading the VGA card. (Incompatible with VGA

cards that do not have original heatsink holes measuring 3 mm in diameter, or VGA cards on which the ZM80D-HP interferes

with the card’s components.)

6) An Optional Fan (ZM-OP1, sold separately) can be attached to the heatsink directly without using a separate bracket.

2. Specifications

1) Weight : 350 g ) Heatpipe : Gold plated copper tube

3) Dissipation material : Anodized Aluminum 4) Heat Dissipation Surface Area : 1350 ㎠

5) VGA RAM Heatsink material : Anodized Aluminum 6) VGA RAM Heatsink weight :

Frontside : .9 g (EA)

Backside : 1. g (EA)

3. Compatible VGA Cards

Compatible with all VGA cards with original Heatsink Mounting Holes.

ZM8 D-HP

www.zalman.co.kr www.zalmanusa.com

Frontside Heatsink 1EA Backside Heatsink 1EA Heatpipe Cover 1EA Frontside Heatsink Base 1 Set

A Type B Type

Screw Driver 1EA

Backside Heatsink Base 1 Set

VGA RAM Heatsinks 1 Set Heatpipe A 1EA Heatpipe B 1EA

A TypeFrontside 4EA B TypeBackside 4EA

4. Components

Optional Components

●ZM80D-HP Optional Fan (ZM-OP1)

Fan Grill Assembly Multi Connector 1

●VGA RAM Heatsinks

Frontside Backside

●Thermal Tape

Assembly Parts 1 Set

Plate Link Nipple 4 EA

Washer 4 EA

Bolt A (10 mm) 4 EA

Bolt B (8 mm) 6 EA

Nut A EA

Rubber Ring EA

Nipple EA

Plate Link EA

Thermal Grease EA

Spare Parts 1 Set

Fan Bolt ( 6 mm) EA

Washer EA

Bolt A (10 mm) EA

Bolt B (8 mm) EA

Bolt C EA

Nut A 1 EA

Rubber Ring EA

Nut B EA

Nipple 1 EA

Thermal Grease 1 EA

Thermal Tape EA

www.zalman.co.kr www.zalmanusa.com

5. Exploded View

Sticker

Bolt B (8 mm)

Logo

Frontside Heatsink

Frontside

RAM Heatsink

Bolt A

Rubber Ring

Nipple

Nut A

Backside

Heatsink Base

Plate Link Nipple

Plate Link

Washer

Bolt A (10 mm)

Frontside Heatsink Base

Heatpipe A

Bolt B (8 mm)

Backside Heatsink

Bolt B (8 mm)

Heatpipe B

Backside RAM Heatsink

Plate Spring

Heatpipe Cover

ZM8 D-HP

www.zalman.co.kr www.zalmanusa.com

Good (O) Good (O) Bad (X) Good (O)

VGA

RAM

VGA

Chipset

Front

Back

Thermal Tape

Film

Frontside RAM

Heatsink

Backside RAM

Heatsink

VGA RAM Heatsinks

Compare your computer case with the cases in the diagram for compatibility. The ZM80D-HP cannot be used in systems in which

the VGA Chipset faces upwards. Such cases should not be flipped up-side-down to “correct” this incompatibility.

6. Installation

6.1 Verifying the Computer Case’s Compatibility

1) Peel off the Film from the Thermal Tape on the bottom of the

RAM Heatsinks.

) Stick the RAM Heatsinks onto the VGA RAMs. There are two

types of RAM Heatsinks - Frontside and Backside. Identify the

proper heatsink and attach appropriately.

Press the RAM Heatsinks firmly with your finger for proper adhesion.

(RAM Heatsinks can easily be detached. Please handle with care.)

4) If there are more than 8 RAMs on your VGA card, purchase

additional RAM Heatsinks.

6.2 Attaching VGA RAM Heatsinks

Note 1) Avoid getting grease or any kind of stain on the surface

of the Thermal Tape. The Thermal Tape may not stick.

Clean the surface of the RAM with acetone or alcohol

before attaching.

Note ) Thermal Tape loses adhesiveness after it has been

used once. Try to attach properly on the first attempt.

Note 3)Thermal Tape cannot be reused after it has been

detached from a surface. If you need more, purchase it

separately.

www.zalman.co.kr www.zalmanusa.com

Type A Type B

Frontside Heatsink Base

1) Clean off the contact surface of the VGA Chipset thoroughly.

) Evenly apply the Thermal Grease onto the VGA Chipset, using a piece of cardboard. Most VGA Chipset surfaces are slightly

concave and require more Thermal Grease towards the center.

6. Applying Thermal Grease on the VGA Chipset

There are two types of Frontside Heatsink Assembly - Type A and Type B. Use the Type B assembly for GeForce 4 Ti series.

Use the Type A assembly for all other VGA cards. If the Type A heatsink assembly cannot be installed, then install the Type B

heatsink assembly.

6.4 Selecting the Frontside Heatsink Base Assembly

1) Clean off the contact surface of the Frontside Heatsink Base thoroughly.

2) The Frontside Heatsink Base Assembly should be centered and tightly pressed onto the VGA Chipset.

3) Unscrew Bolt C half a turn and position each Plate Spring to insert Bolt A into the Heatsink Mounting Hole.

(Caution! Do not unscrew Bolt C completely.)

4) Once the Frontside Heatsink Base Assembly is centered, tighten Bolt C completely.

6.5 Installing the Frontside Heatsink Base Assembly

Note) If the Plate Spring separates from the base assembly, reinstall the Plate Spring onto the Frontside Heatsink Base

(Refer to installation step 6. 4) and restart installation from 6.5 step 3).

Thick Paper

Protective Frame for Core

< Example : ATI Radeon 9700 PRO >

VGA Chipset

Thermal Grease

VGA Chipset

Frontside Heatsink Base

Bolt C Bolt A

Plate Spring

Heatsink Mounting Hole

VGA Chipset

ZM8 D-HP

www.zalman.co.kr www.zalmanusa.com

Frontside

Heatsink Base

Backside Heatsink Base

Sticker

Nipple

Bolt A

Rubber Rings

Type A Type B

(O) (X)

Front

Back

Plate Spring

Backside

Heatsink Base

Slot Connecter

Bolt C

Groove

for Heatpipe

Nipple

1) Slide the Rubber Ring onto each Bolt A protruding out of the back of the VGA card.

) Screw a Nipple onto each Bolt A and tighten Bolt A with a screwdriver while holding the Nipple with one hand. While switching

back and forth between each Bolt A, tighten one full turn at a time for each Bolt A until both are tightened.

6.6 Assembling the Rubber Rings and Nipples

1) The Backside Heatsink Base Assembly must be the same type as the Frontside Heatsink Base Assembly.

e.g.) If the Type A was selected as the Frontside Heatsink Base Assembly →select the Type A for the Backside

Heatsink Base Assembly as well.

) Stick the sticker onto the bottom surface of the Base Assembly as shown in the diagram.

6.7 Selecting the Backside Heatsink Base Assembly and Attaching the Sticker

Note) Stick only one sticker onto the Backside Heatsink Base. Do not stick a sticker onto the bottom surface of the Frontside

Heatsink Base Assembly.

1) Install the Backside Heatsink Base so that the arrow of “BACK↓” points towards the Slot Connector.

) Unscrew each Bolt C half a turn and position each Plate Spring hole to be in line with the axis of each Nipple.

3) After the Backside Heatsink Base Assembly is in place, insert each Plate Spring hole onto the Nipple then tighten Bolt C.

6.8 Installing the Backside Heatsink Base Assembly (VERY IMPORTANT)

Note) The Plate Spring can easily be moved by slightly unscrewing Bolt C. Do not unscrew Bolt C completely.

www.zalman.co.kr www.zalmanusa.com

Tighten Nut A on the Nipple that now has the Plate Spring in place.

6.9. Installing the Backside Heatsink Base Assembly

1) Viewing from the side, make sure that both Heatsink Base Assemblies are parallel with the VGA card, and that their edges are

parallel to each other.

(If the Heatsink Base Assemblies are not aligned properly, the heatsinks cannot be installed properly.)

) Tighten each Bolt A and Bolt C completely.

6.1 Confirming Proper Installation of the Two Heatsink Base Assemblies (VERY IMPORTANT)

Evenly apply the Thermal Grease in the grooves of the Frontside Heatsink Base as shown in the diagram.

6.11 Applying Thermal Grease on the Frontside Heatsink Base

Nut A

Nipple

Rubber Ring

Nut

Bolt C

Bolt A

Bolt C

Backside Heatsink Base

Frontside Heatsink Base

Front

Back

Front Back

Frontside

Heatsink Base

Thermal

Grease

Thermal Grease Apply Thermal

Grease here

Thick

Paper

ZM8 D-HP

www.zalman.co.kr www.zalmanusa.com

Thermal Grease

Apply Thermal Grease here

(Grooves for Heatpipes)

Frontside Heatsink

Heatpipe A

Heatpipe B

Frontside

Heatsink Base

Heatpipe B

Heatpipe A

Heatpipe B

Frontside

Heatsink Base

50 mm

30 mm Frontside

Heatsink Base

< General VGA Cards >

Front

Back

Thick Paper

1) Slide in Heatpipe A and Heatpipe B into the grooves of the Base Assemblies.

) For general VGA cards, the end of the Heatpipes should protrude approximately 50 mm from the end of the Frontside

Heatsink Base, and for Geforce 4 Ti or FX59 series, they should protrude approximately 30mm.

6.12 Installing the Heatpipe

Evenly apply Thermal Grease in the heatpipe grooves of the Frontside Heatsink as shown in the diagram.

6.1 . Applying the Thermal Grease on the Frontside Heatsink

Andere Handbücher für ZM80D-HP

Andere ZALMAN Computerhardware Handbücher

ZALMAN

ZALMAN CNPS9700 LED Bedienungsanleitung

ZALMAN

ZALMAN ZM-RWB1 Bedienungsanleitung

ZALMAN

ZALMAN CNPS9X OPTIMA Bedienungsanleitung

ZALMAN

ZALMAN RESERATOR1 V2 Kurzanleitung

ZALMAN

ZALMAN CNPS8700 NT Bedienungsanleitung

ZALMAN

ZALMAN CNPS9500 AT Bedienungsanleitung

ZALMAN

ZALMAN CNPS7000B Series Bedienungsanleitung

ZALMAN

ZALMAN ZM-2HC2 Bedienungsanleitung

ZALMAN

ZALMAN ZM-WB3 Gold Bedienungsanleitung

ZALMAN

ZALMAN CNPS9500 AT Bedienungsanleitung

ZALMAN

ZALMAN CNPS7000B Series Bedienungsanleitung

ZALMAN

ZALMAN FS-V7 Bedienungsanleitung

ZALMAN

ZALMAN CNPS9800 MAX Bedienungsanleitung

ZALMAN

ZALMAN MS800 Bedienungsanleitung

ZALMAN

ZALMAN CNPS8000A Bedienungsanleitung

ZALMAN

ZALMAN CNPS8000B Bedienungsanleitung

ZALMAN

ZALMAN CNPS7000C-Cu/AICu Bedienungsanleitung

ZALMAN

ZALMAN CNPS5700D-Cu Bedienungsanleitung

ZALMAN

ZALMAN Z8 Bedienungsanleitung

ZALMAN

ZALMAN CNPS8700 NT Bedienungsanleitung

ZALMAN

ZALMAN CNPS 8000 Bedienungsanleitung

ZALMAN

ZALMAN ZM80C-HP Bedienungsanleitung

ZALMAN

ZALMAN CNPS10X Flex Bedienungsanleitung

ZALMAN

ZALMAN CNPS9500 AM2 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung