Zavio B8220 Bedienungsanleitung
1
8608586000060
ZAVIO Motorized Outdoor IR Bullet
Quick Installation Guide
/ B5210
2
Quick Installation Guide
Please follow the installation steps below to set up your IP camera.
Check the package contents with the list below. See P.2
Physical overview. See P.3
I/O Terminal Block Circuit. See P.4
I/O Terminal Block Pin Definition. See P.4
LED Indicator Definition. See P.5
Power Mode. See P.5
Installation of hardware and connection of all cables. See P.5
Windows: Go to Zavio website and download Camera Installation Tool. See P.9
Access the IP Camera using Camera Installation Tool. See P.10
MAC OS: using Safari Browser. See P.12
Lighting environment. See P.14
Change language of the web interface. See P.14
Application of IP Camera. See P.15
Package contents
Camera
IP camera
Quick Installation Guide
Brief product information and quick installation
Accessory
Sun shield and screws, Wall mount bracket,
Metal plate for wall mount bracket, Screw pack for wall
and ceiling mounting, Alignment sticker, Wrench for
front & back cover, Waterproof Connector, Desiccant
bag, Foam tape, 2 pin terminal blocks for power
Software
The following software and information are available online:
-Video Management Software
-Camera Installation Tool
-User manuals
-Camera Language Packs
Download the above at http://www.zavio.com/downloads.php or scan QR-Code.
To activate Video Management Software, please enter the license key below.
3
Physical overview
－Front －
Warning:
The IR LED is classified as class 3B laser IR. Avoid looking at the IR LEDs during
operation as direct and long term exposure might be harmful to the eye.
－Rear －
Light Sensor
Lens
IR LED
SD card/ Network Link
status indicator
Video out
Reset
I/O Terminal Block:
1: Ground,
2: +12VDC,
3: Audio in,
4: Audio out,
5: Digital Output 1,
6: Digital Output 2,
7: Digital Input 1,
8: Digital Input 2,
9: RS-485+,
10: RS-485-
Power status indicator
NTSC/ PAL switch
SD card slot
DC 12V Power
Smart Focus control
4
I/O Terminal Block Circuit
I/O Terminal Block Pin Definition
PIN
Definition
Description
Max. V/A
1
Ground
-
2
+ 12VDC
12V DC
1.2 W
3
Audio In
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
-
4
Audio Out
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
-
5
Digital
Output 1
Uses an NPN transistor with the emitter connected
to the GND pin. If used with an external relay, a
diode must be connected in parallel with the load for
protection against voltage transients.
100 mA
24V
6
Digital
Output 2
Uses an NPN transistor with the emitter connected
to the GND pin. If used with an external relay, a
diode must be connected in parallel with the load for
protection against voltage transients.
100 mA
24V
7
Digital Input
1
Connected to GND to activate, or leave floating (or
unconnected) to deactivate.
30V DC
8
Digital Input
2
Connected to GND to activate, or leave floating (or
unconnected) to deactivate.
30V DC
9
RS-485 +
-
10
RS-485 -
-
5
LED Indicator
LED
Color
Indication
Network
Blue
Solid blue when network is established.
Blink blue when there is network activity.
Power
Red
Solid red for booting up process
Blue
Solid blue for booting up completion
Unlit
When reset button pressed for at least 5 sec.
to factory default
SD Card
Yellow
Solid yellow means SD card ready
Blink yellow while accessing SD card
Power Mode
PoE
Mode
at
Power
Requirement
PoE (IEEE802.3at) with Class 4
Power
Consumption
15.9 W, with max. IR/ Heater/ Fan
af
Power
Requirement
PoE (IEEE802.3af) with Class 3
Note: While IR on, Heater and Fan will be disabled.
Power
Consumption
11.7 W, with max. IR on
Adaptor
Mode
Power
Requirement
12V/1.5A Adaptor
Power
Consumption
15.9 W, with max. IR/ Heater/ Fan
Note:
*Heater will activate when temparature drops below 5ºC and turn off when above 10ºC.
*Fan will activate when temparature is above 50ºC and turn off when drops under 45ºC.
Install the hardware and connect all cables
A. Hardware installation
a) Assembe sun shield and camera with the two supplied screws (M5*6L).
Note: Please move the sun shield to secure the first screw on the fourth scale.
6
b) Loosen back cover with supplied T25 wrench.
c) Unplug the seal at the bottom of the camera and plug the M12 waterproof
connector. Insert all cables (power cord/ DIDO/ video out) into the connector.
d) Connect the cables to the specific sockets on the back manual plate and tightly
secure waterproof connector.
e) Attach the desiccant bag to the back cover with the supplied foam tape, then
fasten the back cover accordingly. Recommend change desiccant bag everytime
the front/back cover is open.
7
f) Fix U-shape bracket to the bottom of camera with supplied screws.
g) Feed all cables through the front opening of the wall mount bracket.
h) Push the spring mortise of the wall mount bracket. Then hook the U-shape bracket
onto the groove of the former.
i) Secure the two screws of wall mont bracket on the other side.
B. Wall mounting and Ceiling mounting
a) Attached the alignment sticker to the wall. Drill four holes into the wall, three for
screws and one for cable. Then hammer the supplied plastic anchors into the screw
holes and secure the plate with supplied screws (T 1/4”*32).
8
b) Hang the wall mount bracket on the plate and fix it with the supplied screw.
c) Adjust the angle of the wall mount bracket to aim the desired area.
C. Connect all cables
E1. Without Power over Ethernet (PoE) connection
1. Connect the power adaptor to the IP Camera.
2. Use a standard RJ-45 network cable and connect the IP Camera to a
hub/switch/router.
9
E2. Power over Ethernet (PoE)
1. Use a standard RJ-45 network cable and connect the IP Camera to a PoE-enabled
hub/switch/router.
E3. RJ45 waterproof connector
1. Make sure all components are assembled as shown on the below graph.
2. Check that the Ethernet Port and the Waterproof main body are tightly fasten.
Windows: Go to Zavio Website and download Camera Installation Tool
Please go http://www.zavio.com/softwaredownloads.php download “Camera
Installation Tool”. And follow the installation process to complete the installation.
10
Access the IP Camera using Camera Installation Tool
1. Please check two settings before using Camera Installation Tool.
a. Browser’s Internet Properties →Security→Default Level
b. Browser’s Internet Properties →Privacy →Uncheck Pop-up Blocker
Andere Handbücher für B8220
1
Inhaltsverzeichnis
Andere Zavio IP-Kamera Handbücher
Zavio
Zavio P5110 Bedienungsanleitung
Zavio
Zavio N6031 Bedienungsanleitung
Zavio
Zavio F1100 Bedienungsanleitung
Zavio
Zavio F531E Bedienungsanleitung
Zavio
Zavio D5210 Bedienungsanleitung
Zavio
Zavio D5113 Bedienerhandbuch
Zavio
Zavio F3102 Bedienungsanleitung
Zavio
Zavio F521E Bedienerhandbuch
Zavio
Zavio F7220 Bedienungsanleitung
Zavio
Zavio D6330 Bedienungsanleitung
Zavio
Zavio F3102 Bedienungsanleitung
Zavio
Zavio D3100 Bedienungsanleitung
Zavio
Zavio F3100 Bedienungsanleitung
Zavio
Zavio F510E Bedienungsanleitung
Zavio
Zavio D7110 Bedienungsanleitung
Zavio
Zavio F3210 Bedienungsanleitung
Zavio
Zavio D3100 Bedienungsanleitung
Zavio
Zavio M511E Bedienungsanleitung
Zavio
Zavio B7320 3MP WDR Bedienungsanleitung
Zavio
Zavio D7111 Bedienungsanleitung
