Zortrax Z-NYLON Montageanleitung

Tips for Printing with Z-NYLON

SOURCE:

https://support.zortrax.com/z-nylon-tips/

Table Of Content

Storage & Preparation 3

Hardware Requirements 4

Model Preparation Tips 5

Printing Process Requirements 6

Storage & Preparation

Z-NYLON is highly hydroscopic and shouldn’t be stored without protection in humid

environments for a long time. Unused spools have to be stored in an airtight container

with a moisture absorber. Otherwise, the filament will absorb moisture from air which can

cause problems such as stringing or low surface quality of printed parts. Also, the color

of the filament can fade or become dull.

To remove moisture from the filament, perform a drying procedure at 90 °C [194 °F] for

2 hours.

Hardware Requirements

To create the best printing environment for Z-NYLON, it is best to equip your printer with

a separate hotend and a perforated plate that will be dedicated only for printing with this

material. These parts should be new and not used with other materials.

Also, avoid using adhesive substances with the new perforated plate.

Model Preparation Tips

As all nylon-based materials, Z-NYLON is highly prone to warping. That’s why, while

preparing your model in Z-SUITE, go to Advanced section in the Print settings step and

set the Fan speed to 0%.

If you’re preparing several small models for printing, make sure to separate them in the

workspace so that each item has its own raft structure. This way, a smaller printing area

can reduce the risk of warping.

Printing Process Requirements

While printing with Z-NYLON, it is recommended to provide proper conditions in the print

room. First of all, make sure that there are no draughts in your work area. Strong

airflows cause warping and may damage your print. Also, avoid printing in humid

conditions. Due to its high shrinkage, Z-NYLON is not recommended for printing large

geometric models with steep slopes in the Z axis. In general, models with walls that are

perpendicular to the platform will be less prone to warping. Still, it is advisable to add

support structures to all angles and overhanging parts of your model.

To reduce shrinkage, it is advisable to create a printing chamber with the use of Side

Covers and a HEPA Cover. These accessories have been designed to support the

printing process with materials of a high shrinkage rate.

Lastly, remove any residues of material extruded during the pre-print calibration. This will

facilitate adhesion of raft and the whole model to the perforated plate.

Powered by TCPDF (www.tcpdf.org)

Inhaltsverzeichnis

Andere zortrax 3D-Drucker Handbücher

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax M200 Plus Gebrauchs- und Pflegehandbuch

zortrax

zortrax Apoller Bedienungsanleitung

zortrax

zortrax M200 Plus Leitfaden

zortrax

zortrax M200 Gebrauchs- und Pflegehandbuch

zortrax

zortrax Inventure Merkblatt

zortrax

zortrax Inkspire Bedienungsanleitung

zortrax

zortrax M300 Bedienungsanleitung

zortrax

zortrax M200 Bedienungsanleitung

zortrax

zortrax M200 Plus Merkblatt

zortrax

zortrax M300 Merkblatt

zortrax

zortrax Z-Axis Bedienungsanleitung

zortrax

zortrax M200 Gebrauchs- und Pflegehandbuch

zortrax

zortrax M Series Gebrauchs- und Pflegehandbuch

zortrax

zortrax M300 Bedienungsanleitung

zortrax

zortrax M300 Plus Merkblatt

zortrax

zortrax M200 Plus Gebrauchs- und Pflegehandbuch

zortrax

zortrax M300 Plus Betriebsanleitung

zortrax

zortrax M200 Handbuch

zortrax

zortrax M200 Plus Gebrauchs- und Pflegehandbuch

zortrax

zortrax HEPA Cover Gebrauchsanweisung

zortrax

zortrax Inventure Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch