ZyXEL Communications P-2302R-P1 Series Bedienungsanleitung

P-2302R-P1 Series

VoIP ATA / Station Gateway

Quick Start Guide

Version 3.60

Edition 1

5/2006

P-2302R-P1 Series Quick Start Guide

Overview

This guide explains how to set up your P-2302R-P1 Series device (“P-2302R-P1“) to make phone calls over

the Internet. For the P-2302RL-P1, it also explains how to set up regular phone services that do not use the

Internet.

The following figure shows a typical way to use your P-2302R-P1.

When you make a phone call over the Internet, you use one of your telephones (A) to dial the number. The

telephones are connected to your P-2302R-P1 (C), which is connected to the broadband modem or router that

provides Internet access (D).

When you want to use the Internet, you use your computer (B). Your computer is connected to your P-2302R-

P1 (C), which is connected to the broadband modem or router that provides Internet access (D).

When you want to configure the P-2302R-P1 (C), you also use your computer (B).

1 Requirements

Make sure you have the following things before you set up your P-2302R-P1.

• Internet access - account information provided by your ISP, such as user name, password, and so on.

• VoIP account - You need the account information provided by your VoIP service provider (the company that lets

you make phone calls over the Internet). This information might include your URI, number, and so on.

• Internet Explorer 6.0 or later or Netscape Navigator 7.0 or later, with JavaScript enabled.

BCD

P-2302R-P1 Series Quick Start Guide

2 Hardware Connections

1LINE(P-2302RL-P1 only): Use a telephone cable to connect the telephone jack to this port.

2 PHONE 1-2: Use a telephone cable (and any telephone adaptors provided with your P-2302R-P1) to

connect your telephones to these ports. If you only have one telephone, you should only use one port.

3ETHERNET: Use an Ethernet cable to connect your computer to this port.

4WAN: Use an Ethernet cable to connect your broadband modem or router to this port.

5POWER:Use the power adaptor provided with your P-2302R-P1 to connect an appropriate power source

to this port.

On the front panel, the POWER light flashes green while your P-2302R-P1 starts up and stays green once it is

ready. The WAN and ETHERNET lights turn on if the WAN and ETHERNET ports are properly connected.

These lights flash when the P-2302R-P1 is sending or receiving data.

P-2302R-P1 Series Quick Start Guide

3 Initial Configuration

Use a web browser on your computer to set up your P-2302R-P1. See Troubleshooting if you have any

problems.

3.1 Open the Wizard Setup Screen

If the INTERNET light is green, go to section 3.3. Otherwise, go to section 3.2.

1Launch your web browser. 2Enter http://192.168.1.1 as the address or URL.

3Click Login.4Type a new password, re-type it to confirm, and

click Apply. (The next time you log in, you should

not see this screen.)

5Click Go to Advanced setup. 6 In the main screen, click the Wizard icon in the

upper right corner.

P-2302R-P1 Series Quick Start Guide

3.2 Connection Wizard

If you subscribe to a Roadrunner service, you cannot use the Connection Wizard to set up your Internet

connection. In this case, please see the User’s Guide for instructions.

Note: You must have Internet access before you can complete this section.

1In the Wizard Setup screen, click Connection

Wizard.

2Click Next.

3 System Name is used to identify the P-2302R-P1

in the network. Use the default value, unless you

know the name is already used in the network.

Domain Name (optional): Enter the appropriate

name, if there is one, or use the default value.

Click Next.

4This screen has different fields, depending on the

connection type (encapsulation) your ISP uses.

Select Ethernet or PPP over Ethernet (PPPoE). If

you are not sure and if your ISP gave you a user

name and password, select PPP over Ethernet.

Then, follow the instructions in the appropriate

section below.

P-2302R-P1 Series Quick Start Guide

3.2.1 Connection Wizard (Ethernet)

Follow these steps if your ISP uses an Ethernet connection.

1Click Next. 2 Select Get automatically from your ISP if your

ISP did not give you a static IP address. Then,

click Next, and go to step 4below.

Select Use fixed IP address provided by your ISP

if your ISP gave you a static IP address. Then, click

Next.

3Enter the information provided by your ISP. Use the

default values if your ISP did not provide the

requested information. Then, click Next.

4Select Factory default, unless your ISP has told

you to spoof your computer’s MAC address. Then,

click Apply.

5Click Finish.6Launch another web browser, and go to any web site

(for example, http://www.zyxel.com). If you cannot

access the Internet, see Troubleshooting.

P-2302R-P1 Series Quick Start Guide

3.2.2 Connection Wizard (PPP over Ethernet)

Follow these steps if your ISP uses a PPP over Ethernet (PPPoE) connection.

1Enter the information provided by your ISP. Use the

default values if your ISP did not provide the

requested information. Then, click Next.

2Select Get automatically from your ISP if your

ISP did not give you an IP address. Then, click

Next, and go to step 4.

Select Use fixed IP address provided by your ISP

if your ISP gave you a static IP address. Then, click

Next., and go to step 3.

3Enter the information provided by your ISP. Use the

default values if your ISP did not provide the

requested information. Then, click Next.

4Select Factory default, unless your ISP has told

you to spoof your computer’s MAC address. Then,

click Apply.

5Click Finish.6Launch another web browser, and go to any web site

(for example, http://www.zyxel.com). If you cannot

access the Internet, see Troubleshooting.

P-2302R-P1 Series Quick Start Guide

3.3 VoIP Setup Wizard

Note: You must have Internet access and a VoIP account before you can complete this section.

3.4 Bandwidth Management Wizard (Optional)

If you want to use the Bandwidth Management Wizard, please see the User’s Guide for instructions.

1In the Wizard Setup screen, click VoIP Setup.2Enter the information provided by your VoIP

service provider. If you have a VoIP account like

1234@VoIP-provider.com, the SIP Number is

1234, and the SIP Service Domain is VoIP-

provider.com.Use the default values if your VoIP

service provider did not provide the requested

information.

Select Check here to set up SIP2 settings if you

want to set up the second VoIP account in the P-

2302R-P1 now. In this case, enter the information for

the first VoIP account, click Apply, and enter the

information for the second VoIP account. You can

also set up the second account later. See the User’s

Guide for instructions.

Click Apply.

3Wait while the P-2302R-P1 tries to register the

VoIP account(s).

4Click Finish. The PHONE light should be green.

P-2302R-P1 Series Quick Start Guide

3.5 Regular Phone Line Configuration (P-2302RL-P1 only)

When one of your VoIP accounts is registered, the P-2302R-P1 normally uses the Internet (not the regular

phone line) to make phone calls. Follow the directions in this section to make sure you can also use the

regular phone line while one of your VoIP accounts is registered.

In the main screen, click VoIP > PSTN Line.

PSTN Line Pre-fix Number: If you want to make a regular phone call while one of your VoIP accounts is

registered, you have to dial this number before you dial the phone number.

Relay to PSTN Line: Enter phone numbers for regular phone calls (that do not use the Internet) that you

always want to dial without the prefix number. For example, enter emergency phone numbers here.

Click Apply.

3.6 Bridge Mode

The P-2302R-P1 supports two modes, Router and Bridge. Usually, you should use Router mode because it

supports all the features available in the P-2302R-P1. However, you might use Bridge mode in the following

situation:

• There is another router or gateway in the network; and

• You only want to use the P-2302R-P1 for VoIP and Internet access. You do not want to use other features, such

as the firewall, even with their default settings.

If you want to use Bridge mode, follow these steps.

P-2302R-P1 Series Quick Start Guide

1In the main screen, click Maintenance > System > General.

2In the Mode field, select Bridge.

3In the Management IP Address field, enter the IP address you want to use to access the P-2302R-P1 in

Bridge mode. For example, enter 192.168.5.1.

4Click Apply.

The P-2302R-P1 automatically restarts. When the POWER light stops blinking and stays on, follow the

directions in section 3.1 to log in to the web configurator again. However, use the Management IP Address

you set up in step 3, instead of http://192.168.1.1. If your computer’s IP address is in a different subnet, follow

the directions in the appropriate appendix of the User’s Guide to change your computer’s IP address.

See the User’s Guide for more details about Bridge mode.

4 Phone Calls

Follow these directions to make calls over the Internet.

• If you want to dial a SIP number that only uses numbers (for example, “12345”), dial the number on your

phone’s keypad. You can also set up a speed-dial entry, if you want. See the User’s Guide for instructions.

• If you want to dial a SIP number that uses letters or if you want to make a peer-to-peer call, set up a speed-dial

entry first. See the User’s Guide for instructions. Then, dial the speed-dial number to make the call.

• If you want to call regular telephone numbers, use your VoIP service provider’s dialing plan.

For the P-2302RL-P1, follow these directions to make phone calls that do not use the Internet.

• If you set up the phone number in the Relay to PSTN section (section 3.5), just dial the phone number.

• If the PHONE light is off, just dial the phone number.

• Otherwise, first dial the prefix you set in section 3.5, and then dial the phone number.

Note: If the P-2302RL-P1 is turned off, you can only use the phone that is connected to the PHONE1

port to make phone calls (regardless of the settings in any screen). Make sure you know which

phone this is, in case you want to make an emergency call.

Andere Handbücher für P-2302R-P1 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ZyXEL Communications Tor Handbücher

ZyXEL Communications

ZyXEL Communications P-660HWP-D1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-663HN-51 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2302R-P1C Handbuch

ZyXEL Communications

ZyXEL Communications PRESTIGE 2302RL - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-870HN-5xb Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG2881-T20A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EX5510-B0 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-27xx Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG1312-B Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL USG-1000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG9827-B50A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HWP-Dx Handbuch

ZyXEL Communications

ZyXEL Communications Prestige 660H Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL USG100-Plus Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications HLA3105 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL USG CLI Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HN-T1H Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 2302R Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications USG-300 - V2.20 ED 2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 971M Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-870HW-51A V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HN series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HW-Tx v3 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL IDP 10 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt