ZyXEL Communications FR1000Z Bedienungsanleitung

Introduction

FR1000Z is a router that provides high-speed Internet access, a built-in

switch, a firewall and high-speed wireless networking capability. It allows

you to enjoy high-bandwidth applications, such as video streaming, on-

line gaming and peer-to-peer (P2P). You can also set up a secure

wireless network connection using the WPS button.

Before You Begin

Make sure you have the following things before you set up your

FR1000Z.

• Internet access - account information provided by your ISP, such as

user name, password, and so on.

• Internet Explorer 6.0, Firefox 3.6, Safari: 4.0.5, Opera: 10.51 or

Chrome 4.1.249.1064 as well as later versions of all these

browsers, with JavaScript enabled.

Hardware Connections

This section shows you how to set up your FR1000Z.

1. WAN: Use an Ethernet cable to connect this port to an Ethernet jack

with Internet access.

2. ETHERNET: Use an Ethernet cable to connect a computer to this port

for initial configuration and/or Internet access.

3. Use the power adaptor provided with your FR1000Z to connect an

appropriate power source to this socket.

As of writing, the USB port is reserved for future use.

Checking the LEDs (Lights)

Look at the LEDs (lights) on the top panel of the FR1000Z.

• The POWER light blinks during start-up and is green once the

FR1000Z is ready.

• The WAN light is green if the Internet connection exists and blinks

when transmitting data.

• The INTERNET light is green when Internet access is available.

• The ETHERNET light turns on if the ETHERNET port is properly

connected. The light blinks when the FR1000Z is sending or

receiving data through the ETHERNET port.

• The WIFI light turns on when the wireless network is enabled.

If none of the LEDs (lights) are on, check your connections.

Make sure that you have the power adaptor connected to the

FR1000Z and plugged in to an appropriate power source.

Make sure the power source is turned on. Turn the FR1000Z

off, wait for a few seconds and turn it back on. If the LEDs

are still off, contact your local vendor.

As of writing, the USB LED is reserved for future use.

Testing Internet Connection

After you have connected the hardware and turned on the FR1000Z,

open a web browser on your computer and go to any web site (for

example, www.zyxel.com) to test your Internet connection.

If you are prompted for a user name and password, enter the account

information as given by your Internet service provider (ISP).

If the INTERNET light is off but the WAN light is on, go to the Initial

Configuration section to configure your Internet access settings.

Initial Configuration

1. Open your browser and enter http://192.168.0.1 (the FR1000Z's

default IP address) as the address.

2. The main screen displays.

If the main screen does not display, make sure your

computer is set to get an IP address automatically from a

DHCP server.

Click Quick Setup from the main screen. Follow the instructions in

the screen and enter the Internet access information exactly as given

to you by your ISP and click Apply.

3. If your ISP didn’t provide you a username and password, click the

Advanced IP Configuration button. Configure your FR1000Z for

Internet access according to instructions provided by your ISP. Make

sure you enter the correct information.

When your Internet connection is set up correctly, the WAN and

INTERNET lights should be green.

Set Up a WPS Connection

Press the WPS button on the FR1000Z’s front panel for more than 5

seconds to turn the WPS function on.

Follow these steps to add a WPS-enabled device to the wireless network

using the WPS button.

Place the devices you want to connect

near one another.

Press the WPS button on the FR1000Z.

The WPS light blinks.

Press the WPS button on a compatible

device within 2 minutes of pressing the

button on the FR1000Z.

The WPS light on the FR1000Z shines

steadily when connected.

Wall-mounting

Take the following steps to hang your FR1000Z on a wall.

1. Select a position free of obstructions on a sturdy wall.

2. Drill two holes for the screws, exactly 110 mm apart.

3. Be careful to avoid damaging pipes or cables located inside the wall

when drilling holes for the screws.

4. Do not insert the screws all the way into the wall. Leave a small gap of

about 0.5 cm between the heads of the screws and the wall.

5. Make sure the screws are snugly fastened to the wall. They need to

hold the weight of the FR1000Z with the connection cables.

6. Align the holes on the back of the FR1000Z with the screws on the

wall. Hang the FR1000Z on the screws.

Customer Information Statement

The information informing the user of his and the telephone company's

rights and obligations is outlined on the following pages. This information

will be included in the final version of the manual.

1. This equipment complies with Part 68 of the FCC rules and the

requirements adopted by the ACTA. On bottom of this equipment is

a label that contains, among other information, a product identifier of

QWEST FR1000Z. If requested, this number must be provided to the

telephone company.

2. If this equipment DL causes harm to the telephone network, the

telephone company will notify you in advance that temporary

discontinuance of service may be required. But if advance notice isn’t

practical, the telephone company will notify the customer as soon as

possible. Also you will be advised of your right to file a complaint with

the FCC if you believe it is necessary.

3. The telephone company may make changes in its facilities,

equipment, operations or procedures that could affect the operation

of the equipment. If this happens, the telephone company will provide

advance notice in order for you to make necessary modification to

maintain uninterrupted service.

4. If you experience trouble with this equipment, you disconnect it from

the network until the problem has been corrected or until you are sure

that the equipment is not malfunctioning.

5. Please follow instructions for repairing if any (e.g. battery replacement

section); otherwise do not alternate or repair any parts of device

except specified.

6. Connection to party line service is subject to state tariffs. Contact the

state public utility commission, public service commission or

corporation commission for information.

7. If the telephone company requests information on what equipment is

connected to their lines, inform them of:

a. The ringer equivalence number 02

b. The USOC jack required RJ14

c. The FCC Registration Number US: 1RODL02BQ1000Z

Item (a) and (c) are indicated on the label. The ringer equivalence

number (REN) is used to determine how many devices can be

connected to your telephone line. In most areas, the sum of the

RENs of all devices on any one line should not exceed five (5.0). If

too many devices are attached, they may not ring properly.

8. If your home has specially wired alarm equipment connected to the

telephone line, ensure the installation of this equipment does not

disable alarm equipment; consult your telephone company or a

qualified installer.

Service Requirements

In the event of equipment malfunction, all repairs should be performed

by our Company or an authorized agent. It is the responsibility of users

requiring service to report the need for service to our Company or to one

of our authorized agents.

Service can be facilitated through our office at:

ZyXEL Communications Corporation

6, Innovation Rd II, Science-Based Industrial Park, Hsin-Chu, Taiwan,

R.O.C.

+886- 3-578-3942

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

For a Class B digital device or peripheral, the instructions furnished the

user shall include the following or similar statement, placed in a

prominent location in the text of the manual:

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications XGS3700-24HP Betriebsanleitung

ZyXEL Communications

ZyXEL Communications Armor Z1 NBG6816 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ISDN 202H Plus Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660RU-Tx v3 SERIES Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL Dimension ES-105A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EXTRASMART ES-1528 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P964 APR 964 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3301-PLUS Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-202H Plus v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 645R-A Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications WAH7130 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL 2 WG Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-334WT Handbuch

ZyXEL Communications

ZyXEL Communications P-791R V2 - V3.40 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2602HWNLI-DxA Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3311 series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PMG1005-T20B Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 128IMH Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AX Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VES-1008 Handbuch

ZyXEL Communications

ZyXEL Communications P-2602H-D1A Referenzhandbuch

ZyXEL Communications

ZyXEL Communications P8802T Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660W-Tx Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL 2 WG Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung