ZyXEL Communications P-792H Bedienungsanleitung

ZyXEL Confidential

ZyXEL

Firmware Release Note

P792H

Standard version

Release 3.40(BZ.3)C0

Date: Nov 03, 2006

Author: Rongrong Guo

1/27

ZyXEL Confidential

ZyXEL P792H Standard Version

release 3.40(BZ.3)C0

Release Note

Date: Nov 03, 2006

Supported Platforms:

ZyXEL P792H

Versions:

ZyNOS Version: V3.40(BZ.3) | 11/03/2006 16:00:00

Bootbase Version: V1.14 | 11/10/2003 20:56:40

Notes:

Support Globespan modem code A.423.

Features:

Modifications in V3.40(BZ.3)C0 | 11/03/2006 16:00:00

1. Change to FCS.

Modifications in V3.40(BZ.3)b2 | 10/25/2006 10:00:00

1. [FEATURE ENHANCE] Add MTU

2. [FEATURE ENHANCE] Multi Routing Mode dynamic PVC support

3. [FEATURE ENHANCE] IPPR V2 support to forward the traffic by

remote node(PVC)instead of gateway IP Address

4. [BUG FIX]

SPRID:060727813

Symptom: Content filter schedule can’t be canceled

Condition: Step 1.Enable keyword blocking and edit key words. Step2. Enter Schedule

page and unselect all check boxes. Step3. The web site in the key words list also can

be blocked.

5. [BUG FIX]

SPRID: 060727816

Symptom/Condition: Throughput in route mode downstream can’t pass PQA criteria

with IES5000 DSLAM. (Throughput with IES5000 SHDSL DSLAM is much worse

than it with IES1000 SHDSL DSLAM).

6. [BUG FIX]

SPRID:060727807

Symptom: Release note is not correct

Condition: FW version in Menu 24.2.1 shows V3.40(BZ.2)|10/11/2005

2/27

ZyXEL Confidential

Modifications in V3.40(BZ.3)b1 | 02/28/2006 09:32:11

1. [FEATURE ENHANCE] Add Cone NAT .

2. [FEATURE ENHANCE] Add VPN NAT TRAVERSAL.

3. [BUG FIX]

SPRID: 060301057

Symptom: In GUI/smt, when choosing WAN backup mechanism as DSL Line, you

have to key in one check WANIP which is not reasonable.

Condition:N/A

4. [BUG FIX]

SPRID: 060301060

Symptom: If you enter one check WANIP, even the backup mechanism is “DSL Link”,

P792H will also ping that IP address periodically.

Condition: N/A

5. [BUG FIX]

SPRID: 060301061

Symptom: Open its WEB GUI with 192.168.1.1,in “advanced setup” list, there is a

option “logs”. When we click it, we can only get a wrong page of “the page cannot be

found” each time.

Condition: N/A

Modifications in V3.40(BZ.2) | 10/11/2005 10:32:11

1. Change to FCS

Modifications in V3.40(BZ.2)b2 | 09/23/2005 15:32:11

1. [BUG FIXED] 050914568

Symptom: The IP routing Policy don＇t work properly

Condition: step1 Setup one IP routing Policy rule (in SMT 25),If traffic matches ippr

rule, traffic will go out through appointed gateway, but failed

Modifications in V3.40(BZ.2)b1 | 09/07/2005 15:32:11

1. [FEATURE CHANGED] Add feature MBM.

2. [FEATURE CHANGED] Add port based VLAN.

3. [BUG FIXED] 050909370

Symptom& Condition: Key in”http://192.168.1.1/rpFWUpload.html”in IE, can login

in Firmware page without user name and password, then user can do romreset and

upload new firmware.

4. [BUG FIXED] 050909373

Symptom: Traffic redirect function cannot work properly at ENET-ENCAP with static

setting.

Condition: In menu 4 when using ENET ENCAP encapsulation and set static address.

In menu 2, we set a traffic redirect function, it could not work properly.

5. [BUG FIXED] 050909374

Symptom: The GUI\Wizard Setup can save the no match IP.

Condition: While set the DUT LAN “Client IP Pool Starting Address” and “Size of

Client IP Pool” which are not match the “IP Subnet Mask”, but this can be saved in

GUI\Wizard Setup and rom-t. In SMT and GUI\Advanced Setup have no this issue.

6. [BUG FIXED] 050909375

Symptom: if we change remode IP address or gateway in menu 4 or menu11, the

3/27

ZyXEL Confidential

previous routing entry still keep. it can see in CI command:ip route status.

Condition: In menu4 or menu11,Configure Enet Encap=static IP, then change to

PPPoE dynamic, in menu24.8, check the route table, the Enet Encap entry still

existed.unless you restart the DUT.

7. [BUG FIXED] 050909376

Symptom: After save DNS server, In CI command: ip ping www.hinet.net, it can not

be work and it must reboot.

Condition: We save DNS server in menu 3.2 after reset default rom file and if we don’t

reset system and issue ”ip ping www.hinet.net” that it can not be work and it must

reboot.

8. [BUG FIXED] 050909377

Symptom: When DUT use static IP and set DNS server address in GUI->wizard, DUT

won’t resolve domain name successfully until reboot

Condition: Step1 Go to GUI, configure DUT use static IP and set DNS server, then go

to Maintenance->Diagnostic, try to resolve domain name, but failed; Step2 Reboot

DUT, it works fine; Step3 This many cause TMSS/AV/CAC/DDNS functions doesn’t

work for these functions need DUT resolve domain name.

9. [BUG FIXED] 050909378

Symptom& Condition: enter eWC NAT, click the edit detail of full feature will apply

full feature.

10. [BUG FIXED] 050909379

Symptom& Condition: While delete menu4, then go to GUI to change NAT mode and

then apply in GUI, then go to SMT menu 24.1will cause crash.

11. [BUG FIXED] 050909380

Symptom: PPPOE nailed-up work have problem

Condition: Step1 use PPPOE and nailed-it up; Step2 in SMT menu 26.1 set a schedule

start time 00:03 and duration time is 00:02 and force down; Step3 in menu11.1

schedule set =1, now time is 00:02 when time is 00:03 then PPPOE turn down, but time

is 00:05 the PPPOE can not turn up, then in menu 24.8 command “d d 1” still can not

turn up.

Modifications in V3.40(BZ.1)C0 | 6/28/2005 13:32:11

1. [FEATURE CHANGED] Change to FCS.

Modifications in V3.40(BZ.1)b3 | 6/22/2005 9:53:09

1. [FEATURE CHANGED] Support new modem code A.423.

Modifications in V3.40(BZ.1)b2 | 3/28/2005 9:09:08

1. [FEATURE CHANGED] Support new modem code R3.0.1

2. [FEATURE CHANGED] Support new MAC, atwz , sys atwz command

3. [FEATURE CHANGED] Change hw version to 1 in bootbase , and after we change

AFE , this f/w can support new hardware and old hardware.

4/27

ZyXEL Confidential

Modifications in V 3.40(BZ.1)b1 | 04/07/2004

1. [BUG FIXED]

Symptom: User name/Password have one space at eWC.

Condition: Restore to default ROM file and chage to PPPoA/PPPoE mode, there is one

space at User name/Password field at eWC.

Modifications in V 3.40(BZ.0)C0 | 03/12/2004

1. Change to FCS version

Modifications in V 3.40(BZ.0)b2 | 03/05/2004

1. [FEATURE ENHANCED]

Support SIP pass-through.

Modifications in V 3.40(BZ.0)b1 | 01/07/2004

1. Create Project.

2. [FEATURE ENHANCED]

Support Wan Backup.

3. [FEATURE ENHANCED]

Support Firewall and Content Filter.

4. [FEATURE ENHANCED]

Support VPN

5. [FEATURE ENHANCED]

Support H.323v2 for NAT.ALG

5/27

ZyXEL Confidential

Annex A CI Command List

Command Class List Table

System Related Command Exit Command Ethernet Related Command

WAN Related Command IP Related Command Bridge Related Command

XDSL Related Command

SystemRelatedCommand Home

Command Description

sys

adjtime retrive date and time from Internet

atsh display MRD field

callhist

display display call history

remove <index> remove entry from call history

countrycode [countrycode] set country code

date [year month date] set/display date

domainname display domain name

edit <filename> edit a text file

extraphnum maintain extra phone numbers for outcalls

add <set 1-3> <1st phone num> [2nd phone

num] add extra phone numbers

display display extra phone numbers

node <num> set all extend phone number to remote node

<num>

remove <set 1-3> remove extra phone numbers

reset reset flag and mask

feature display feature bit

hostname [hostname] display system hostname

log

clear clear log error

disp display log error

online [on|off] turn on/off error log online display

stdio [second] change terminal timeout value

time [hour [min [sec]]] display/set system time

trcdisp parse, brief, disp monitor packets

syslog

server [destIP] set syslog server IP address

facility <FacilityNo> set syslog facility

type [type] set/display syslog type flag

mode [on|off] set syslog mode

version display RAS code and driver version

view <filename> view a text file

wdog

switch [on|off] set on/off wdog

cnt [value] display watchdog counts value: 0-34463

romreset restore default romfile

socket display system socket information

ddns

debug <level> enable/disable ddns service

display <iface name> display ddns information

restart <iface name> restart ddns

logout <iface name> logout ddns

6/27

ZyXEL Confidential

cpu

display display CPU utilization

xmodemmo

de [crc|checksum] select xmodem mode

ExitCommand Home

Command Description

exit exit smt menu

Ethernet Related Command Home

Command Description

ether

config display LAN configuration information

driver

Cnt

disp <name> display ether driver counters

Status <ch_name> see LAN status

config [0|1=auto|normal] [0|1=10|100]

[0|1=HD|FD] <ch-name> Configure LAN Settings Auto/Normal, 100/10

Mbps, Half/Full Duplex

version see ethernet device type

WANRelatedCommand Home

Command Description

Wan atm test [fix|rand|period|oam|loopback] Generate ATM traffic

hwsar Disp Display hwsar packets incoming/outgoing

information

Clear Clear hwsar packets information

Sendoam Send OAM packets: <vpi> <vci> <f5>

<end-to-end> <type:0(AIS) 1(RDI)

2(LoopBack)>

IPRelatedCommand Home

Command Description

address [addr] display host ip address

alias <iface> alias iface

aliasdis <0|1> disable alias

arp

status <iface> display ip arp status

dhcp <iface>

client

release release DHCP client IP

renew renew DHCP client IP

status [option] show dhcp status

dns

query

stats

clear clear dns statistics

disp display dns statistics

icmp

status display icmp statistic counter

discovery <iface> [on|off] set icmp router discovery flag

ifconfig [iface] [ipaddr] [broadcast <addr>

|mtu <value>|dynamic] configure network interface

7/27

ZyXEL Confidential

ping <hostid> ping remote host

route

status [if] display routing table

add <dest_addr|default>[/<bits>]

<gateway> [<metric>] add route

addiface <dest_addr|default>[/<bits>]

<gateway> [<metric>] add an entry to the routing table to iface

addprivate <dest_addr|default>[/<bits>]

<gateway> [<metric>] add private route

drop <host addr> [/<bits>] drop a route

status display ip statistic counters

udp

status display udp status

tcp

status [tcb] [<interval>] display TCP statistic counters

xparent

join <iface1> [<iface2>] join iface2 to iface1 group

break <iface> break iface to leave ipxparent group

igmp

debug [level] set igmp debug level

forwardall [on|off] turn on/off igmp forward to all interfaces flag

querier [on|off] turn on/off igmp stop query flag

iface

<iface> grouptm <timeout> set igmp group timeout

<iface> interval <interval> set igmp query interval

<iface> join <group> join a group on iface

<iface> leave <group> leave a group on iface

<iface> query send query on iface

<iface> rsptime [time] set igmp response time

<iface> start turn on of igmp on iface

<iface> stop turn off of igmp on iface

<iface> ttl <threshold> set ttl threshold

<iface> v1compat [on|off] turn on/off v1compat on iface

robustness <num> set igmp robustness variable

status dump igmp status

BridgeRelatedCommand Home

Command Description

bridge

cnt related to bridge routing statistic table

disp display bridge route counter

clear clear bridge route counter

stat related to bridge packet statistic table

disp display bridge route packet counter

clear clear bridge route packet counter

XDSLRelatedCommand Home

Command Description

xdsl

state display XDSL status about physical layer

restart restart XDSL driver

cnt disp display xdsl error counter

clear clear xdsl error counter

8/27

ZyXEL Confidential

Internal Information:

1. Modification.

Modifications in V 3.40(BZ.1)b1 | 04/07/2004

1. [FEATURE CHANGED]

Modify the way of LED display for HTP test and always not to display UART External

Loopback test item.

(1) normal case: SYS LED blinking per 1 second.

(2) SYS LED always on.

Modifications in V 3.40(BZ.0)b2 | 03/05/2004

1. [BUG FIXED]

Symptom: In VPN-Summary, the content of rules number greater than 5 are not

updated.

Condition: 1. Configure VPN rule 6 & save

2. Delete VPN rule 6

3. In VPN-Summary page, rule 6 still exist.

2. [BUG FIXED]

Symptom: CI-command "ip smtp sendmail" cause device reboot.

Condition: Type CI-command "ip smtp sendmail" will cause device reboot.

3. [BUG FIXED]

Symptom: Not update DNS information.

Condition: If ISP assigns different DNS after PPP connection, the device will

not update the DNS information.

4. [BUG FIXED]

Symptom: qlm error or traffic is blocked

Condition: qlm error bug:

1). Setup 2 remote node, node 1 is RFC-1483 bridge mode.node 2 is

routing mode with PPPoE nailed-up.

2). Actuality, node 2 just there and do nothing.

3). Heavy traffic through our device will cause qlm error.

Modifications in V 3.40(BZ.0)b1 | 01/07/2004

1. [FEATURE CHANGED]

Enlarge Rom File to 48K byte.

Known Issues:

1. AX/4000 will occur PRBS Bit Error Count.

2. Manufactory Data in Bootbase

9/27

ZyXEL Confidential

ZyNOS Version : V3.40(BZ.3) | 11/03/2006 16:00:00

Bootbase Version : V1.14 | 11/10/2003 20:56:40

Vendor Name : ZyXEL Communications Corp.

Product Model : Prestige 792H

ZyNOS Code Model : P792H STU-R

HTP Code Model : HTP_P792H V 0.2

ZyNOS ROM address : bfc10000

System Type : 7

MAC Address : 001349000001

Default Country Code : FF

Boot Module Debug Flag : 01

RomFile Version : 3A

RomFile Checksum : 6f66

ZyNOS Checksum : 4fae

Core Checksum : 73f7

SNMP MIB level & OID : 060102030405060708091011121314151617181920

Main Feature Bits : 86

Other Feature Bits :

92 3B 00 00 01 00 00 00-00 00 00 00 00 00 00 00

00 00 00 00 00 00 00 00-02 00 13 00 00 00

Notes:

•Debug Flag should be 0 after production. In our default release will be 1. Because in the

manufacture process will need it to set the MAC address.

•MAC address will be changed by production process. Only the fist 3 octets will be correct. The last

3 octets will depend on the production process.

3. Default ROM File Value Setting

·Menu 1: General Setup

Menu 1 - General Setup

System Name= ?

Location=

Contact Person's Name=

Domain Name=

Edit Dynamic DNS= No

Route IP= Yes

Bridge= No

Press ENTER to Confirm or ESC to Cancel:

·Menu 1.1: Configure Dynamic DNS

Menu 1.1 – Configure Dynamic DNS

Service Provider= WWW.DynDNS.ORG

Active= No

Host=

10/27

Andere Handbücher für P-792H

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications Unified Security Gateway ZyWALL 300 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HN-51 - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-334W Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-116P Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 2602HL Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660R-T1/T3 V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 2802HW(L)-IX Handbuch

ZyXEL Communications

ZyXEL Communications PES-100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2900-4HB Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige P-662HW-61 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AMG1202-T10B Handbuch

ZyXEL Communications

ZyXEL Communications ES-3124F Handbuch

ZyXEL Communications

ZyXEL Communications VES1724-56 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications WAH7130 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications WAH7003 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8623-T50B Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ADSL2+ Ethernet / USB Router P-660RU-Tx v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8825-B Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG318S v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 320W Handbuch

ZyXEL Communications

ZyXEL Communications ES-2108 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2302R-P1C Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660R-T1 v3 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL Dimension ES-2724 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise