A.O. Smith Jaguar HSE-SNJ-015 Bedienungsanleitung

Water Heater

HSE-SNJ-015 / HSE-SNJ-025

Size: 210mm (H) x 148mm (W)

Part No.: 326221-000_R0

Updated on: 12-04-2013

User Guide

Contents

What's in the box?

Electric

Water Heater

Wall Mounting

Accessories

Discharge Tube

User Guide

Specifications........................................................................................ 1

Key Features.......................................................................................... 2

Installation............................................................................................ 3

Directions for use ................................................................................. 5

Troubleshooting ................................................................................... 6

Circuit Diagram .................................................................................... 6

Warranty Card ...................................................................................... 7

Jaquar & Company Pvt. Ltd. ................................................................ 13

Water Heater

HSE-SNJ-015 / HSE-SNJ-025

User Guide

Specifications

Caution: *Safety valve has been factory fit with the water heater and set at 0.8 MPa

(8 Bar) rated pressure.

Warning: Do not tamper or detach the safety valve from the water heater during installation

and usage

1 Outlet

2 Inlet

3 Safety Valve*

4 Temperature Control Knob

5 Front Panel

6 Front Jacket

7 Back Jacket

8 Anode

9 Heating Element

10 Tank

11 Installation Bracket

12 PU Insulation

13 Thermal Cutout

Part Descriptors

Model HSE-SNJ-015 HSE-SNJ-025

Volume [L] 15 25

Power [W] 2000 2000

Voltage/Frequency [V/Hz] ~230/50 ~230/50

Actual Stdg. Loss [kWh/24h/45°C diff.] 0.592 0.721

Max. Stdg. Loss [kWh/24h/45 C diff.]

[as per IS 2082:1993 amended in 2002] 1.138 1.386

Reheating Time for 35°C rise [in min] 18 29

Temperature range [°C] 25-75 25-75

Rated water pressure N/cm 80 80

Water head (metres) 80 80

Inlet/Outlet connections [Inch] ½ ½

B2 B1

Model HSE-SNJ HSE-SNJ

-015 -025

A [mm] 373 444

B1 [mm] 373 444

B2 [mm] 405 483

C [mm] 348 383

Dimensions

Key Features

Note: A. O. Smith reserves the right to amend or modify the specifications and features at

any time, as and when required without any prior notification.

Blue Diamond technology increases the life of the inner tank. The lining is

stronger and more corrosion resistant than any other in the industry.

Blue Diamond Glass Lining

Anode Rod

The safety valve is designed to automatically relieve and discharge water in case

the pressure overshoots the preset limits.

Safety Valve

If the water temperature exceeds the highest preset level, the breaker rapidly

cuts off the live line and the neutral line simultaneously to assure safety.

Thermal Cutout

Temperature Control Knob

The temperature control knob allows you to set the temperature precisely

between 25°C to 75°C .

The tank has an anode rod which has stainless steel core that is designed to

protect the tank from corrosive elements. The anode rod uses a special cathodic

action to fight these elements and thus prolong the life of the water heater.

Installation

Mounting

Fig. 1 Position for installation Fig. 2 Wall mounting bracket

1. Make sure that the wall can withstand at least twice the weight of the water heater when

completely filled with water.

2. Before locating the position for installation of the water heater, make sure that there is

sufficient clearance between the ceiling and the side wall. (Fig. 1)

3. Use a drill bit with diameter of 10mm to drill 4 holes at least 90mm deep in the wall (Fig.

3). The four holes should be aligned horizontally and vertically. The horizontal distance

between the 2 holes should be 120mm and the vertical distance should be 57mm. (Fig. 2)

4. Insert the expansion anchors into the holes. Place the wall mounting bracket over the

expansion anchors and tighten the screws on the bracket. (Fig. 3)

5. Place the water heater on wall mounting bracket (Fig. 4) using hanger hooks. Tug

downwards on the heater to ensure that the water heater is fixed steadily.

Wall

Fig. 3 Installation of wall mounting

bracket

Ceiling Wall

*Flexible Hoses to be procured by the customer, not part of standard product.

Fig. 5 Installation diagram

Hot Water Tap

Cold Water Tap

Discharge Tube

*Flexible Hose

Lever

To Drain

Safety Valve

Blue Cap

Red Cap

Fig. 4 Inserting the water heater

into mounting bracket

Wall Water

Heater

Water

Heater

Wall

Water

Heater

Wall

Water heater

1. Open a hot water faucet nearby to permit the air to escape.

2. Open the cold water inlet valve fully, filling the heater and the piping.

3. Close the hot water faucet when water flows.

4. Check all the connections to see if there is any leakage. In case of a leakage, drain the

heater completely, repair the leaking joint and then refill the heater.

Electrical Connections

The power cord and plug are connected with this water heater. Find a separate socket for

power plug and make sure the socket is in firm contact with the plug. Ensure that reliable

earthing has been done.

Caution:

• Connect the water heater using independent sockets, do not use adapters. Use

multimeter to check whether the live line and neutral line are not reverse, to ensure

complete safety.

• Before installing the water heater, confirm that the power of water heater matches

electric meter capacity and supply wire.

• The water heater should be earthed reliably. It is prohibited to connect the earth wire

to neutral wire or tap water pipe.

Attention:

• Make sure a suitable sealing tape is used for all connections to prevent leakage.

• Discharge tube should be installed downwards without any loops, folds or knots.

Ensure that the free end of the Discharge tube is placed over a suitable drain and away

from the users.

• Discharge tube is provided to release the discharge from the water heater(through the

safety valve) in case excessive pressure is developed. The contents of the discharge

from the Safety valve may be hot and may cause burns to the users and damage

nearby objects if not properly routed to a drain.

• It is recommended to operate the discharge lever in the safety valve on a regular basis

to ensure that there are no blockages and also to remove any lime deposits that would

have been formed inside the water heater.

• Ensure that the water heater is in power OFF condition when the Discharge lever is

being operated. Ensure that the water is filled completely in the water heater before

switching it ON.

Water Filling

Plumbing

1. Make necessary plumbing with reference to the installation diagram. (Fig. 5)

2. A. O. Smith recommends nylon/SS braided hoses having a minimum pressure rating of

8 Bar and hoses should be compatible for hot water applications.

3. Connect the cold water pipe to the inlet [Blue Cap].

4. Connect the hot water pipe to the outlet [Red Cap].

5. Attach the discharge tube to safety valve as shown in installation diagram. (Fig. 5 & 6)

For draining water from the water heater, following steps

needs to be followed:

1. Switch off the electric supply to the water heater.

2. Open the hot water taps until the water is not hot any

more.

3. Close cold water supply.

4. Drain the water by moving the lever of safety valve in the

direction of the arrow as indicated in the diagram. (Fig. 6)

Draining

Fig. 6 Safety valve

Caution:

• Before using the water heater, make sure that it should be completely filled with water.

• Please turn off the power supply to the water heater prior to draining the water heater.

Warning: This water heater should not be operated with insufficient amount of water.

Failure to do so may result in damage to the water heater & injuries to the users. This

will also make the warranty null & void.

Caution:

• Once the mounting, plumbing, discharge tube, power connection and water filling

is completed, then only the power supply should be given.

• During repair or periodic maintenance, if necessary, the power cord or Internal

electrical wiring should be replaced by authorised service personnel only.

• It is not permitted for the power supply plug and cord to be replaced or altered by

unauthorised people or by the users themselves. This will make the warranty null and

void and may cause the water heater operation hazardous.

Directions for use

1. Switch on the water heater’s power supply.

The green indicator light glows.

2. Turn the thermostat knob clockwise for the

device to commence heating and change

the set temperature. A red light will glow.

[The set temperature increases if the

thermostat knob is turned clockwise.]

Temperature can be set in the range of

25°C to 75°C. Recommended to keep

thermostat knob notch position always in

medium or above level.

3. The red light’s switching off indicates the

heater has been heated to the set temperature.

Caution: Before using the water heater, make sure the inner tank is completely filled with

water and the power plug has been connected properly.

Fig. 7 MEDIUM

HIGH

LOW

Discharge Tube

Safety Valve

Port

Troubleshooting

Circuit Diagram

Element

Red Red Brown

Black

Thermostat

Green/Yellow

Black

White White

Thermal cutout

Green light Red light

Problem Possible Cause(s) Solution

• Green and Red No power to heater Turn on electrical switch. Check for

light off blown fuses or tripped breaker

• No hot water Thermal cutout switch open Call Customer Care Centre

Control circuit or internal Call Customer Care Centre

wiring error

• Green light on Non-functioning Call Customer Care Centre

Red light off thermostat

• No hot water Control circuit or internal

wiring error

• Water temperature Thermostat set is too high Call Customer Care Centre

is too high

Thermal cutout trips Call Customer Care Centre

• Water heats slowly Non-functioning element Call Customer Care Centre

• Thermostat does Non-functioning Call Customer Care Centre

not shut off thermostat

Improper calibration Call Customer Care Centre

• Piping connection Connection not sealed Call plumber

leaks

• Leaky cover Tank or parts leak Shut off power immediately and

Call Customer Care Centre

Dear Customer,

Congratulations! You have bought a world-class product manufactured by A. O. Smith India Water

Heating Private Limited. It is a wholly owned subsidiary of A. O. Smith Corporation (A. O. Smith).

A. O. Smith is one of the largest water heater manufacturer in the world and a global leader in

innovative technology and energy efficient solutions. Jaquar, the leader in the Indian bath fitting

industry has always emphasised on Quality, Reliability and Service. The key philosophy of Jaquar is

to provide consumers more value for their money. The reason why Jaquar believes in that - Its

products must make Friends not just Customers.

To further its commitment to customer delight, Jaquar offers an exclusive premium range of water

heaters manufactured by A. O. Smith India Water Heating Private Limited.

Our customer-centric approach manifests in many ways. Jaquar has the largest sales and after sales

network with 22 regional centres, over 2200 local dealers complemented by over 225 service

technicians.

If you need any further assistance, please call our Customer Care.

Keep smiling for years to come.

Customer Care No.

1.800.121.6808

J A QUA R CUS T O M ER C A R E ( A )

C O N D IT I ONS O F W A R R A N T Y

• This warranty certificate must be duly filled, stamped and signed by the dealer.

This certificate must be preserved and produced whenever required.

• During the warranty period and under normal use, if the product is found to be of

faulty manufacture, the same will be repaired or replaced upon production of this

warranty certificate, at our option, without charge either for part or labour.

No allowance however, will be mode for labour, transport charges consequential

damages, losses or any other incidental expenses incurred.

• This warranty is not valid for damage resulting from faulty installation,

mishandling, negligence, accidents and unauthorised repairs.

We hereby warrant this product against failure arising through faulty designs,

material or workmanship for a period as mentioned below from the date of purchase

subject to certain conditions specified.

HSE-SNJ

• Tank - 5 years

• Heating Element - 2 years

• Rest of the parts - 2 years

Name of Buyer: ..........................................................................................................

Address: ....................................................................................................................

..................................................................................................................................

Ph: ............................. Mobile: ............................... E-mail: ......................................

Date of Purchase: ............................................ Invoice No.: .......................................

Dealer's Name & Address

(Stamp)

..............................................................

.............................................................. ..................................

.............................................................. Signature of the Buyer

Jurisdiction: The courts of competent jurisdiction at Bangalore, Karnataka shall have exclusive

jurisdiction over all matters arising out of any disputes in relation to the product.

Warranty Card

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere A.O. Smith Boiler Handbücher

A.O. Smith

A.O. Smith BTI - 65 Leitfaden

A.O. Smith

A.O. Smith SGS-28 Fehlerbehebungshandbuch

A.O. Smith

A.O. Smith DEL Bedienungsanleitung

A.O. Smith

A.O. Smith BTC 201 Bedienungsanleitung

A.O. Smith

A.O. Smith DSE-5 THRU DSE-120 Bedienungsanleitung

A.O. Smith

A.O. Smith SGS - 100 Beilage

A.O. Smith

A.O. Smith BTR 120-400 Anleitung zur Verwendung

A.O. Smith

A.O. Smith BFC Cyclone Fehlerbehebungshandbuch

A.O. Smith

A.O. Smith 0 Bedienungsanleitung

A.O. Smith

A.O. Smith GCV/XCV 65/65L Bedienungsanleitung

A.O. Smith

A.O. Smith Duraclad Lime Tamer Bedienungsanleitung

A.O. Smith

A.O. Smith BTN 120 THRU 400/A Series Bedienungsanleitung

A.O. Smith

A.O. Smith 315456-004 Produktinformationsblatt

A.O. Smith

A.O. Smith 52 Bedienungsanleitung

A.O. Smith

A.O. Smith T-D2-OS Bedienungsanleitung

A.O. Smith

A.O. Smith DME 150 - 1000 Anwendungshandbuch

A.O. Smith

A.O. Smith ProMax SL Bedienungsanleitung

A.O. Smith

A.O. Smith BTR 120 Betriebsanleitung

A.O. Smith

A.O. Smith Jaguar Bedienungsanleitung

A.O. Smith

A.O. Smith ProMax Direct-Vent GDV-40 Bedienungsanleitung

A.O. Smith

A.O. Smith GPCR Bedienungsanleitung

A.O. Smith

A.O. Smith Series 100/101 Bedienungsanleitung

A.O. Smith

A.O. Smith CMC/SU-54 Bedienungsanleitung

A.O. Smith

A.O. Smith BFM - 100 Beilage

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung