ACME Color Spot Bedienungsanleitung

COLOR SPOT

COLOR WASH

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. Installation

4. DMX512 Address setting

5. How to control the fixture

6. DMX 512 Connections

7. Fixture Cleaning

Широкий ассортимент оборудования ACME

на www.maxlight.ru

1. Safety Introductions

WARNING

z Please keep this User Manual for future consultation. If you sell the fixture to another

user, be sure that they also receive this instruction booklet.

z Unpack and check carefully there is no transportation damage before using the fixture.

z Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the fixture.

z It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

z Disconnect main power before servicing and maintenance.

z Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only,

but always by taking its base.

z Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is

higher than this.

z In the event of serious operating problem, stop using the fixture immediately. Never try

to repair the fixture by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance

center. Always use the same type spare parts.

z Do not connect the device to any dimmer pack.

z Do not touch any wire during operation and there might be a hazard of electric shock.

z To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain

or moisture.

z The housing must be replaced if they are visibly damaged.

z Do not look directly at the LED light beam while the fixture is on.

z There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact your nearest dealer.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

2. Technical Specifications

¥ Power supply

Input Voltage：AC 100V~240V 50/60HZ

Power consumption：10W

¥ LED

Color Spot：Red 24pcs, Green 33pcs, Blue 33pcs

Color Wash：Red 31pcs, Green 30pcs, Blue 30pcs

¥ Channels

Channel 1 = Red

Channel 2 = Green

Channel 3 = Blue

Channel 4 = Dimmer / Strobe

¥ Dimension：Φ106mm x 130mm

¥ Weight：1 kgs

3. Installation

The fixture can be place on the ground, fix on the wall or under ceiling and clamp on the

truss. Please checkout the voltage before applying power. Do not connect the fixture to an

electrical dimmer system which it could damage the inside electronics.

4. DMX512 Address Setting

1. Each fixture needs to have an address set to receive the data sent by the controller. The

address number is between 0-511 (usually 0 & 1 are equal to 1). The address, also know

as the start channel, is the first channel used to receive instructions the controller.

2. The fixture uses four channels, the next fixture’s will be automatic calculate their own

DMX address, no need to calculate the DMX channels of each fixture in the chain.

(Fixture 1 = 1, Fixture 2 = 5, Fixture 3 = 9, Fixture 4 = 13, Fixture…)

3. No need to turn the fixture off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the fixture on, it will be ready to

receive DMX signal or run the built-in programs.

A. By Auto setting

1. Each fixture needs to have an address set to receive the data sent by the controller. The

address number is between 0-511 (usually 0 & 1 are equal to 1). The address, also know

as the start channel, is the first channel used to receive instructions from the controller.

2. The DMX address of fixture can be set automatically. You have to press the auto

addressing button from the first fixture’s main PC Board. When you hold the button 5secs,

the fixture will be set the DMX address to 1, and the other fixtures of the chain will be set

their own DMX address automatically.

3. The LED fixtures use four channels, the next fixture’s will be automatic calculate their own

DMX address, not need to calculate the DMX channels of each fixture in the chain.

(Fixture 1 = 1, Fixture 2 = 5, Fixture 3 = 9, Fixture 4 = 13, Fixture…)

4. Not need to turn the fixture off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the fixture on, it will be ready to

receive DMX signal or run the built-in programs.

B. By CA-T DMX TESTER

The fixture can be set the DMX address remotely by CA-T DMX TESTER. Please refer to

the CA-T user manual to set the DMX address to the fixture.

C. By Universal DMX controller

z Make sure the DMX cables of all units are connected.

z Connect the first unit to a universal DMX controller.

z Connect all units to the mains so they are switched on.

z Set all DMX-channels on your DMX-controller to zero (value 000).

z Set the DMX-channel, that you want to assign as DMX start address on you projector,

tot maximum (value 255).

z Press the “Auto DMX address” button on the projector shortly.

z If you want to set another projector to the same DMX start address, simply press it’s

“Auto DMX address”, button and it will receive the same address.

z Done!

An example to make things clear:

z We will set the DMX start address of a projector to 106:

z Connect the projector to the DMX-controller as described above and make sure all is

switched on.

z Set all DMX-channels on the controller to zero (000).

z Now set DMX-channel 106 to maximum (255).

z Press the “Auto DMX address” button on the projector shortly.

y Done! Your projector now has DMX address 106!

5. How to control the fixture

Three ways to set-up the DMX address

A. Universal DMX controller

B. Master/Slave operation

C. Easy controller (by CA-8)

A. Universal DMX controller

The fixture can be set the DMX address remotely by universal DMX controller. First, you

need to programming two scenes into a chase, and then link the fixtures to the universal

DMX controller. When you run the chase, all the fixtures of the chain will be set the series

DMX address automatically. If you use a controller with 5 pins DMX connector, you need to

use a 5 to 3 pin adapter. The fixture uses four channels. Please refer to the following

diagram to use your controller to activate the fixture.

B. Master/Slave operation

The fixtures will allow you to link 16 fixtures together and operate without a controller. In

Master/Slave mode, the first fixture will control the others to give an automatic, sound

activated, synchronized light show. This function is good when you want an instant show.

The first unit it’s DMX input cable will have nothing connect it, and the other fixtures will be

set in slave mode automatically. Their DMX input cables connect the last fixture DMX output

cable (daisy chain). Any fixture can act as a Master or as a Slave

C. Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. There

is a terminator for connect the easy controller inside the fixture. By

connecting the cable into DMX IN waterproof cable entry gland to

the CA-8 terminator of the first fixture, you will find that the remote

control on the first fixture will control all the other fixtures for Stand

by, Function and Mode functions.

Blackout To blackout all the fixture

Function Strobe

1.Synchronous

strobe in white

color

2.The same color

chase

3.Different color

strobe

9 Color select

WhiteÎRedÎ

BlueÎPurpleÎ

OrangeÎGreenÎ

YellowÎMagenta

ÎCyan

Color Chase

1. The same color

2. Different color

3. One light chase

4. Two lights chase

5. Four lights chase

Color Fade

1. Fast speed

2. Middle speed

3. Slow speed

Mode Sound 1

(LED OFF)

Manual

(LED ON)

Sound 2

(LED slow blinking)

Auto

(LED fast

blinking)

6. DMX512 Connections

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. Connect the unit together in a “daisy chain” by XLR plug cable from the output of the unit

to the input of the next unit. The cable cannot be branched or split to a “Y” cable.

Inadequate or damaged cables, soldered joints or corroded connectors can easily distort

the signal and shut down the system

2. The DMX output and input connectors are pass-through to maintain the DMX circuit when

no power is connected to the fixture.

3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal

errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a

3-pin XLR-plug and plug it in the DMX-output of the last fixture.

4. Each lighting unit needs to have an address set to receive the data sent by the controller.

The address number is between 0-511 (usually 0 & 1 are equal to 1).

5. 3 pin XLR connectors are more popular than 5 pins XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

7. Fixture Cleaning

The cleaning of internal must be carried out periodically to optimize light output. Cleaning

frequency depends on the environment in which the fixture operates: damp, smoky or

particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.

y Clean with soft cloth using normal glass cleaning fluid.

y Always dry the parts carefully.

y Clean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

Innovation, Quality, Performance

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME LED-BL8 Bedienungsanleitung

ACME

ACME LED-MTX36 HEX Bedienungsanleitung

ACME

ACME E-200 MB MC Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME PAGEANT 300ZR Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME MINI ELLIPSOIDAL 10 Bedienungsanleitung

ACME

ACME LED-920D Bedienungsanleitung

ACME

ACME AE-610 BEAM Bedienungsanleitung

ACME

ACME MP-400Z IP Bedienungsanleitung

ACME

ACME ARAS Bedienungsanleitung

ACME

ACME E-10T WW DXX Bedienungsanleitung

ACME

ACME CP-56U Bedienungsanleitung

ACME

ACME BLINDER LINE 10 IP Bedienungsanleitung

ACME

ACME LED-MB50 Bedienungsanleitung

ACME

ACME LED-7871 Bedienungsanleitung

ACME

ACME Junior Series Bedienungsanleitung

ACME

ACME LED-MS150 Bedienungsanleitung

ACME

ACME GLORY PROFILE Bedienungsanleitung

ACME

ACME UV-9N Bedienungsanleitung

ACME

ACME CW-108 Bedienungsanleitung

ACME

ACME FURY LED RGB Bedienungsanleitung

ACME

ACME SAM-50 Bedienungsanleitung

ACME

ACME FARANDOLE AM-BAR Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung