ACME PAGEANT 300ZR Bedienungsanleitung

User Manual

Please read the instrucon carefully before use

CM-300ZR II

TABLE OF CONTENTS

1. Safety Instructions.................................................................................................. 2

2. Technical Specifications .......................................................................................... 3

3. How To Set The Unit ............................................................................................... 4

3.1 Control Panel.................................................................................................... 4

3.2 Main Function .................................................................................................. 5

3.3 Home Position Adjust ..................................................................................... 13

4. Control By Universal DMX Controller.................................................................... 13

4.1 DMX 512 Connection...................................................................................... 13

4.2 Address Setting............................................................................................... 14

4.3 DMX 512 Configuration .................................................................................. 15

5. Troubleshooting ................................................................................................... 23

6. Fixture Cleaning ................................................................................................... 24

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cables when fixing this unit. DO NOT handle the unit by its head only, always carry by

its base.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature

is higher than this.

Unit surface temperature may reach up to 75 degrees C. DO NOT touch the housing with

bare-hands during its operation. Turn off the power and allow about 15 minutes for the unit to

cool down before replacing or serving.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage may cause electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

Please read the instruction carefully which includes important

information about the installation, usage and maintenance.

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that

the unit is firmly fixed to avoid vibration and slipping while operating and make sure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the fixtures weight. Always use a safety cable that can hold 12 times of the weight of

the fixture when installing.

The equipment must be installed by professionals. It must be installed in a place where is out of

the reach of people and no one can pass by or under it.

2. Technical Specifications

◇Extremely small, fast and powerful LED moving beam.

◇DMX Channels: 14/2 6/3 0 channels mode

◇Operation modes: DMX512

◇Blue LCD display for easy navigation

◇Ring control, outstanding color macro effect

◇Perfect for stage, theatre, TV studio, rental and discotheques

Input Voltage:AC 100V~240V, 50/60Hz 

Power Consumption: 270W

Power Cable Daisy Chain: 4 Fixture Max. (230V, 50Hz)

2 Fixture Max. (130V, 60Hz)



Beam Angel: 10° ~ 60°



LED Source:

Weight:

Dimension:

19 × 15WRGBW LED

9.0Kgs

325 × 189 × 393mm

3. How To Set The Unit

3.1 Control Panel

1234567891011

LED:

1.POWER ON Power On

2.DMX ON DMX input present

3.Display:

Shows the various menus and the selected functions

4. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

5. DMX input:

DMX512 link, use 5-pin XLR cable to link the unit and DMX controller

6. DMX input:

DMX512 link, use 3-pin XLR cable to link the unit and DMX controller

7. DMX output:

DMX512 link, use 5-pin XLR cable to link the next unit

8. DMX output:

DMX512 link, use 3-pin XLR cable to link the next unit

9. Power:

Turn on/off the power

10. Mains input:

Connects to the main power supply.

11. Fuse (T 6.3A):

Protects the unit from over-voltage or short circuit.

3.2 Main Function

To select any of the given functions, press the MENU button until the required function is showing

on the display. Select the function by pressing the ENTER button and the display will blink. Use the

DOWN/UP buttons to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Press and hold the MENU button for about one second or wait for one minute to exit the

menu mode.

The main functions are shown overleaf:

Fixture Setting

Display Setting

Pan Inverse

Tilt Inverse

P/T Feedback

Bl.o. P/T Moving

White Balance

Display Inverse

Backlight Auto Off

Display Warning

Backlight Intensity

Temperature Unit

DMX Functions

View DMX Value

Fixture Test

Fixture Information

Reset Functions

Special Functions

Factory Setting

Fixture Maintenance

Interval

Remain Time

Pan /Tilt

Zoom

All

Au to Test

Fixture use time

Fireware Version

Manual Test

DMX Channel Mode

DMX Address

Auto

Fast

Square Law

Linear

Low

Smooth

Inverse Squ.

S-curve

Cooling Mode

Dimmer Speed

Dimmer Curve

English

Chinese

Language

DMX Functions

Enter MENU mode, select DMX Functions, press the ENTER button to confirm, use the UP/DOWN

button to select DMX Address, DMX Channel Mode or View DMX Value.

DMX Address

To select DMX Address, press the ENTER button to show the DMX ADDRESS on the display.

Use the UP/DOWN button to adjust the address from 001to 512, press the ENTER button to setup.

Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

DMX Channel Mode

To select DMX Channel Mode, press the ENTER button to show the DMX CHANNEL MODE on

the display. Use the UP/DOWN button to select Mode1 (14), Mode2 (26) or Mode (30), and press

the ENTER button to setup. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

View DMX Value

To select View DMX Value, press the ENTER button to show the VIEW DMX VALUE on the

display. Use the UP/DOWN button to view the DMX channel values. Press the MENU button back

to the last menu or let the unit idle one minute to exit menu mode.

Fixture Setting

Enter MENU mode, select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN

button to select Pan Inverse, Tile Inverse, P/T Feedback,BL.O. P/T Moving, White Balance,

Cooling Mode,Dimmer Curve or Dimmer Speed.

Pan Inverse

To select Pan Inverse, press the ENTER button to show the PAN INVERSE on the display. Use

the UP/DOWN button to select No (normal) or Yes (pan inverse), press the ENTER button to setup.

Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Tilt Inverse

To select Tilt Inverse, press the ENTER button to show the TILT INVERSE on the display. Use

the UP/DOWN button to select No (normal) or Yes (tilt inverse), press the ENTER button to setup.

Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

P/T Feedback

To select P/T Feedback, press the ENTER button to show the PAN/TILT FEEDBACK on the

display. Use the UP/DOWN button to select No (Pan or tilt’s position will not feedback while out

of step) or Yes (Feedback while pan/tilt out of step), press the ENTER button to setup. Press the

MENU button back to the last menu or let the unit idle one minute to exit menu mode.

BL.O. P/T Moving

To select BL.O. P/T Moving, press the ENTER button to show the BLACKOUT WHILE PAN/TILT

MOVING on the display, use the UP/DOWN button to select No (normal while pan/tilt moving) or

Yes (blackout while pan/tilt moving), press the ENTER button to setup. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

White Balance

To select White Balance, press the ENTER button to show the WHITE BALANCE on the display, use

the UP/DOWN button to select Red, Green or Blue. Once selected, press the ENTER button to

confirm, and use the UP/DOWN button to adjust the value from 125 to 255, press the ENTER

button to setup. Press the MENU button back to the last menu or let the unit idle one minute to

exit menu mode.

Cooling Mode

To select Cooling Mode, press the ENTER button to show the COOLING MODE on the display.

Use the UP/DOWN button to select Auto (Normal) or Low (Low speed). Once selected, press the

ENTER button to setup. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display,

use the UP/DOWN button to select Linear, Square Law, Inverse Squ. or S-curve. Once selected,

press the ENTER button to store. Press the MENU button back to the last menu or let the unit idle

one minute to exit menu mode.

Linear: The increase in light intensity appears to be linear as DMX value is increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

S-cure: Light intensity control is finger at low levels and high levels and coarser at medium levels.

Dimmer Speed

To select Dimmer Speed, press the ENTER button to show the DIMMER SPEED on the display.

Use the UP/DOWN button to select Fast or Smooth. Once selected, press the ENTER button to

setup. Press the MENU button back to the last menu or let the unit idle one minute to exit menu

mode.

Display Setting

Enter MENU mode, select Display Setting, press the ENTER button to confirm, use the UP/DOWN

button to select Display Inverse, Backlight Auto Off, Backlight Intensity ,Temperature unit,

Display Warning or Language.

Display Inverse

To select Display Inverse, press the ENTER button to show the DISPLAY INVERSE on the

display. Use the UP/DOWN button to select No (normal) or Yes (display inverse). Once selected,

press the ENTER button to store. Press the MENU button back to the last menu or let the unit idle

one minute to exit menu mode.

Backlight Auto Off

To select Backlight Auto Off, press the ENTER button to show the BACKLIGHT AUTO OFF on

the display. Use the UP/DOWN button to select No (display always on) or Yes (display goes off one

minute after exiting menu mode). Once selected, press the ENTER button to confirm and store.

Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME CW-108 Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME Dotline 360 Bedienungsanleitung

ACME

ACME Solaris CM-S6 Bedienungsanleitung

ACME

ACME Stage Panel 1080 Bedienungsanleitung

ACME

ACME LS-608 RGB Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME LP-TS200 CW Bedienungsanleitung

ACME

ACME CP-56U Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME MH-575S Bedienungsanleitung

ACME

ACME LED-MB50 Bedienungsanleitung

ACME

ACME LED-245 II Bedienungsanleitung

ACME

ACME LED-MTX36 HEX Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME LED-MS50A Bedienungsanleitung

ACME

ACME XP-1200F Bedienungsanleitung

ACME

ACME LED?7TC Bedienungsanleitung

ACME

ACME E-10C WW DXX Bedienungsanleitung

ACME

ACME BLINDER LINE 10 IP Bedienungsanleitung

ACME

ACME MP-90 RGBW Bedienungsanleitung

ACME

ACME LED-635S Bedienungsanleitung

ACME

ACME TB-1010QW II Bedienungsanleitung

ACME

ACME RAYZOR HYBRID XA-100 BSW Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung