ACME LED-MB50 Bedienungsanleitung

23-

Innovation, Quality, Performance

LED BEAM 300

LED-MB50

UserGuide

Professional Entertainment Technology

22-

EC Declaration of Conformity

We declare that our products (lighting equipments) comply with the

following specification and bears CE mark in accordance with the

provision of the Electromagnetic Compatibility (EMC) Directive

89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

21-

6. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

Fresnel Lens:

Clean the lens with neutral soap and water, and then dry it with soft cloth. Be aware that

alcohol or other detergent could cause damage to lens. Please note the lens would be burnt

yellow or cracked after three-month use of average 8 hours per day, which can reduce the

output in some degree. The lens is consumable with a warranty of three months only.

Please change with genuinely new lens when necessary.

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. How To Set The Unit

4. How To Control The Unit

5. Troubleshooting

6. Fixture Cleaning

1. Safety Instruction

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yDisconnect main power before replacement or servicing.

yMake sure there is no flammable materials close to the unit while operating as it is fire

hazard.

yUse safety cable when fixes this unit. Don’t handle the unit by taking its head only, but

always by taking its base.

yMaximum ambient temperature is ta: 40℃. Don’t operate it where the temperature is

higher than this.

yUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during

its operation. Turn off the power and allow about 15 minutes for the unit to cool down

before replacing or serving.

yIn the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

yDo not touch any wire during operation as high voltage might be causing electric shock.

Warning

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

yDo not open the unit within five minutes after switching off.

Please read carefully the instruction, which includes important information

about the installation, usage and maintenance.

20-

Not used.

5. Troubleshooting

Following are a few common problems that may occur during operation. Here are

some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the unit or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the

master/ slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Make sure the unit does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition

19-

4.5 DMX512 Connection

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm

1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it

in the DMX-output of the last unit.

3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to

the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is

a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,

when one of the units’ power is disconnected.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin 4/Pin 5:

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. And make sure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

2. Technical Specification

yLED BEAM 300 that creates extremely powerful beam

yThree operation modes: DMX, Master/Slave, Sound Active

yDMX channels: 15/16

yRotating Gobo wheel: 6 gobos + open

yColor Wheel: 7 colors + open

y3 facet rotating, indexable and replaceable prism

yAuto focus

yBeam angle: 4°

yOptional CA-8 easy controller or CA-9 RTX (wireless easy control kit) for instant lighting

shows

yLinear dimmer 0~100% and variable strobe

Voltage: 230V, 50Hz

Power consumption: 180W

For power supply, do not connect in series more than 2 units, use

another mains supply for the next units.

Light source: 1×50W White LED

Dimension: 419.7 X 311 X 618.7 mm

ΦRotating gobo =19mm

Weight: 12.8 kg

3. How To Set The Unit

3.1 Control panel

Display

To show the various menus and the selected functions

LED

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

18-

GOBO:

17-

16 channel modes:

Button

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

Only for remote control

Connecting with CA-8/CA-9/CA-9RTX to control the unit for Stand by, Function and Mode

function.

Mains input

Connect to power supply.

Mains output

Connect to supply power for the next unit.

DMX input/output

For DMX512 link, use 3/5-pin XLR cable to link the unit together.

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected,

press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

The main functions are showing below:

16-

15-

4.4 DMX 512 Configuration

15 channel modes:

DMX Address

Select DMX Address, press ENTER button to confirm, the present address will blink on the

display. Use UP and DOWN button to adjust the address from 1to 512. Once the address

has been selected, press the ENTER button to setup, to go back to the functions without any

change press the MENU button again. Hold and press the MENU button about one second

or wait for one minute to exit the menu mode.

Channel Mode

Select Channel Mode, press ENTER button to confirm, present mode will blink on the

display. Use DOWN and UP button to select the 15 Chan (15 Channel Mode) or 16 Chan

(16 Channel Mode) mode. Once the mode has been selected, press the ENTER button to

setup, to go back to the functions without any change press the MENU button again. Hold

and press the MENU button about one second or wait for one minute to exit the menu mode.

Show Mode

Select Show Mode, press ENTER button to confirm, present mode will blink on the display.

Use DOWN and UP button to select the Show 1 or Show 2 or Show 3 or Show 4 mode.

Once the mode has been selected, press the ENTER button to setup, to go back to the

functions without any change press the MENU button again. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

Split Color Mode

Select Split Color Mode, press ENTER button to confirm, present mode will blink on the

display. Use DOWN and UP button to select the Yes (Split Color mode) or No (normal)

mode. Once the mode has been selected, press the ENTER button to setup, to go back to

the functions without any change press the MENU button again. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

Slave Mode

Select Slave Mode, press ENTER button to confirm, present mode will blink on the display.

Use DOWN and UP button to select the Slave 1 (normal) or Slave 2 (2 light show) mode.

Once the mode has been selected, press the ENTER button to setup, to go back to the

functions without any change press the MENU button again. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

Black Out

Select Slave Mode, press ENTER button to confirm, present mode will blink on the display.

Use DOWN and UP button to select the Yes (yes blackout) or No (no blackout) mode. Once

the mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Sound State

Select Sound State, press ENTER button to confirm, present mode will blink on the display.

Use DOWN and UP button to select the On (sound on) or Off (sound off) mode. Once the

mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Sound Sense

Select Sound Sense, press ENTER button to confirm, present mode will blink on the display.

Use DOWN and UP button to select the 0…100 mode. Once the mode has been selected,

press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

Pan Inverse

Select Pan Inverse, press ENTER button to confirm, present mode will blink on the display.

Use DOWN and UP button to select the Yes (pan inversion) or No (normal) mode. Once the

mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Tilt Inverse

Select Pan Inverse, press ENTER button to confirm, present mode will blink on the display.

Use DOWN and UP button to select the Yes (tilt inversion) or No(normal) mode. Once the

mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

14-

4.2 Easy Controller

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit, you will find that the remote controller on the first unit will

control all the other units in Stand by, and Mode selection.

Stand By Blackout the unit

Function 1. Sync. Strobe

2. Async strobe

3. Sound Strobe

Show

1-4

1. Press to select color

2. Hold to select gobo

Mode Sound (LED OFF) Show (LED

Slow Blinking)

LED ON

4.3 DMX Controller

By using a universal DMX controller to control the units, you will need to set DMX address

from 1 to 512 so that the units can receive DMX signal.

Press the MENU button up to when the DMX Address is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to change the DMX512

address. Once the address has been selected, press the ENTER button to setup, to go back

to the functions without any change press the MENU button again. Hold and press the

MENU button about one second or wait for one minute to exit the menu mode.

Please refer to the following diagram to address your DMX512 channel for the first 4 units：

Channel mode Unit 1

Address

Unit 2

Address

Unit 3

Address

Unit 4

Address

15channels 1 16 31 46

16channels 1 17 33 49

Dieses Handbuch passt für folgende Modelle

Andere ACME DJ-Equipment Handbücher

ACME

ACME CP-21TC Bedienungsanleitung

ACME

ACME DVS-2500 Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME Ellipsoidal Bedienungsanleitung

ACME

ACME LED-MTX25 IP Bedienungsanleitung

ACME

ACME Theatre LED Colour Flood Bedienungsanleitung

ACME

ACME Color Par 36 Bedienungsanleitung

ACME

ACME MP-90 RGBW Bedienungsanleitung

ACME

ACME MACE Bedienungsanleitung

ACME

ACME MINI ELLIPSOIDAL 10 Bedienungsanleitung

ACME

ACME Solaris CM-S6 Bedienungsanleitung

ACME

ACME Stage Blinder P4 Bedienungsanleitung

ACME

ACME LED?7TC Bedienungsanleitung

ACME

ACME XP-1000WZ Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME Festival LED-787 Bedienungsanleitung

ACME

ACME BP-40 QW S DXX Bedienungsanleitung

ACME

ACME THUNDERBOLT Bedienungsanleitung

ACME

ACME CA-DD12 II Bedienungsanleitung

ACME

ACME LED?7TC Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME PAGEANT 300ZR II Bedienungsanleitung

ACME

ACME Ellipsoidal E-300 D2550 Bedienungsanleitung

ACME

ACME XP-1200F Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung