ACME LED-BR10 Bedienungsanleitung

LED BARREL

LED-BR10

User Manual

Professional Entertainment Technology

Широкий ассортимент оборудования ACME

на www.maxlight.ru

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Installation

4. How to Control the Unit

4.1 Control Panel

4.2 Master/Slave operation

4.2 Easy controller

4.4 Universal DMX controller

5. DMX 512 Configuration

6. DMX 512 Connection

7. Trouble Shooting

8. Fixture Cleaning

1. Safety Instruction

WARNING

yPlease keep this User Manual for future consultation. If you sell the unit to another

user, be sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only and use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yDisconnect mains power before fuse replacement or servicing.

yReplace fuse only with the same type.

yMake sure there are not flammable materials close to the unit while operating as it is

fire hazard.

yUse safety cable when fixes this unit.

yMaximum ambient temperature is TA: 40 ℃and don’t operate it where the

temperature is higher than this.

yUnit surface temperature may reach up to 60℃. Don’t touch the housing bare-hand

during its operation.

yThere are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact the nearest authorized technical assistance center and always use the

same type spare parts. .

yDon’t connect the device to any dimmer pack or power pack.

yDo not look directly at the LED light beam while the fixture is on.

yThe housing must be replaced if they are visibly damaged.

yDo not touch any wire during operation as high voltage might be causing electric

shock.

Please read the instruction carefully which including important

information about the installation, operation and maintenance.

2. Technical Specification

yIt can be operated by DMX512 control or can be used as an individual unit without

controller.

yPlease use a 3 pin XLR cable/plug when link in master/slave mode.

ySmooth 0-100% dimming, and variable strobe speed.

y5 Channels

Channel 1 = Pan

Channel 2 = Barrel

Channel 3 = Strobe

Channel 4 = Color

Channel 5 = Dimmer

yVoltage: AC 100-240V~50/60Hz

yFuse: T 2A

yLED: 1 x 10W LED

yPower Consumption: 23W

yDimension: 311 x 135 x 170 mm

yWeight: 3.4kg

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

For power supply, do not connect in series much more than 20 units, use

another mains supply for next 20 units.

4. How To Control The Unit

4.1 Control Panel

○

1Dip switches：For different function setting.

○

2Only for remote control: Connecting with CA-8/CA-9/CA-9RTX to control the unit for

Stand by, Function and Mode function.

○

3DMX output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

○

4DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal.

○

5Power：Connect to supply mains power.

○

6 Microphone: Receives the sound to control the unit

4.2 Master/Slave Operation

The unit can be linked together in daisy chain as many as you need in master/slave mode

to perform the great built-in pre-programmed lighting shows triggered by music.

In Master/Slave mode refer to the DMX settings below:

Master unit: DMX start address MUST be set to 001. (First DIP switch = ON, all others

are OFF)

Slave units: DMX start address may have any value but NOT 001 (example: set the first 3

DIP switches to ON)

2-Light Show

Dipswitch 10 ”off” means the unit works normally and “on” means 2-Light show. In order to

create a great light show, you can set dip switch 10 ”on” on any unit that is linking to the

master unit to get contrast movement to the master unit, even if you have two units only.

Dipswitch 10 on the first (Master) unit is no use for the 2-light show as it is the master unit

that operates the light show.

4.3 Easy Controller (by CA-8/CA-9/CA-9RTX)

The easy remote control is used only in master/slave mode. By

connecting to the 4-pin jack of the first unit, you will find that the

remote controller on the first unit will control all the other units for

Stand by, Function and Mode selection

4.4 Universal DMX Controller

When using a universal DMX controller to control the chain of units, you have to set DMX

address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal.

The dip switch 10 is used to choose channel mode. Please refer to the following diagram

to know how to address your DMX 512 system in the binary code.

DMX 512 Address Chart:

Dip-switches # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9 #10

Value 1 2 4 8 16 32 64 128 256 2-Light show

•Examples:

Unit 1：dip / on: #1 (=1)

Unit 2：dip / on: #2, #3 (2+4=6)

Unit 3：dip / on: #1, #2, #4 (1+2+8=11)

Unit 4：dip / on: #5 (=16)

Stand by Blackout the unit

Function

1. Synchronous Strobe in

white

2. Sound strobe in white

3. Sound Strobe in color

Select Color Select Show

1-6

Mode Strobe (LED OFF) Show (LED ON) LED blinking

Dip switches settingChannel

1 2 3

5 6 7 8 910

1 2 3 4

8 9 10

1 2 3 4 5 6 7 8 9 10

5. DMX 512 Configuration

5 Channel mode

DMX Configuration

Pan Barrel Strobe Color Dimmer

000-009

010-120

121-134

135-245

246-255

Stop

Rotation

Fast

Slow

Stop

Fast

Slow

Rotation

Stop

000-009

Open

008-131

132-139

Open

140-181

Fast close

slow open

182-189

Open

190-231

Slow close

fast open

Open

232-239

Random

strobe

Open

240-255

000-007 Black Out

008-024 Red

025-041 Green

042-057 Blue

058-074 White

075-091 Red+Green

092-107 Red+Blue

108-124 Red+White

125-141 Green+Blue

142-157 Green+White

158-174 Blue+White

175-191 Red+Green+Blue

192-207 Red+Green+White

208-224 Red+Blue+White

225-240 Green+Blue+White

241-255 Red+Green+Blue+White

6. DMX 512 Connection

The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels.

1.If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120

ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug

and plug it in the DMX-output of the last unit.

3.Connect the unit together in a ‘daisy chain’by XLR plug from the output of the unit

to the input of the next unit. The cable can not be branched or split to a ‘Y’ cable.

DMX 512 is a very high-speed signal. Inadequate or damaged cables, solder

joints or corroded connectors can easily distort the signal and shut down the

system.

4.The DMX output and input connectors are pass-through to maintain the DMX

circuit, when power is connected to the unit.

5.Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-512 (usually 0 & 1 are equal to 1).

6.The end of the DMX 512 system should be terminated to reduce signal errors.

7.3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

Pin4/5:Notused.

7. Troubleshooting

Following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The fixture does not work, no light

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the fixture or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some fixtures don’t respond to the easy controller

1. Check the LED for the response of the master/ slave mode signal.

2. Check if the unit is receiving DMX signal and cut it off.

D. No response to the sound

1. Make sure the fixture does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone.

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

8. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause

greater accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

EC - Declaration of Conformity

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

Innovation, Quality, Performance

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME Color Fusion CF-805 Bedienungsanleitung

ACME

ACME E-200 MB MC Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME MP-400Z IP Bedienungsanleitung

ACME

ACME GENESIS COLOR II Bedienungsanleitung

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME MH-275R Bedienungsanleitung

ACME

ACME SPLENDOR 90 Bedienungsanleitung

ACME

ACME LED-MTX36 HEX Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME LED-245 II Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME CA-DD12 II Bedienungsanleitung

ACME

ACME LED-RC8 Bedienungsanleitung

ACME

ACME E-10T WW DXX Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME E-10C WW DXX Bedienungsanleitung

ACME

ACME CP-21TC Bedienungsanleitung

ACME

ACME 04XOZONE Bedienungsanleitung

ACME

ACME LED-BL8 Bedienungsanleitung

ACME

ACME Genesis move 25R Bedienungsanleitung

ACME

ACME FARANDOLE AM-BAR Bedienungsanleitung

ACME

ACME E-40D TC DXX Bedienungsanleitung

ACME

ACME RAYZOR HYBRID XA-100 BSW Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung