ACME GENESIS COLOR II Bedienungsanleitung

15-

Innovation, Quality, Performance

GENESIS COLORⅡ

LED-CC 20Ⅱ

User Guide

Professional Entertainment Technology

14-

EC Declaration of Conformity

We declare that our products (lighting equipments) comply

with the following specification and bears CE mark in

accordance with the provision of the Electromagnetic

Compatibility (EMC) Directive 89/336/EEC.

EN55103-1:1996; EN55103-2:1996;

EN61000-3-2:2006; EN:61000-3-3:1995+A1:2001+A2:2005.

Harmonized Standard

EN60598-1:2004; EN60598-2-4:1997.

Safety of household and similar electrical appliances

Part 1: General requirements

13-

6. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. How To Set The Unit

4. How To Control The Unit

5. Troubleshooting

6. Fixture Cleaning

1. Safety Instruction

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yDisconnect main power before replacement or servicing.

yMake sure there is no flammable materials close to the unit while operating as it is fire

hazard.

yUse safety cable when fixes this unit.

yMaximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is

higher than this.

yUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during

its operation. Turn off the power and allow about 15 minutes for the unit to cool down

before replacing or serving.

yIn the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

yDo not touch any wire during operation as high voltage might be causing electric shock.

Warning

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

yDo not open the unit within five minutes after switching off.

Please read carefully the instruction, which includes important information

about the installation, usage and maintenance.

12-

5. Troubleshooting

Following are a few common problems that may occur during operation. Here are

some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the unit or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the

master/ slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Make sure the unit does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition

11-

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm

1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it

in the DMX-output of the last unit.

3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to

the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is

a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,

when power is disconnected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

Pin 4/5: Not used.

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of 20

kg for each unit.

2. Technical Specification

•The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together

in master/slave connection, as many as required and run by built-in program chase

sequences automatically or by sound activation through an internal microphone to create

an intelligent effect.

•It can be operated by DMX 512 control or can be used as an individual unit without a

controller.

•Features different preprogrammed chase patterns.

•Please use a cable when connecting units together.

•Accurate focusable optics system and ultra smooth stepping motors.

•Fan cooled.

•Voltage：AC 230V/240V/250V- 50HZ~120V-60HZ

•Fuse: T 2A

•Power consumption: 31W

•Light source: 10W CREE LED

•Dimension: 206 x 199 x 187 mm

•Weight: 2.4 kg

3. How To Set The Unit

3.1 Control Panel

○

1Display：To show the various menus and the selected functions

LED

○

2DMX On DMX input present

○

3 MASTER On Master Mode

○

4 SLAVE On Slave Mode

○

5 SOUND Flashing Sound activation

Button

○

6MENU To select the programming functions

○

7DOWN To go backward in the selected functions

○

8UP To go forward in the selected functions

○

9ENTER To confirm the selected functions

○

10Sensitivity: To adjust the sound receiving sensitivity

○

11Only for remote control: By connect to the 1/4’’ microphone jack to control the unit for

Stand by, Function and Mode function.

○

12DMXoutput: For DMX512 link, use 3-pin XLR plug cable to link to the next unit.

○

13DMX input: For DMX512 link, use 3-pin XLR plug cable to input DMX signal.

○

14Mains input：IEC socket and integrated fuse holder, connect to main power cable.

10-

4.4 DMX 512 Configuration

4.5 DMX512 Connection

The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.

4.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other units to

give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show.

2-light show

In (slave mode), means the unit works normally and means

2-light show. In order to create a great light show, you can set on the second unit to

get contrast movement to each other, even if you have two units only.

4.2 Easy Controller

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit, you will find that the remote control on the first unit will

control all the other units functions press the MENU button again.

Stand By Blackout the unit

Function 1. Sync. Strobe

2. Async strobe

3. Sound Strobe

Select Color

Mode Sound (LED OFF) Show (LED On)

4.3 DMX Controller

An universal DMX controller to control the units, you have to set DMX address from 1 to 512

channel so that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to change the

DMX512 address. Once the address has been selected, press and keep ENTER

button pressed up to when the display stops blinking or storing automatically 8

seconds later. To go back to the functions without any change press the MENU

button again. If you use please refer to the following diagram to address your

DMX512 channel for the first 4 units.

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected,

press the ENTER button to setup or it will automatically return to the main functions without

any change after idling 8 seconds. To go back to the functions without any change press the

MENU button. The main functions are showing below:

DMX 512 Address Setting

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press the ENTER button to setup or automatically

return to the main functions without any change after 8 seconds. To go back to the functions

without any change press the MENU button again.

Slave Mode

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(normal) or (2 light show) (3 light show) (4 light show) mode.

Once the mode has been selected, press the ENTER button to setup or automatically return

to the main functions without any change after 8 seconds. To go back to the functions

without any change press the MENU button again.

Sound Mode

Press the MENU button until the is showing on the display. Pressing ENTER button

and the display will blink. Use DOWN and UP button to select the (sound on) or

(sound off) mode. Once the mode has been selected, press the ENTER button to

setup or automatically return to the main functions without any change after 8 seconds. To

go back to the functions without any change press the MENU button again.

Blackout Mode

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(yes blackout) or (no blackout) mode. Once the mode has been selected, press the

ENTER button to setup or automatically return to the main functions without any change

after 8 seconds. To go back to the functions without any change press the MENU button

again.

Led Display

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(Led on) or (Led off) mode. Once the mode has been selected, press the ENTER

button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the MENU button again.

Inversion

Press the MENU button up to when the is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the

(normal) or (inversion) mode. Once the mode has been selected, press the ENTER

button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the MENU button again.

Auto Test

Press the MENU button up to when the is blinking on the display. Pressing

ENTER button and the display will run self-test by built-in program. To go back to the

functions press the MENU button again.

Temperature Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the temperature of the unit. To go back to the functions

press the MENU button again.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing

ENTER button and the display will show the number of working hours of the unit.

To go back to the functions press the MENU button again.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the MENU button again.

Reset

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and all channels of the unit will return to their standard position. To go back to the

functions without any change press the MENU button again.

4. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By universal DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will show on the

display and move all the motors to their ‘home’ position and you may hear some noises for

about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in

programs.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME LED-256D RGB Bedienungsanleitung

ACME

ACME Ellipsoidal 10 DMX Bedienungsanleitung

ACME

ACME RAYZOR HYBRID XA-100 BSW Bedienungsanleitung

ACME

ACME AE-610 BEAM Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME XP-1000WZ Bedienungsanleitung

ACME

ACME SAMBA Color Bedienungsanleitung

ACME

ACME LED-RC8 Bedienungsanleitung

ACME

ACME LED-MS150 Bedienungsanleitung

ACME

ACME FURY LED RGB Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME LED-635S Bedienungsanleitung

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME Theatre LED Colour Flood Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME XP-1200F Bedienungsanleitung

ACME

ACME LS-608 RGB Bedienungsanleitung

ACME

ACME Color Fusion CF-805 Bedienungsanleitung

ACME

ACME MP-90 RGBW Bedienungsanleitung

ACME

ACME MH-275R Bedienungsanleitung

ACME

ACME MH-600A Mobile Color Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME LED-PAR 100 WW/CW Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung