ACME LP-F2000 VW Bedienungsanleitung

LP-F2000 VW

User Manual

Please read the instructions carefully before use

CONTENTS

1. Safety Introductions.............................................................................................. 2

2. Technical Specifications......................................................................................... 3

3. How To Set The Fixture ......................................................................................... 4

3.1 Control Panel................................................................................................... 4

3. 2 The Plate for Barn Door Installation ............................................................... 5

4. How To Control The Unit..................................................................................... 10

4.1 Master/Slave Function .................................................................................. 10

4.2 DMX Controller ............................................................................................. 10

4.3. DMX512 Configuration................................................................................. 11

4.4. DMX512 Connections................................................................................... 14

5. Troubleshooting .................................................................................................. 15

6. Fixture Cleaning .................................................................................................. 15

1. Safety Introductions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cables when fixing this unit.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature

is higher than this.

Turn off the power and allow about 15 minutes for the unit to cool down before servicing.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Make sure that the structure to which

you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be installed by professionals. It must be fixed at a place where is out of the

reach of people and no one pass by or under it.

2. Technical Specifications

Power Voltage: AC 100 ~ 240V, 50/60Hz

Power Consumption: 199W

Light Sources: 480pcs CW + 480pcs WW LED

Color Temperature: 3200±150K

5600±150K

Beam angle: 130°

CRI

：

≥94

Weight: 13Kgs

Dimension: 668 x 491.4 x 147.5mm

550

668

127.5

147.5

491.4

3. How To Set The Fixture

3.1 Control Panel

1. ETHERNET: Connect with the multimedia and use software to control the units via ArtNet;

2. DMX IN/OUT : For DMX 512 link, use 5-pin XLR cable to link the unit to a DMX controller or the

next unit and output DMX signal;

3. Battery DC48V: Connects to external battery;

4. Fuse (T5A): To protect the unit from damage of over current;

5. Mains In: Connects to mains supply power;

6. Color Temperature Knob: Adjust the color temperature;

7. Dimmer Knob: Adjust the dimmer;

8. Button:

MENU To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER To confirm the selected functions

9. Display: Shows the various menus and the selected functions.

3. 2 The Plate for Barn Door Installation

At first, please push the barn door by hand.

Screw

Secondly, please put the Barn Door into the unit, to fasten the screws of the slot, then finish the

barn door installation.

3.3 Main Function

To select any of the given functions, press the MENU button up to the required selection as shown

on the display. Select the function with the ENTER button and the display will blink. Use the

DOWN/UP buttons to change the mode. Once the required mode has been selected, press the

ENTER button to confirm. To go back to the main functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the current mode.

The main functions are shown below:

DMX Address

Channel Mode

2 Channel

DMX Setting A Setup

-Net

Slave Mode

Slave

Master

Dimmer Curve Square Law Curve

Linear Curve

S Curve

DMX State

Display Setting

Backlight Auto Off

Contrast Ratio

Display Inverse

White Balance

100

Firmware Version

Fixture Time

IP Address

Net

Sub-Net

255

Universe

3 CA hannel

Invert Square Law Curve

immer Speed

Smooth

ast

512

4 ha nelC n

5 Cha neln

3 CB hannel

6 ha nelC n

Blackout

Master Slave

Hold

100

Language

English

Chinese

Manual Mode

255

DMX Setting

Select the DMX Setting, press the ENTER button to confirm. Use the UP and DOWN button to

select DMX Address, Art-Net Setup or Channel Mode.

DMX Address

Select the DMX Address, press the ENTER button to confirm, the display will show the present

address. Use the UP and DOWN button to select 1to 512, press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Art-Net Setup

Select the Eth-Net Address, press the ENTER button to confirm. Use the UP and DOWN button

to select the address for EtherNet IP Setup or ArtNet Port Setup,press the ENTER button to set

the value for these items. Press the MENU button back to the last menu or idling 30 seconds to

exit menu mode.

Channel Mode

Select the Channel Mode, press the ENTER button to confirm, the display will show the present

channel mode. Use the UP and DOWN button to select 2 Channel, 3A Channel, 3B Channel, 4

Channel, 5 Channel or 6 Channel, press the ENTER button to store. Press the MENU button

back to the last menu or idling 30 seconds to exit menu mode.

Dimmer Speed

Select the Dimmer Speed, press the ENTER button to confirm, use the UP and DOWN button to

select the Fast or Smooth mode, press the ENTER button to store. Press the MENU button back to

the last menu or idling 30 seconds to exit menu mode.

Dimmer Curve

Select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display. Use

the DOWN/UP button to select the Mode 1,Mode 2, Mode 3 or Mode 4. Once the dimmer mode

has been selected, press the ENTER button to setup, to go back to the functions without any

change press the MENU button again. Press and hold the MENU button for about one second or

wait for one minute to exit the menu mode.

Mode 1(Optically Linear):

The increase in light intensity appears to be linear as DMX value is increased.

Mode 2(Square Law):

Light intensity control is finer at low levels and coarser at high levels.

Mode 3(Inverse Square Law):

Light intensity control is coarser at low levels and finger at high levels.

Mode 4(S-cure):

Light intensity control is finger at low levels and high levels and coarser at medium levels.

Slave Mode

Select the Slave Mode, press the ENTER button to confirm, use the UP and DOWN button to

select the Master or Slave mode, press the ENTER button to store. Press the MENU button back to

the last menu or idling 30 seconds to exit menu mode.

DMX State

Select DMX State, press the ENTER button to confirm, the present mode will blink on the display,

use the UP and DOWN button to select Master Slave, Blackout or Hold,press the ENTER button to

store. Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

White Balance

Select White Balance,press the ENTER button to confirm, the present mode will blink on the

display, use the UP and DOWN button to select WW or CW and adjust the value from 50 to 100,

press the ENTER button to store. Press the MENU button back to the last menu or idling 30

seconds to exit menu mode.

Display Setting

Select Display Setting, press the ENTER button to confirm, use the UP and DOWN button to select

Contrast Ratio, Backlight Auto off ,Display Inverse or Language.

Contrast Ratio

Select Contrast Ratio, press the ENTER button to confirm, the present mode will blink on the

display, use the UP and DOWN button to adjust from 1 to 30,press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Backlight Auto Off

Select Backlight Auto Off, press the ENTER button to confirm, the present mode will blink on

the display, use the UP and DOWN button to select No or Yes,press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Display Inverse

Select Display Inverse, press the ENTER button to confirm, the present mode will blink on the

display, use the UP and DOWN button to select No or Yes,press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Language

Select Language, press the ENTER button to confirm, the present mode will blink on the display,

use the UP and DOWN button to select Chinese or English,press the ENTER button to store.

Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Manual Mode

Select Manual Mode, press the ENTER button to confirm, the present mode will blink on the

display, use the UP and DOWN button to select the WW or CW,press the ENTER button and use

the UP and DOWN button to adjust the value from 0 ~ 255, press the ENTER button to store. Press

the MENU button back to the last menu or idling 30 seconds to exit menu mode.

Fixture Information

Select Fixture Information, press the ENTER button to confirm, use the UP and DOWN button to

select Fixture Time or Firmware Version.

Fixture Time

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME ORION XP-260 BEAM Bedienungsanleitung

ACME

ACME CB-16FC Bedienungsanleitung

ACME

ACME UV-9N Bedienungsanleitung

ACME

ACME LED-Exercet Bedienungsanleitung

ACME

ACME LED?7TC Bedienungsanleitung

ACME

ACME ELLIPSOIDAL E-300 Bedienungsanleitung

ACME

ACME Dotline360 TB-1230 QW Bedienungsanleitung

ACME

ACME E-10T WW DXX Bedienungsanleitung

ACME

ACME MH-575S Bedienungsanleitung

ACME

ACME LS-608 RGB Bedienungsanleitung

ACME

ACME 04XOZONE Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME CA-DD12 II Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME SPLENDOR 90 Bedienungsanleitung

ACME

ACME Dragonfly Quad Bedienungsanleitung

ACME

ACME Festival LED-787 Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME PAGEANT 300ZR Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME iMove 50SR Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung