ACME IMove 50SR Bedienungsanleitung

iMove 50SR

LED-MS50A

UserGuide

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. How To Set The Unit

4. How To Control The Unit

5. Troubleshooting

6. Fixture Cleaning

1. Safety Instruction

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be sure that they

also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power requirements

of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces.

Be sure that no ventilation slots are blocked.

yDisconnect main power before replacement or servicing.

yMake sure there is no flammable materials close to the unit while operating as it is fire hazard.

yUse safety cable when fixes this unit. Don’t handle the unit by taking its head only, but always by taking

its base.

yMaximum ambient temperature is ta: 40℃. Don’t operate it where the temperature is higher than this.

yUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during its operation.

Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving.

yIn the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the

nearest authorized technical assistance center. Always use the same type spare parts.

yDo not touch any wire during operation as high voltage might be causing electric shock.

Warning

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

yDo not open the unit within five minutes after switching off.

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs

yourself. In the unlikely event your unit may require service, please contact your nearest dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed

to avoid vibration and slipping while operating. And make sure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of

people and has no one pass by or under it.

2. Technical Specification

yGenesis Move 50 is the combination of the latest high powered LED technology, excellent optics and

great features.

yDMX control: 15/16 channels.

Please read carefully the instruction, which includes important information

about the installation, usage and maintenance.

y3 operation modes: DMX, Master/Slave, SoundActivation.

yGreat built-in lighting programs under master/slave mode triggered by music.

yOptional CA-8 easy controller or CA-9 RTX (wireless easy control kit) for instant lighting shows.

yRotating gobo wheel with 7 gobos plus white, fixed gobo wheel with 8 gobos plus open.

yColor wheel with 7 colors plus white.

yPan 540°; Tilt 270°.

yAutomatic Pan/Tilt position correction.

ySmooth 0~100% dimming and variable strobe speeds.

yIndexable, replaceable 3-facet rotating prism.

yAuto focus.

yBeam angle: 17°.

yLCD display for easy navigation and addressing.

yPerfect for disco, club, bar, parties and Mobile DJs.

Voltage: 100V~240V, 50/60Hz

Power consumption: 130W

Light source: 1×50W White LED

Dimension: 299X247X437 mm

ΦRotating gobo =22 mm

ΦFixed gobo =24 mm

Weight: 10.2 kg

287

437

236

103361

259 299

247

216

Photometric diagram:

3. How To Set The Unit

3.1 Control panel

Display

To show the various menus and the selected functions

LED

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

Button

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

Only for remote control

Connecting with CA-8/CA-9/CA-9RTX to control the unit for Stand by, Function and Mode function.

Mains input

Connect to power supply.

DMX input/output

For DMX512 link, use 3/5-pin XLR cable to link the unit together.

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is showing on the

display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press the ENTER button to setup, to go

back to the functions without any change press the MENU button again. Hold and press the MENU button

about one second or wait for one minute to exit the menu mode.

The main functions are showing below:

DMX Address

Select DMX Address, press ENTER button to confirm, the present address will blink on the display. Use

UP and DOWN button to adjust the address from 1to 512. Once the address has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button again. Hold

and press the MENU button about one second or wait for one minute to exit the menu mode.

Channel Mode

Select Channel Mode, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the 15 Chan (15 Channel Mode) or 16 Chan (16 Channel Mode) mode. Once the

mode has been selected, press the ENTER button to setup, to go back to the functions without any change

press the MENU button again. Hold and press the MENU button about one second or wait for one minute to

exit the menu mode.

Show Mode

Select Show Mode, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the Show 1 or Show 2 or Show 3 or Show 4 mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Split Color Mode

Select Split Color Mode, press ENTER button to confirm, present mode will blink on the display. Use

DOWN and UP button to select the Yes (Split Color mode) or No (normal) mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Slave Mode

Select Slave Mode, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the Slave 1 (normal) or Slave 2 (2 light show) mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Black Out

Select Slave Mode, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the Yes (yes blackout) or No (no blackout) mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Sound State

Select Sound State, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the On (sound on) or Off (sound off) mode. Once the mode has been selected,

press the ENTER button to setup, to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu mode.

Sound Sense

Select Sound Sense, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the 0…100 mode. Once the mode has been selected, press the ENTER button to

setup, to go back to the functions without any change press the MENU button again. Hold and press the

MENU button about one second or wait for one minute to exit the menu mode.

Pan Inverse

Select Pan Inverse, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the Yes (pan inversion) or No (normal) mode. Once the mode has been selected,

press the ENTER button to setup, to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu mode.

Tilt Inverse

Select Pan Inverse, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the Yes (tilt inversion) or No(normal) mode. Once the mode has been selected,

press the ENTER button to setup, to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu mode.

Back Light

Select Back Light, press ENTER button to confirm, present mode will blink on the display. Use DOWN and

UP button to select the On (Led on) or Off (Led off) mode. Once the mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button again. Hold

and press the MENU button about one second or wait for one minute to exit the menu mode.

Gobo1 Focus

Select Gobo1 Focus, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the 0…255 mode. Once the mode has been selected, press the ENTER button to

setup, to go back to the functions without any change press the MENU button again. Hold and press the

MENU button about one second or wait for one minute to exit the menu mode.

Gobo2 Focus

Select Gobo2 Focus, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the 0…255 mode. Once the mode has been selected, press the ENTER button to

setup, to go back to the functions without any change press the MENU button again. Hold and press the

MENU button about one second or wait for one minute to exit the menu mode.

Function Delay

Select Function Delay, press ENTER button to confirm, present mode will blink on the display. Use DOWN

and UP button to select the No Delay or 1S/2S/3S Delay (Wait for 1/2/3 seconds before these Functions of

15/16 CH are activated/deactivated) mode. Once the mode has been selected, press the ENTER button to

setup, to go back to the functions without any change press the MENU button again. Hold and press the

MENU button about one second or wait for one minute to exit the menu mode.

Dimmer Calibrate

Press the MENU button to show Dimmer Calibrate on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP button to calibrate the dimmer for a maximum output from 50

(limited to 50% of the really max. output) to 100 (maximum output is not limited). Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Auto-Test

Press the MENU button up to when the Auto-Test is blinking on the display. Pressing ENTER button and

the unit will run self-test by built-in program. To go back to the functions press the MENU button again. Hold

and press the MENU button about one second or wait for one minute to exit the menu mode.

Temperature

Press the MENU button up to when the Temperature Test is blinking on the display. Pressing ENTER

button and the display will show the temperature of the unit. To go back to the functions press the MENU

button again. Hold and press the MENU button about one second or wait for one minute to exit the menu

mode.

When the temperature of the fixture is up to 50°, the display will show

When the temperature of the fixture is higher than 60°, the LED will be off and the display will show

Fixture Time

Press the MENU button up to when the Fixture Time is blinking on the display. Pressing ENTER button

and the display will show the number of working hours of the unit. To go back to the functions press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Firmware Version

Press the MENU button up to when the Firmware version is blinking on the display. Pressing ENTER

button and the display will show the version of software of the unit. To go back to the functions press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Defaults Setting

Press the MENU button to show Defaults on the display. Press the ENTER button and the display will blink.

Use the DOWN and UP button to select the Confirm? YES or Confirm? No.Once the Confirm? Yes has

been selected, press the ENTER button and use the UP and Down button to select the PRO Def or AUTO

Def.

PRO Defaults: For professional users, detailed explanation as followings:

)Channel Mode Æ16 Chan

)Split Color Mode ÆYes

)Slave Mode ÆSlave 1

)Black Out ÆYes

)Sound State ÆOff

)Sound Sense Æ90

HIGH LED

50°

LED OFF

OVER TEMP

)Pan Inverse ÆNo

)Tilt Inverse ÆNo

)Back Light ÆOff

)Function Delay Æ3S Delay

AUTO Defaults: Mostly automatic mode, for non professional users, detailed explanation as

followings:

)Channel Mode Æ15 Chan

)Split Color Mode ÆNo

)Slave Mode ÆSlave 1

)Black Out ÆNo

)Sound State ÆOn

)Sound Sense Æ90

)Pan Inverse ÆNo

)Tilt Inverse ÆNo

)Back Light ÆOn

)Function Delay Æ3S Delay

(Notice: Other settings are NOT changed while choosing Defaults Setting!)

Press the ENTER and the corresponding functions will set to defaults setting, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about one second or

wait for one minute to exit the menu mode.

Reset

Press the MENU button up to when the Reset is blinking on the display. Pressing ENTER button and all

channels of the unit will return to their standard position.

3.3 Home Position Adjust

In the main functions, hold Enter button for at least 3 seconds into offset mode, use DOWN and UP button

up to chose Pan Offset, Tilt Offset ,Color Offset, Gobo1 Offset, R-Gobo Offset, Gobo2 Offset, Prism

Offset, R-Prism Offset or Focus Offset, pressing ENTER Pressing ENTER button and the display will

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME E-40D TC DXX Bedienungsanleitung

ACME

ACME RAYZOR HYBRID XA-100 BSW Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME LED-PAR 100 WW/CW Bedienungsanleitung

ACME

ACME LED-BL4B Bedienungsanleitung

ACME

ACME O2 Oxygen Bedienungsanleitung

ACME

ACME Dotline360 TB-1230 QW Bedienungsanleitung

ACME

ACME LP-TS200 CW Bedienungsanleitung

ACME

ACME TB-1010QW II Bedienungsanleitung

ACME

ACME E-10T WW DXX Bedienungsanleitung

ACME

ACME LED-MS50A Bedienungsanleitung

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME AE-610 BEAM Bedienungsanleitung

ACME

ACME Stage Blinder P4 Bedienungsanleitung

ACME

ACME E-10C WW DXX Bedienungsanleitung

ACME

ACME ORION XP-260 BEAM Bedienungsanleitung

ACME

ACME LED-635S Bedienungsanleitung

ACME

ACME GLORY PROFILE Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME BLINDER LINE 10 IP Bedienungsanleitung

ACME

ACME UV-9N Bedienungsanleitung

ACME

ACME GENESIS COLOR II Bedienungsanleitung

ACME

ACME LED-RC8 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung

ACME iMove 50SR Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken