ACME Dotline360 TB-1230 QW Bedienungsanleitung

TB-1230 QW

User Manual

Please read the instrucon carefully before use

CONTENTS

1. Safety Instructions ............................................................................................. 2

2. Technical Specifications .....................................................................................3

3. How To Set The Unit...........................................................................................4

3.1 Control panel.......................................................................................................................... 4

3.2 Main Functions.......................................................................................................................6

3.3 HomePosition Adjustment................................................................................................... 13

4.DMX Controller ................................................................................................. 14

4.1 DMX 512 Configurations ...................................................................................................... 15

5. How to Control the Unit...................................................................................18

5.1 DMX 512 Connections ................................................................................... 18

6. Troubleshooting ............................................................................................... 19

7. Fixture Cleaning ............................................................................................... 19

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they

also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces.

Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when installing this unit. DO NOT handle the unit by taking its head only, but always by

taking its base.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature is

higher than this.

Unit surface temperature may reach up to 70 degrees C. DO NOT touch the housing with bare-hands

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

The housing and lenses must be replaced if they are visibly damaged.

Installation:

The fixture should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating and make sure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the fixtures weight. Always use

a safety cable that can hold 12 times of the weight of the fixture when installing. The equipment must be

installed by professionals and it must be installed in a place where is out of the reach of people and no

one can pass by or under it.

2. Technical Specifications

2 DMX Channel Modes: 57 / 14 Channels

Power Supply: AC 100~240V, 50/60Hz

Power Consumption: 450W

Power Supply: 12 ×30W RGBW LED

Power Cable Daisy Chain: 4 Fixtures Max.(120V, 60Hz); 7 Fixtures Max. (230V, 50Hz)

Beam Angle: 3.5°-38°

Weight: 17.5Kgs

Dimension: 1000 × 113 × 278mm

Fixture Rotation Angle Range:0°-215°

3. How To Set The Unit

3.1 Control panel

LCOK UNLCOK

1. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

2. Function Display:

Show the various menus and the selected functions;

3.Battery Display:

To show battery status.

4.DMX IN:

Water proof 5-pin XLR connectors for DMX 512 operation;

5. DMX OUT:

Water proof connectors for DMX 512 operation, 5-pin XLR cable to output DMX signal;

6. POWER IN:

To connect to the mains supply;

7. POWER OUT:

connect to the next unit;

8. ETHERNET:

Transfers fixture’s information to a main controller.

9.FUSE(T10A):

Protect the unit from damage of the overcurrent

10.PUSH BUTTON 1 (Head Push Button):

Before the fixture is powered on , please push the button to “UNLOCK” of the head;

11.PUSH BOTTON 2:

When the fixture is online , please push the button to “LOCK”;

3.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display. Select the

function by the ENTER button and the display will blink. Use the DOWN/UP button to change the mode.

Once the required mode has been selected, press the ENTER button to setup or it will automatically

return to the main functions without any change after idling one minute. Back to the functions without

any change press the MENU button.

The main functions are shown below:

DMX Setting

To select DMX Settings press the ENTER button to confirm, use the UP/DOWN button to select ArtNet

Setup, DMXAddress, Channel Mode or RDM Device ID.

ArtNet Setup

To select ArtNet Setup, press the ENTER button to confirm. Use the UP/DOWN button to select

Ethernet IP Setup or ArtNet Port Setup channels mode, press the ENTER button to store. When

choose Ethernet IP Setup, use the UP/DOWN button to select IP Address or Subnet Mask.When

choose Art-Net Port Setup, use the UP/DOWN button to select Net, Subnet or Universe. Press the

MENU button back to the last menu or let the unit idle one minute to exit menu mode.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust

the address from 001 to 512, press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle one minute to exit menu mode.

Channel Mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

57 CH or 14 CH channels mode, press the ENTER button to store. Press the MENU button back to

the last menu or let the unit idle one minute to exit menu mode.

RDM Device ID

To select RDM Device ID, press the ENTER button to show RDM Device ID on the display, and press

the ENTER button again, it will show the RDM Device ID. To go back to the functions without any

changes press the MENU button.

DMX Last State

To select DMX Last State , press the ENTER button to show DMX Last State on the display. Use the

DOWN/UP buttons to select Black Out, Hold or Manu, Once the mode has been selected, press the ENTER

button to setup. To go back to the functions without any changes press the MENU button again. Press

and hold the MENU button for about one second or wait for 7 seconds to exit the menu mode.

Fixture Setting

To select Fixture Setting, press the ENTER button to show Fixture Setting on the display. Use the

DOWN/UP buttons to select Light Mode, Dimmer Curve, Dimmer Speed, Invert Tilt, Tilt Feedback, Bl.O.

Tilt Moving or Fan Mode. Once the mode has been selected, press the ENTER button to setup. To go

back to the functions without any changes press the MENU button again. Press and hold the MENU

button for about one second or wait for 7 seconds to exit the current mode.

Light Mode

To select Light Mode, press the ENTER button to confirm. Use the UP/DOWN button to select Color

Calibration or Max, press the ENTER button to store. When choose Color Calibration, use the

UP/DOWN button to select Disable or Enable.When choose Max, press the ENTER button to enter

White Balance ，use the UP/DOWN button to select Red, Green or Blue. Press the MENU button back

to the last menu or let the unit idle one minute to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display. Use

theDOWN/UP button to select the Optically Linear or Square Law or Inverse Square Law or S-Curve.

Once the mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Press and hold the MENU button about one

second or wait for one minute to exit the menu mode.

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME SPLENDOR 90 Bedienungsanleitung

ACME

ACME LP-F2000 VW Bedienungsanleitung

ACME

ACME Ellipsoidal 10 DMX Bedienungsanleitung

ACME

ACME Dotline 360 Bedienungsanleitung

ACME

ACME CEILING 40 Bedienungsanleitung

ACME

ACME MP-400Z IP Bedienungsanleitung

ACME

ACME LED-RC8 Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME IU-01 Bedienungsanleitung

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME LED-ST1000 Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME ARAS Bedienungsanleitung

ACME

ACME LED-245 II Bedienungsanleitung

ACME

ACME Stage Blinder P4 Bedienungsanleitung

ACME

ACME GENESIS COLOR II Bedienungsanleitung

ACME

ACME SAMBA Color Bedienungsanleitung

ACME

ACME Dragonfly Quad Bedienungsanleitung

ACME

ACME CW-108 Bedienungsanleitung

ACME

ACME MH-575S Bedienungsanleitung

ACME

ACME LED-BL8 Bedienungsanleitung

ACME

ACME TB-1010QW II Bedienungsanleitung

ACME

ACME O2 Oxygen Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung