ACME MP-90 RGBW Bedienungsanleitung

MP-90 RGBW

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Introductions .................................................................................................. 2

2.Technical Specifications .............................................................................................. 4

3.How To Set The Fixture............................................................................................... 4

3.1 Control Panel ................................................................................................. 4

3.2 Main Function................................................................................................... 5

4. How To Control The Unit ......................................................................................... 10

4.1 Master/Slave Built In Preprogrammed Function ............................................ 10

4.2 DMX Controller ............................................................................................... 10

5. DMX512 Configuration ............................................................................................ 12

6. DMX512 Connections.............................................................................................. 13

7. Troubleshooting....................................................................................................... 14

8. Fixture Cleaning....................................................................................................... 14

1. Safety Introductions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

All fixtures are intact from the manufacturer, please operate follow up the user manual,

artificial fault are not under guarantee repair.

Unpack and check carefully that there is no transportation damage before using the unit.

The unit is for indoor use only. Use only in a dry location.

Do install and operate by operator.

Use safety chain when fixes the unit. Don’t handle the unit by taking its head only, but always

by taking its base.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Maximum ambient temperature TA : 40℃. Don’t operate it where the temperature is higher

than this.

Don’t connect the device to any dimmer pack.

First run, there will be smoke or smells, and all disappearing a few minutes later.

Make sure there are no flammable materials close to the unit while operating, as it is fire

hazard.

Look over power wires carefully, replace immediately if there is any damage.

Never run on for a long time lest shortening lifespan.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happen, cut

off the mains power immediately.

Do not operate in dirty and dusty environment, also cleaning fixtures regularly.

Do not allow children to operate the fixture.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Do not touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together around other cables.

Disconnect mains power before fuse/lamp replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Do not open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center.

Disconnect the mains power if the fixture is not used for a long time.

Do use original packing materials once transport it again.

Do not look directly at the LED light beam while the fixture is on.

Possibly hazardous optical radiation emitted from this product.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2.Technical Specifications

Voltage

：

100-240V~ 50/6 0 Hz

LED: 3W CREE XP-E LED x 90pcs,

Red:18PCS; Green:24PCS; Blue:24PCS; White:24PCS.

Fuse: T 6.3A

Power consumption

：

280W

Dimension

：

234 x 299 x 265 mm

Weight

：

7.9kg/pcs

3.How To Set The Fixture

3.1 Control Panel

○

1 Display: To show the various menus and the selected functions

○

2 LED:

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

○

3 Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

○

4 Microphone: Receive music for the sound active.

○

5 DMX output: For DMX512 link, use 3/5 -pin XLR plug cable to link the next unit.

○

6 DMX input: For DMX512 link, use 3/5 -pin XLR plug cable to input DMX signal

○

7 Mains input: Connect to supply mains power for the next unit.

3.2 Main Function

To select any functions, press MENU button until the required one is shown on the display. Select

the function by ENTER button and the display will blink. Use DOWN and UP button to change the

mode. Once the required mode has been selected, press ENTER button to setup or it will

automatically return to the main functions without any change after idling one minute. Back to the

functions without any change press MENU button. The main functions are shown below:

DMX 512 Address Setting

Press the MENU button up to when is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the address

has been selected, press ENTER button to setup or automatically exit menu mode without any

change after one minute. Back to the previous functions without any change press MENU button.

Channel Mode

Press the MENU button up to when is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to select the (4 channels mode) or

(5 channels mode) or (7 channels mode). Once the mode has been selected,

press the ENTER button to setup or automatically exit menu mode without any change after one

minute. To go back to the functions without any change press the MENU button.

Slave Mode

Press the MENU button up to when is showing on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to select the (Master) (Slave 1) or

(Slave 2) mode. Once the mode has been selected, press the ENTER button to setup or

automatically return to the main functions without any change after one minute. To go back to the

functions without any change press the MENU button again.

Show Mode

Press the MENU button up to when is shown on the display. Pressing ENTER button, Use

DOWN and UP button to select the (Random show) or (color) or

(fade), if you select the color or fade mode, press ENTER button to confirm, and use DOWN and UP

button to select color 1-10 or fade speed (speed 1: slow, speed 2: middle, speed 3: fast). Once

select, press ENTER button to setup or automatically exit menu mode without any change after one

minute. To go back to the last function without any change press the MENU button.

Dimmer Mode

Press the MENU button up to when is shown on the display. Pressing ENTER button, Use

DOWN and UP button to select the (Dimmer Mode 1: Optically Linear),

(Dimmer Mode2 : Square Law), (Dimmer Mode 3: Inverse Square Law) or

(Dimmer Mode 4: S-cure), press ENTER button to confirm. Once select, press ENTER button to

setup or automatically exit menu mode without any change after one minute. To go back to the last

function without any change press the MENU button.

Optically Linear Square Law Inverse Square Law S-curve

Optically Linear: The increase in light intensity appears to be linear as DMX value is increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels. Inverse Square

Law: Light intensity control is coarser at low levels and finger at high levels.

S-cure: Light intensity control is finger at low levels and high levels and coarser at medium levels.

Sound Mode

Press the MENU button up to when is shown on the display. Pressing ENTER button, Use

DOWN and UP button to select the (sound on) or (sound off).Once select,

press ENTER button to setup or automatically exit menu mode without any change after one

minute. To go back to the functions without any change press the MENU button

Sound Sense

Press the MENU button up to when is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to adjust sensitivity of the sound control from 0 to

100. Once selected, press ENTER button to setup or automatically exit menu mode without any

change after one minute. Back to the previous functions without any change press MENU button.

Blackout mode

Press the MENU button up to when is shown on the display. Pressing ENTER button, Use

DOWN and UP button to select the (blackout) or (normal).Once select, press

ENTER button to setup or automatically exit menu mode without any change after one minute. To

go back to the functions without any change press the MENU button

LED

Press the MENU button up to when is shown on the display. Pressing ENTER button and

the display will blink. Use DOWN and UP button to select (display always on) or

(display off 20 seconds after exit menu) mode. Once select, press ENTER button to setup or

exit menu mode without any change after one minute. Back to the functions without any change

press MENU button again.

Display Inverse

Press MENU button until is blinking on the display. Use DOWN and UP button to select

(display normal) or (display inverse), press ENTER button to setup. Back to the

functions without any change press MENU button.

White Balance

Press the MENU button up to when is shown on the display. Pressing ENTER button, and

use DOWN and UP button to select , or , press ENTER button to confirm

and use DOWN and UP button to adjust the value between 125 and 255, once select press ENTER

button to setup or automatically exit menu mode without any change after one minute. To go back

to the last function without any change press the MENU button.

Manual setting color

Press the MENU button up to when is shown on the display. Pressing ENTER button, and

use DOWN and UP button to select , or … or (strobe), press ENTER

button to confirm and use DOWN and UP button to adjust the value, once select press ENTER

button to setup or automatically exit menu mode without any change after one minute. To go back

to the last function without any change press the MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER

button and the unit will run the built-in programmer for self-test. To go back to the functions

press the MENU button.

Temperature Test

Press the MENU button up to when is blinking on the display. Pressing ENTER button and

the display will show the temperature of the unit. To go back to the functions press the MENU

button again.

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME FURY LED RGB Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME IM-5S-ELC Bedienungsanleitung

ACME

ACME XP-1000WZ Bedienungsanleitung

ACME

ACME Eventx 100 Bedienungsanleitung

ACME

ACME Theatre LED Colour Flood Bedienungsanleitung

ACME

ACME Ellipsoidal E-300 D2550 Bedienungsanleitung

ACME

ACME TB-1010QW II Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME AE-610 BEAM Bedienungsanleitung

ACME

ACME CP-56U Bedienungsanleitung

ACME

ACME MH-640S-ELC Bedienungsanleitung

ACME

ACME ELLIPSOIDAL E-300 Bedienungsanleitung

ACME

ACME ARAS Bedienungsanleitung

ACME

ACME ORION XP-260 BEAM Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME LED-MS50A Bedienungsanleitung

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME LED-245 II Bedienungsanleitung

ACME

ACME MH-600A Mobile Color Bedienungsanleitung

ACME

ACME LED-256D RGB Bedienungsanleitung

ACME

ACME MH-575S Bedienungsanleitung

ACME

ACME WHACK XP-231 BEAM Bedienungsanleitung

ACME

ACME E-10C WW DXX Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung