ACME TB-1010QW II Bedienungsanleitung

TB-1010QW II

User Manual

Please read the instruction carefully before use

CONTENTS

1. Safety Instructions ..................................................................................................2

2. Technical Specifications ..........................................................................................3

3. How To Set The Unit ...............................................................................................4

3.1 Control panel .................................................................................................... 4

3.2 Main Functions ................................................................................................. 5

4. How to Control the Unit ....................................................................................... 10

4.1 DMX 512 Connections .................................................................................... 10

4.2 DMX Controller............................................................................................... 11

4.3 DMX 512 Configurations.................................................................................12

5. Troubleshooting.................................................................................................... 15

6. Fixture Cleaning.................................................................................................... 16

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they

also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces.

Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when installing this unit. DO NOT handle the unit by taking its head only, but always by

taking its base.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature is

higher than this.

Unit surface temperature may reach up to 70 degrees C. DO NOT touch the housing with bare-hands

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

The housing and lenses must be replaced if they are visibly damaged.

Installation:

The fixture should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating and make sure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the fixtures weight. Always use

a safety cable that can hold 12 times of the weight of the fixture when installing. The equipment must be

installed by professionals and it must be installed in a place where is out of the reach of people and no

one can pass by or under it.

2. Technical Specifications

Power Supply: AC 100~240V, 50/60Hz

Power Consumption: 130W

Power Cable Daisy Chains: 18 Fixtures Max. (230V, 50Hz)

10 Fixtures Max. (120V, 60Hz)

Light Source: 10×15W RGBW LEDs

Beam Angle: 10°

Weight: 10Kgs

Dimension: 953 × 104 × 112mm

112 mm

104 mm

Distance(m)

2468

9227 4374 1025 57710 Lux°

Diameter(m)

1 0°

Photometrics Diagram

0 32.0 63.0.96

1 28.

3. How To Set The Unit

3.1 Control panel

1. DMX IN:

Water proof 3-pin XLR connectors for DMX 512 operation;

2. POWER IN:

Water proof connectors for power input;

3. Function Display:

Show the various menus and the selected functions;

4. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

5. POWER OUT:

Water proof connectors for power output;

6. DMX OUT:

Water proof connectors for DMX 512 operation, 3-pin XLR cable to output DMX signal;

3.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display. Select the

function by the ENTER button and the display will blink. Use the DOWN/UP button to change the mode.

Once the required mode has been selected, press the ENTER button to setup or it will automatically

return to the main functions without any change after idling one minute. Back to the functions without

any change press the MENU button.

The main functions are shown below:

Once you set to , after running in show mode for 5 minutes

without any change or restarting the unit, the key board become locked. Press the

ENTER button to enable the menu, the display will show , press the

UP/DOWN button until it shows , then press the ENTER to unlock.

DMXADDRESS

CHANNEL MODE

SHOW MODE

BLACKOUT MODE

MANUAL TEST

WHITE BALANCE

PASSWORD

LOCK

DISPLAY INVERSION

NORMAL

AUTO TEST

LED DISPLAY

FIXTURE TEMPERATURE

FIXTURE USE HOURS

FIRMWARE VERSION

DIMMER SPEED

DMX 512 ADDRESS

To select , press the ENTER button to show DMX ADDRESS on the display. Use the DOWN/UP

buttons to adjust the address from 1 to 512. Once the address has been selected, press the ENTER button

to setup. To go back to the functions without any changes press the MENU button again. Press and hold

the MENU button for about one second or wait for 7 seconds to exit the menu mode.

CHANNEL MODE

To select , press the ENTER button to show CHANNEL MODE on the display. Use the DOWN/UP

button to select 4, 4D, 4C or 40 channel modes. Once the mode has been selected, press the ENTER

button to setup. To go back to the functions without any changes press the MENU button again. Press

and hold the MENU button for about one second or wait for 7 seconds to exit the menu mode.

SHOW MODE

To select , press the ENTER button to show SHOW MODE on the display. Use the DOWN/UP

buttons to select (show 1) or … (show 16), and then press the ENTER button to confirm,

the (fade time) will blink on the display, use the DOWN/UP button to adjust the fade time (0 ~

255); and press the ENTER button again, the will blink to display, use the DOWN/UP button to

adjust the wait time (0 ~ 255). Press and hold the MENU button for about one second or wait for 7

seconds to exit the menu mode.

BLACKOUT MODE

To select , press the ENTER button to show BLACKOUT MODE on the display. Use the DOWN/UP

buttons to select (blackout) or (normal) mode. Once the mode has been selected, press

the ENTER button to setup. To go back to the functions without any changes press the MENU button

again. Press and hold the MENU button for about one second or wait for 7 seconds to exit the current

mode.

MANUAL TEST

To select , press the ENTER button to show MANUAL TEST on the display. Use the DOWN/UP

button to select (red), (green), (blue), (white), (dimmer) or

(strobe) on the display. Once the mode has been selected, press the ENTER button to confirm. Use the

DOWN/UP buttons to specify a value for the chosen effect from 0to 255. To go back to the functions

without any changes press the MENU button again. Press and hold the MENU button for about one

second or wait for 7 seconds to exit the menu mode.

WHITE BALANCE

To select , press the ENTER button to show WHITE BALANCE on the display. Use the DOWN/UP

button to select (red), (green) or (blue). Once selected, press the ENTER button to

confirm .Use the DOWN /UP buttons to change its value (125 to 255). Once the address has been

selected, press the ENTER button to setup. To go back to the functions without any changes press the

MENU button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the menu mode.

PASSWORD

To select , press the ENTER button to show PASSWORD on the display. Use the DOWN/UP buttons

to change the password (000 to 9999). Once the address has been selected, press the ENTER button to

setup. To go back to the functions without any changes press the MENU button again. Press and hold the

MENU button for about one second or wait for 7 seconds to exit the menu mode.

LOCK

To select , press the ENTER button to show LOCK on the display. Use the DOWN/UP buttons to

select (blackout) or (normal) mode. Once the mode has been selected, press the

ENTER button to setup. To go back to the functions without any changes press the MENU button again.

Press and hold the MENU button for about one second or wait for 7 seconds to exit the current mode.

DISPLAY INVERSE

To select , press the ENTER button to show DISPLAY INVERSE on the display, and press the ENTER

button again, it will show the (inversion). To go back to the functions without any changes press

the MENU button.

AUTO TEST

To select , press the ENTER button to show AUTO TEST on the display and the unit will run a

self-test . To go back to the functions without any changes press the MENU button again. Press and hold

the MENU button for about one second or wait for 7 seconds to exit the current mode.

LED DISPLAY

To select , press the ENTER button to show LED DISPLAY on the display. Use the DOWN/UP button

to select (LED on) or (LED off) mode. Once the mode has been selected, press the

ENTER buttons to setup. To go back to the functions without any changes press the MENU button again.

Press and hold the MENU button for about one second or wait for 7 seconds to exit the current mode.

FIXTURE TEMPERATURE

To select , press the ENTER button to show the FIXTURE TEMPERATURE on the display and the

display will show the temperature of the unit. To go back to the functions without any changes press the

MENU button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the menu mode.

FIXTURE USE HOURS

To select , press the ENTER button to show FIXTURE USE HOURS on the display and the display

will show the number of working hours of the unit . To go back to the functions without any changes

press the MENU button again. Press and hold the MENU button for about one second or wait for 7

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME SPLENDOR 90 Bedienungsanleitung

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME E-200 MB MC Bedienungsanleitung

ACME

ACME LED-BL8 Bedienungsanleitung

ACME

ACME Festival LED-787 Bedienungsanleitung

ACME

ACME ELLIPSOIDAL E-300 Bedienungsanleitung

ACME

ACME LED-BL4B Bedienungsanleitung

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME Solaris CM-S6 Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME LED-635S Bedienungsanleitung

ACME

ACME LED-MS150 Bedienungsanleitung

ACME

ACME FURY LED RGB Bedienungsanleitung

ACME

ACME DVS-2500 Bedienungsanleitung

ACME

ACME ENERGY HYBRID Bedienungsanleitung

ACME

ACME LED-245 II Bedienungsanleitung

ACME

ACME Elf Laser Bedienungsanleitung

ACME

ACME MP-400Z IP Bedienungsanleitung

ACME

ACME Dragonfly Quad Bedienungsanleitung

ACME

ACME LED-7871 Bedienungsanleitung

ACME

ACME PAGEANT 300ZR II Bedienungsanleitung

ACME

ACME CP-21TC Bedienungsanleitung

ACME

ACME Stage Blinder P4 Bedienungsanleitung

ACME

ACME XP-470 BSW Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung