ACME MH-600A Mobile Color Bedienungsanleitung

User Guide

Professional Entertainment Technology

Широкий ассортимент оборудования ACME

на www.maxlight.ru

EC Declaration of Conformity

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL:2000+A12:2002

Safety of household and similar electrical appliances

Part 1 : General requirements

INDEX

A. GENERAL INSTRUCTIONS

B. MAIN FEATURES

C. LAMP

D. HOW TO CONTROL THE UNIT

1. By universal DMX controller

2. Preprogrammed function

3. By easy controller

E. FIXTURE CLEANING

A. GENERAL INSTRUCTIONS

Please read the enclosed instructions carefully as they include important points

about safety for the installation, usage and maintenance of the unit.

• Please keep this booklet with the unit for future consultation. If you sell the unit to

another user, be sure that the new user also receives this instruction booklet thus

giving them the necessary information about the use and general warnings

regarding the unit.

• Before the initial start-up, please unpack and carefully check all components in

case any damage may have occurred during shipping.

• Locate a suitable spot for your device where there is good ventilation. Also, make

sure that no ventilating fans or slots are blocked.

• Protect our environment! Please dispose of the packing boxes properly.

• The electrical work that is necessary for installation must be done by qualified

personnel.

• Always remember to unplug the unit from the power mains before any service is

done. Do not open the unit, there are no serviceable parts inside.

• It is very important to ground the yellow/green conductor to earth in order to meet

regulations for safety.

• Check the surrounding area and make sure there are no flammable liquids, water

or metal objects that could enter the fixture. If a foreign object enters the unit,

immediately disconnect the main power. Also, place the fixture in a

well-ventilated room at about 15 cm from the walls.

• Do not touch any wires during operation, as high voltage might be hazardous.

• I n the event of serious operating problems, stop using the unit immediately. Never

try to repair the unit yourself. Repairs carried out by unqualified personnel can

lead to damage or malfunction. Please contact the nearest authorized Technical

Assistance Center. Always use genuine spare parts.

E. FIXTURE CLEANING

The cleaning of internal and external optical lenses and/or mirrors must be

carried out periodically to optimize light output. Cleaning frequency depends on the

environment in which the fixture operates: damp, smoky or particularly dirty

surrounding can cause greater accumulation of dirt on the unit’s optics.

• Clean with a soft cloth using normal glass cleaning products.

• Always dry the parts carefully.

• Clean the external optics at least once every 20 days. Clean the internal optics

at least every 30/60 days.

For further requirements, contact the nearest authorized technical assistance center.

( 2 ) Preprogram functions

• The unit can be linked together as master/slave in 4 or 8 channels and run by

built in preprogrammed chase sequences automatically or by sound activation.

Please refer to dip switch setting table for how to set the dip switches to achieve

master/slave linking.

• The first unit dip switch 10 must be on in master/slave mode

( 3 ) By easy controller

The easy remote control is used only in master/slave mode. By connecting

to the 1/4” microphone jack of the first unit, you will find that the remote control

on the first unit will control all the other units for Stand by, Strobe/Next and

Fast/Slow function.

1. STAND BY : blackout and switch off the bulb.

2. STROBE/NEXT : when the unit is in fast mode press the

button and keep pressed up, it will strobe by sound activation.

If the unit is in slow mode, you can select the next color and

next sequences.

3. FAST/SLOW : when the led light off, it is in FAST mode. The

unit change color by sound activation. If the led light on, it is

in SLOW mode, you can select the next color by NEXT

button.

B. MAIN FEATURES

• Voltage：AC 110~120V 60Hz or AC 230/240/250V 50/60Hz

• Bulb：JCR 15V 150W

• The unit is a DMX512 compatible color changer. It features full DMX512 control,

10 dichroic colors plus clear and shutter, accurate focus able optics system and

stepper motor with blackout and switch off the bulb feature. Fan cooled.

• T hermal switch for overheat protection.

• It can be operated by DMX512 control or can be used as an individual unit

without a control.

• It can be linked together in master/slave combination units, as many as required

in 4 or 8 channels and run by built-in preprogrammed chase sequences

automatically or by sound activation through an internal microphone to create an

intelligent effect.

• Please use a 3 pin XLR cable/plug when connecting them together.

• It features different preprogrammed chase patterns.

• Dimensions：265 x 140 x 160 mm

• Weight：5.0 kg

C. LAMP

JCR 15V 150W

• Always switch off the mains supply and never handle the lamp or luminaire when

it is hot.

• Do not touch the bulb with bare hands. If this does happen, clean the lamp with

denatured alcohol and wipe with a lint free cloth before installing.

Unit Dip switches setting

Master

Slave 1

Slave 2

Slave 3

DMX512

Termination reduces signal errors and to avoid signal

(Resistance 120 ohm 1/4W) between pin2 (DMX-) and

transmission problems and interference. It is always

pin3 (DMX+) of the last fixture.

advisable to connect a DMX terminal.

DMX -

COMMON

DMX +

120 ohm 1/4W

1 2 3 4

D. HOW TO CONTROL THE UNIT

( 1 ) By universal DMX controller

The DMX512 is widely used in intelligent lighting control, with a maximum of

512 channels.

• A DMX512 system requires a controller, lighting equipment and cable. These

are connected together in a “daisy chain” with the terminator at the end. The

cable cannot be branched or split to a “Y” cable.

• The terminator requires a 90-120 Ohm 1/4 Watt resistor soldered between two

signal cables.

• The DMX512 uses a very high speed signal. Inadequate or damaged cables,

bad solder joints or corroded connectors can easily distort the signal and shut

down the system. A reliable DMX512 system starts with good quality cables.

• Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to

1).

• The end of the DMX512 system should be terminated to reduce signal errors.

• 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5

pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

DMX512 CONFIGURATION

• Start the address

How to address your DMX512 system:

1. Select the channels of DMX controller

2. Dip switches

Dip #1 #2 #3 #4 #5 #6 #7 #8 #9 #10

Value 1 2 4 8 16 32 64 128 256 M/S

• Examples:

Channel 1 : dip / on : #1 ( 1 )

Channel 2 : dip / on : #2 ( 2 )

Channel 3 : dip / on : #1, #2 ( 1+2 = 3 )

Channel 4 : dip / on : #3 ( 4 )

DMX512 Leave Range 0 ~ 255

255 Fastest speed strobe

224 Slowest speed strobe

192-223 Rainbow effect slow to fast

176-191 Pink

160-175 Magenta

144-159 Light Blue

128-143 Light Green

112-127 Orange

96-111 Amber

80-95 Green

64-79 Blue

48-63 Yellow

32-47 Red

16-31 White

00-15 Blackout

Channel Dip switches setting

Ch 01

Ch 02

Ch 03

Ch 04

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME Festival LED-787 Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME LED-MTX36 HEX Bedienungsanleitung

ACME

ACME ARAS Bedienungsanleitung

ACME

ACME FURY LED RGB Bedienungsanleitung

ACME

ACME LP-F2000 VW Bedienungsanleitung

ACME

ACME XP-1000WZ Bedienungsanleitung

ACME

ACME MACE Bedienungsanleitung

ACME

ACME LS-608 RGB Bedienungsanleitung

ACME

ACME iMove 50SR Bedienungsanleitung

ACME

ACME CW-108 Bedienungsanleitung

ACME

ACME CP-21TC Bedienungsanleitung

ACME

ACME CYC-200 FC Bedienungsanleitung

ACME

ACME SAMBA Color Bedienungsanleitung

ACME

ACME XP-1200F Bedienungsanleitung

ACME

ACME CP-56U Bedienungsanleitung

ACME

ACME E-10 WW DXX Bedienungsanleitung

ACME

ACME CB-16FC Bedienungsanleitung

ACME

ACME XA-500 Bedienungsanleitung

ACME

ACME MP-90 RGBW Bedienungsanleitung

ACME

ACME Junior Series Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME LED-MB50 Bedienungsanleitung

ACME

ACME LED?7TC Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung