ACME Stage Blinder P4 Bedienungsanleitung

Stage Blinder P4

LED-BL4/LED-BL4 CW

User Guide

Please read these instructions carefully before use

Contents

1. Safety Instructions .........................................................................2

2. Technical Specifications .................................................................3

3. Installation.....................................................................................4

4. How to set the unit.........................................................................5

4.1 Rear Panel.................................................................................5

4.2 Main Function ...........................................................................6

5. How To Control The Unit................................................................9

6. DMX Channel Mode......................................................................11

7. DMX512 Connections...................................................................12

8. Troubleshooting ..........................................................................12

9. Fixture Cleaning...........................................................................13

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the

fixture to another user, be sure that they also receive this instruction booklet.

Please unpack and check carefully there is no transportation damage before

using the fixture.

Please disconnect main power before servicing and maintenance.

The unit must be installed in a location with adequate ventilation, at least 50cm

from adjacent surfaces. Be sure that no ventilation slots are blocked.

The maximum ambient temperature is Ta: 40℃. DO NOT operate it where the

temperature is higher than this.

DO NOT connect the device to any dimmer pack.

The housing must be replaced if they are visibly damaged.

Unit surface temperature may reach up to 85℃. Don’t touch the housing

bare-hand during its operation. Turn off the power and allow about 15 minutes

for the unit to cool down before replacing or serving.

There are no user serviceable parts inside the fixture. Do not open the housing

or attempt any repairs by yourself. In the unlikely event your fixture may require

service, please contact your nearest dealer.

Please read the instructions carefully which includes important

In the event of serious operating problem, stop using the fixture immediately.

Never try to repair the fixture by yourself. Repairs carried out by unskilled

people can lead to damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the same type spare parts.

It’s important to ground the yellow/green conductor to earth in order

to avoid electric shock.

DO NOT touch any wire during operation and there might be a hazard of electric

shock.

DO NOT expose the fixture to rain or moisture, in order too prevent

or reduce the risk of electrical shock or fire.

Do not look directly at the LED light beam while the fixture is on.

2. Technical Specifications

DMX 1/2/4/5 channels switchable.

Smooth 0~100% dimming and variable strobe speeds.

Two operation modes: DMX, Manual mode.

For AC 230V 50Hz power supply, the maximum fixtures that can be connected on one power cable is

12;

Ideal for discotheques, clubs, bars, parties, Mobile DJs, etc.

Input Voltage: AC 100V~240V 50/60Hz

Total Power consumption: 380W

Fuse: T6.3A

LED: 4 x 65W LED

Color temperature: 2700K 100K (LED-BL4) 5700K 200K(LED-BL4 CW)

Dimension: 500x 400 x 182 mm

Weight: 9.5Kgs

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure

that the unit is firmly fixed to avoid vibration and slipping while operating. Always

ensure that the structure to which you are attaching the unit is secure and is able to

support a weight of 10 times of the unit’s weight. Also always use a safety cable

that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place

where is out of the touch of people and has no one pass by or under it.

4. How to set the unit

4.1 Rear Panel

○

1 Display: Show the various menus and the selected functions

○

2 LED:

DMX On DMX input present

○

3 Button:

MENU To select the programming functions

DOWN

To go backward in the selected

functions

To go forward in the selected

functions

ENTER To confirm the selected functions

○

4 Mains input/output:

Connect to supply mains power, and Connect to supply mains power for the next

unit.

○

5Fuse holder: 6.3A

○

6DMX input/output:

For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal, and to link the

next unit.

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the

display. Select the function by ENTER button. Use DOWN and UP button to change

the mode. Once the required mode has been selected, press ENTER button to setup

or it will automatically return to the main functions without any change after idling

8 seconds. Back to the functions without any change press MENU button. The main

functions are shown below:

DMX 512 Address

Select the , press the ENTER button and the display will blink. Use the DOWN

and UP button to change the DMX 512 address. Once the address has been selected,

press the ENTER button to setup or automatically exit menu mode without any

change after 8 seconds. Back to the previous functions without any change press

the MENU button.

Channel Mode

Select the , press the ENTER button. Use the DOWN and UP button to select

the channel mode (1 /2/4/5). Once selected, press the ENTER button to setup or

automatically exit menu mode without any change after 8 seconds. To go back to

the functions without any change press the MENU button

Manual Mode

Select the , press the ENTER button. Use the DOWN and UP button to select

ON /OFF , after selected, press the ENTER button. If you select the ON,

press the ENTER button, use the DOWN and UP button to select 000-100, and press

the ENTER button to setup or automatically exit menu mode without any change

after 8 seconds. To go back to the functions without any change press the MENU

button

Tungsten Filament Effect

Select the , press the ENTER button. Use the DOWN and UP button to select

(the effect will display when the light turn off or move) or (the effect

won’t display when the light turn off or move). Once selected, press the ENTER

button to setup or exit menu mode without any change after 8 seconds. Back to the

functions without any change press the MENU button again.

LED display

Select the , press the ENTER button. Use the DOWN and UP button to select

(LED display on) or (LED display off). Once selected, press the ENTER

button to setup or exit menu mode without any change after 8 seconds. Back to the

functions without any change press the MENU button again.

Temperature Display

Select the , press ENTER button and the display will show the temperature of

each unit ，，， . To go back to the functions press the

MENU button.

Firmware version

Select the , press ENTER button and the display will show the version of

software of the unit. To go back to the functions press the MENU button.

5. How To Control The Unit

You can operate the unit in two ways:

1. By manual controller

2. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX

address setting will be affected at once. Turn on the unit, if there is DMX or without

DMX and manual mode turn off, the LED will display the saved channel address

（001-512）; If there isn’t DMX and manual mode turn on, the LED will display

saved manual address.（D000-D100）。

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME E-10T WW DXX Bedienungsanleitung

ACME

ACME LED-BR10 Bedienungsanleitung

ACME

ACME FURY LED RGB Bedienungsanleitung

ACME

ACME LED-Exercet Bedienungsanleitung

ACME

ACME MINI ELLIPSOIDAL 10 Bedienungsanleitung

ACME

ACME iMove 50SR Bedienungsanleitung

ACME

ACME LED-MB50 Bedienungsanleitung

ACME

ACME DVS-2500 Bedienungsanleitung

ACME

ACME XP-1200F Bedienungsanleitung

ACME

ACME Ellipsoidal E-300 D2550 Bedienungsanleitung

ACME

ACME Stage Panel 1080 Bedienungsanleitung

ACME

ACME ORION XP-260 BEAM Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME LED-635S Bedienungsanleitung

ACME

ACME Color Spot Bedienungsanleitung

ACME

ACME LED-7871 Bedienungsanleitung

ACME

ACME LS-608 RGB Bedienungsanleitung

ACME

ACME CEILING 40 Bedienungsanleitung

ACME

ACME LED-PAR 100 WW/CW Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME Color Fusion CF-805 Bedienungsanleitung

ACME

ACME Dragonfly Quad Bedienungsanleitung

ACME

ACME Dotline360 TB-1230 QW Bedienungsanleitung

ACME

ACME E-10 WW DXX Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung