ACME CM-150 PAGEANT 150 Bedienungsanleitung

PAGEANT 150

CM-150

UserGuide

Professional Entertainment Technology

CONTENTS

1. Safety Instruction......................................................................................................2

2. Technical Specification .............................................................................................3

3. How To Set The Unit.................................................................................................4

3.1 Control panel..........................................................................................................4

3.2 Main Function.........................................................................................................4

3.3 Home Position Adjustment ...................................................................................10

4. How To Control The Unit.........................................................................................11

4.1 Master/Slave Built In Preprogrammed Function...................................................11

4.2 Easy Controller.....................................................................................................11

4.3 DMX Controller.....................................................................................................12

4.4 DMX 512 Configuration........................................................................................13

4.5 DMX512 Connection ............................................................................................19

5. Troubleshooting......................................................................................................20

6. Fixture Cleaning .....................................................................................................21

1. Safety Instruction

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces.

Be sure that no ventilation slots are blocked.

yDisconnect main power before replacement or servicing.

yMake sure there are no flammable materials close to the unit while operating as it is fire hazard.

yUse safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by

taking its base.

yMaximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than

this.

yUnit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or

serving.

yIn the event of serious operating problem, stop using the unit immediately. Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

yDO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

yDO NOT open the unit within five minutes after switching off.

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Please read carefully this instruction, which includes important information

about the installation, usage and maintenance.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs

yourself. In the unlikely event your unit may require service, please contact your nearest dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you are

attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight.Also always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by the professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2. Technical Specification

◇Extremely small, fast and powerful LED moving beam and wash effect.

◇DMX Channels: 1/9/12/14/16/28 channel mode

◇Beam angle: 10°

◇Smooth electronic dimming: 0-100%

◇Electronic strobe with pulse and random effects

◇Optional easy controller CA-8 or CA-9 RTX for instant lighting shows at your fingertips

◇High efficiency, low power consumption

◇Super compact, low weight

Power Supply: AC 100V~240V, 50/60Hz

Fuse: T 6.3A

Power consumption: 105W

Lightsource: 7 x 10W LED

Weight: 5.7Kgs

Dimension: 258X167X304mm

3. How To Set The Unit

3.1 Control panel

Display:

To show the various menus and the selected functions

LED: DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

Only for remote control:

Connecting with CA-8/ CA-9RTX to control the unit for Stand by, Function and Mode function.

Mains input:

Connect to power supply.

Mains output:

Connect to supply power to the next unit.

DMX input/output:

For DMX512 link, use 3/5-pin XLR cable to link the unit together.

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is showing on

the display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press the ENTER button to setup, to go

back to the functions without any change press the MENU button again. Hold and press the MENU

button about one second or wait for one minute to exit the menu mode.

The main functions are showing below:

DMX Address

Select DMX Address, press the ENTER button to confirm, the present address will blink on the display.

Use the UP and DOWN button to adjust the address from 1to 512. Once the address has been selected,

press the ENTER button to setup, to go back to the functions without any change press the MENU

button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Channel Mode

Select Channel Mode, press the ENTER button to confirm, present mode will blink on the display. Use

the DOWN and UP button to select the 1 chan, 9 chan or 12 chan，14 chan or 16 chan or 28 chan

mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions

without any change press the MENU button again. Hold and press the MENU button about one second

or wait for one minute to exit the menu mode.

Show Mode

Select Show Mode, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the Show 1 or Show 2 or Show 3 or Show 4 mode. Once the mode has

been selected, press the ENTER button to setup, to go back to the functions without any change press

the MENU button again. Hold and press the MENU button about one second or wait for one minute to

exit the menu mode.

Dimmer curve

Select Dimmer curve, press the ENTER button to confirm, present mode will blink on the display. Use

the DOWN and UP button to select the Mode1 or Mode 2 or Mode 3 or Mode 4 mode. Once the mode

has been selected, press the ENTER button to setup, to go back to the functions without any change

press the MENU button again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

Mode 1(Optically Linear): The increase in light intensity appears to be linear as DMX value is

increased.

Mode 2(Square Law): Light intensity control is finer at low levels and coarser at high levels.

Mode 3(Inverse Square Law): Light intensity control is coarser at low levels and finger at high levels.

Mode 4(S-cure): Light intensity control is finger at low levels and high levels and coarser at medium

levels.

Slave Mode

Select Slave Mode, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the Slave 1 (normal) or Slave 2 (2 light show) mode. Once the mode

has been selected, press the ENTER button to setup, to go back to the functions without any change

press the MENU button again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

Black Out

Select Slave Mode, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the Yes (yes blackout) or No (no blackout) mode. Once the mode has

been selected, press the ENTER button to setup, to go back to the functions without any change press

the MENU button again. Hold and press the MENU button about one second or wait for one minute to

exit the menu mode.

Sound State

Select Sound State, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the On (sound on) or Off (sound off) mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit

the menu mode.

Sound Sense

Select Sound Sense, press the ENTER button to confirm, present mode will blink on the display. Use

the DOWN and UP button to change the sound sense from 0…100. Once the mode has been selected,

press the ENTER button to setup, to go back to the functions without any change press the MENU

button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Pan Inverse

Select Pan Inverse, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the Yes (pan inversion) or No (normal) mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit

the menu mode.

Tilt Inverse

Select Pan Inverse, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the Yes (tilt inversion) or No(normal) mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit

the menu mode.

Back Light

Select Back Light, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the On (Led on) or Off (Led off) mode. Once the mode has been

selected, press the ENTER button to setup, to go back to the functions without any change press the

MENU button again. Hold and press the MENU button about one second or wait for one minute to exit

the menu mode.

Function Delay

Select Function Delay, press ENTER button to confirm, present mode will blink on the display. Use

DOWN and UP button to select the No Delay or 1S/2S/3S Delay (Wait for 1/2/3 seconds before these

Functions of 9/16/28CH are activated/deactivated) mode. Once the mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button again.

Hold and press the MENU button about one second or wait for one minute to exit the menu mode.

White Balance

Select White Balance, press the ENTER button to confirm, present mode will blink on the display. Use

the DOWN and UP button to select the Red or Green or Blue. Once the mode has been selected, press

the ENTER button to setup, use the DOWN and UP button to change the value (125~255). Once the

mode has been selected, press the ENTER button to setup, go back to the functions without any change

press the MENU button again. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

Manu Test

Select Manu Test, press the ENTER button to confirm, present mode will blink on the display. Use the

DOWN and UP button to select the Pan/ Tilt/ Red1/ Green1/ Blue1/ White1/…Red4/ Green4/ Blue4/

White4/ Dimmer or Strobe. Once the mode has been selected, press the ENTER button to setup, use

the DOWN and UP button to change the value (0~255). Once the mode has been selected, press the

ENTER button to setup, go back to the functions without any change press the MENU button again.

Hold and press the MENU button about one second or wait for one minute to exit the menu mode.

Auto-Test

Press the MENU button up to when the Auto-Test is blinking on the display. Pressing ENTER button

and the unit will run self-test by built-in program. To go back to the functions press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu

mode.

Temperature

Press the MENU button up to when the Temperature Test is blinking on the display. Pressing ENTER

button and the display will show the temperature of the unit. To go back to the functions press the MENU

button again. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME CP-18TC Bedienungsanleitung

ACME

ACME Building wash Bedienungsanleitung

ACME

ACME STAGE PAR 400 ZOOM IP Bedienungsanleitung

ACME

ACME Neozone Bedienungsanleitung

ACME

ACME LED-275 D Bedienungsanleitung

ACME

ACME DOT Bedienungsanleitung

ACME

ACME SAMURAI SCAN 50 Bedienungsanleitung

ACME

ACME CHIRON Bedienungsanleitung

ACME

ACME BOOTES Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME Sandane Bedienungsanleitung

ACME

ACME LED-SC25 Bedienungsanleitung

ACME

ACME SABER Mini Bedienungsanleitung

ACME

ACME V-BOX Bedienungsanleitung

ACME

ACME Theatre Spot 150m Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME Libre Bedienungsanleitung

ACME

ACME TOUR PIXEL BAR 1010 II Bedienungsanleitung

ACME

ACME PIXEL LINE IP Bedienungsanleitung

ACME

ACME DELUGE LED-WAV-50W Bedienungsanleitung

ACME

ACME Diamonds II Bedienungsanleitung

ACME

ACME Warrior Scan 50 LED-SC50C Bedienungsanleitung

ACME

ACME BP-183 RGBW S R DXX Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung