ACME BP-183 RGBW S R DXX Bedienungsanleitung

BP-183 RGBW S AR DXX

TABLE OF CONTENTS

1. Safety Instructions.................................................................................................. 2

2. Technical Specifications .......................................................................................... 3

3. How To Set The Fixture........................................................................................... 4

3.1 Control Panel .................................................................................................... 4

3.2 Main Functions................................................................................................. 5

4. How To Control The Fixture.................................................................................. 10

4.1 DMX Controller............................................................................................... 10

4.2 DMX 512 Configuration .................................................................................. 10

5. DMX512 Connections........................................................................................... 12

6. Troubleshooting ................................................................................................... 13

7. Cleaning And Maintenance .................................................................................. 13

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when installing this unit. DO NOT handle the unit by taking its head only, but

always by taking its base.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature is

higher than this.

Unit surface temperature may reach up to 75 degrees C. DO NOT touch the housing with

bare-hands during its operation. Turn off the power and allow about 15 minutes for the unit to

cool down before replacing or serving.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating and make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the fixtures weight.

Always use a safety cable that can hold 12 times of the weight of the fixture when installing.

The equipment must be installed by professionals and it must be installed in a place where is out

of the reach of people and no one can pass by or under it.

2. Technical Specifications

IP66 rated LED Spotlight with rich, saturated color mixing effect via specially designed lens

provides outstanding light output;

Compact design with great heat ventilation in a rugged die-cast aluminum housing to ensure

reliable performance under harsh environments;

With Photocell (light sensor) feature, units can light up automatically when the environment is

getting dark;

LED touch-panel display for easy set-up navigation; It also comes with great built-in shows

(fade) without DMX control

Perfect for illumination of building façade, hotels, landscapes, theme park and more.

Input Voltage: AC 100-240V, 50/60Hz

Power Consumption: 48W

LED: 18 x 3W LEDs (R:4, G:5, B:5, W:4)

Beam Angle: 6°, 15°, 25°, 40°, 60°, 80°

Weight: 3.8Kgs

Dimension: 315 x 178 x 162mm

3. How To Set The Fixture

3.1 Control Panel

1. Function Display:

Used To show the various menus and the selected functions

2. Button:

To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER

To confirm the selected functions

3. DMX IN:

Water proof cable with 3-pin XLR connectors for DMX 512 operation

4. POWER IN:

Water proof power cable with connectors for power input

5. POWER OUT:

Water proof cable with connectors for power output

6. DMX OUT:

Water proof cable with connectors for DMX 512 operation with 3-pin XLR plug

3.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display.

Select the function by the ENTER button and the display will blink. Use the DOWN/UP button to

change the mode. Once the required mode has been selected, press the ENTER button to setup or

it will automatically return to the main functions without any change after idling one minute. Back

to the functions without any change press the MENU button.

The main functions are shown below:

DMX 512 Address

Select the , press the ENTER button and the display will blink. Use the DOWN/UP button

to change the DMX 512 address between 1 and 512. Once the address has been selected, press the

ENTER button to save or automatically exit menu mode without any change after one minute. Back

to the previous functions without any change press the MENU button.

Channel mode

Select the , press the ENTER button and the display will blink. Use the DOWN/UP button

to select the (4 Channels: Red, Green, Blue, White), (5 Channels: Red, Green,

Blue, White, Dimmer) or (7 Channels: Red, Green, Blue, White, Color, Dimmer, Strobe)

Mode. Once select the required mode, press the ENTER button to save or automatically exit menu

mode without any change after one minute. To go back to the functions without any change press

the MENU button.

Show mode

Select the , press the ENTER button and the display will blink. Use the DOWN/UP button

to select the (show 1)…. (show 16). Once select, press the ENTER button to

setup. press the ENTER button，will blinking on the display, use the DOWN/UP button

adjust the fade time (0~255), press the ENTER button to store and will blinking on the

display, use the DOWN/UP button adjust the white time (0~255), press the ENTER button to store

or automatically return to the main functions without any change after one minute. To go back to

the previous functions without any change press the MENU button.

Blackout mode

Select the , press the ENTER button and the display will blink. Use the DOWN/UP button

to select the (blackout) or (normal). Once selected, press the ENTERbutton

to setup or automatically exit menu mode without any change after one minute. To go back to the

functions without any change press the MENU button.

Manual Mode

Press the MENU button up to when the is shown on the display. Press the ENTER button

and the display will blink. Use the DOWN/UP button to select the (Red),

(Green), (Blue), (White), (Dimmer) or (Strobe).

Once selected, press the ENTER button to setup, then use the DOWN/UP button to adjust the

value (0~255) or automatically exit menu mode without any change after one minute. To go back

to the functions without any change press the MENU button.

White Balance

Press the MENU button up to when the is showing on the display. Pressing the ENTER

button and the display will blink. Use the DOWN/UP button to select the (Red)，

(Green), or (Blue) mode. Once selected, press the ENTER button to setup,

then use the DOWN/UP button to adjust the value (125~255) or automatically exit menu mode

without any change after one minute. To go back to the functions without any change press the

MENU button.

Photo Cell

Select the , press the ENTER button and the display will blink. Use the DOWN/UP button

to select the (Be controlled by sunlight) or (Not be controlled by sunlight)，

Once select, press the ENTER button to setup or automatically return to the main functions

without any change after one minute. Back to the previous functions press the MENU button.

Photo Cell Intensity

Select the , press the ENTER button and the display will blink. Use the DOWN/UP button

to adjust the intensity vale between and . Once selected, press the ENTER

button to setup or automatically return to the main functions without any change after one

minute. Back to the previous functions press the MENU button.

Time Setup

Select the , press the ENTER button and the display will blink. Use the DOWN/UP button

to adjust the (1 hour) … (10 hours) mode. Once select, press the ENTER

button to setup or automatically return to the main functions without any change after one

minute. Back to the previous functions press the MENU button.

Display Inversion

Press the MENU button up to when the is showing on the display. Pressing the ENTER

button and the display will blink. Use the DOWN/UP button to select the (normal) or

(inverse), Once the mode has been selected, press the ENTER button to setup or

automatically return to the main functions without any change after one minute. To go back to the

previous functions without any change press the MENU button.

Auto Test

Select the , press the ENTER button and the unit will run self-test by built-in program. To go

back to the functions press the MENU button again.

LED Display

Press the MENU button up to when the is shown on the display. Press the ENTER button

and the display will blink. Use the DOWN/UP button to select (display on) or

(display off 20 seconds after exit menu) mode. Once select, press the ENTER button to setup or

exit menu mode without any change after one minute. Back to the functions without any change

press the MENU button again.

Temperature Test

Press the MENU button up to when the is blinking on the display. Press the ENTER

button and the display will show the temperature of the unit. To go back to the functions press the

MENU button again.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Press the ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the MENU button.

Software version

Press the MENU button up to when the is blinking on the display. Press the ENTER

button and the display will show the version of software of the unit. To go back to the functions

press the MENU button again.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Solar Flare Bedienungsanleitung

ACME

ACME V Inground VI-10QW Bedienungsanleitung

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME BIG BANG Bedienungsanleitung

ACME

ACME ENERGY HYBRID X-400 BSW Bedienungsanleitung

ACME

ACME LED-SC252 Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME IM-250 SP Bedienungsanleitung

ACME

ACME iSolution Bedienungsanleitung

ACME

ACME FLASHDOT Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME Inferno Bedienungsanleitung

ACME

ACME Stage Par 220MP-220 Bedienungsanleitung

ACME

ACME Splendor 220 II Bedienungsanleitung

ACME

ACME LED-256D-10W Bedienungsanleitung

ACME

ACME Dotline180 Bedienungsanleitung

ACME

ACME IP Cabin AR-01 Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME LED STROBE 50 Bedienungsanleitung

ACME

ACME LED-275 D Bedienungsanleitung

ACME

ACME LED-MTX6S-8W Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung