ACME TOUR PIXEL BAR 1010 II Bedienungsanleitung

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. How To Set The Unit....................................................................................... 5

3.1 Control Panel ........................................................................................... 5

3.2 Main Functions ........................................................................................ 6

4. Control By Universal DMX Controller ........................................................... 12

4.1 DMX512 Connections ............................................................................ 12

4.2 Address Setting ...................................................................................... 13

4.3 DMX512 Configurations ......................................................................... 13

5. Troubleshooting........................................................................................... 17

6. Fixture Cleaning ........................................................................................... 17

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is suitable for indoor use and wet locations. Do not immerse in water.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 70℃. DO NOT touch the housing bare-handed

during its operation.

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the LED is on.

DO NOT start on the unit without LED enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of the

reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

130W

Light Source:

10x15W RGBW LED

Beam Angle:

10°

Dimmer/Shutter:

0~100% smooth dimming, adjustable electronic strobe effect

Control:

DMX Channel: 4/5/7/4 0 Channels

Control Mode: DMX512

Firmware Upgrade: Update via DMX link

Construction:

Display: LED display

Data In/Out: 3-pin waterproof connector

Power In/Out: Power cord out

Protection Rating: IP65

Features:

Efficient LED lens, uniform color mixing, which makes the light effect better

LEDs can be controlled pixel by pixel

Equal distance design, horizontal stitching can achieve dynamic water effects, vertical stitching can

achieve matrix effect

IP65 design is suitable for fixed installation or mobile performance

Moreover, the fixture can be adjusted to 180° backward and forward by double mounting brackets

Adding the atomized paper, the full angle can reach 60 °, it can expand the effective wash range

(optional)

Extra installation of the barn door can prevent glare and stray light effectively (optional)

Dimensions/Weight:

953x104x112mm, 10.6kgs

37.5"x4.1"x4.4"in, 23.4lbs

112 mm

104 mm

Photometrics Diagram:

3. How To Set The Unit

3.1 Control Panel

1. DMX IN:

Water proof connectors for DMX512 operation, use 3-pin XLR cable to input DMX signal

2. POWER IN: Water proof connectors for power input

3. Function Display: To show the various menus and the selected functions

4. Button:

MENU To select the programming functions

DOWN To go forward in the selected functions

UP To go backward in the selected functions

ENTER To confirm the selected functions

5. POWER OUT: Water proof connectors for power output

6. DMX OUT:

Water proof connectors for DMX512 operation, use 3-pin XLR cable to output DMX signal

3.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display.

Select the function by the ENTER button and the display will blink. Use the DOWN/UP button to

change the mode. Once the required mode has been selected, press the ENTER button to setup or it

will automatically return to the main functions without any change after idling 7 seconds. Back to

the functions without any change press the MENU button.

The main functions are shown below:

Once you set to , after running in show mode for 5 minutes

without any change or restarting the unit, the key board become locked. Press the

ENTER button to enable the menu, the display will show , press the

UP/DOWN button until it shows , then press the ENTER to unlock.

DMXADDRESS

CHANNEL MODE

SHOW MODE

BLACKOUT MODE

MANUAL TEST

WHITE BALANCE

PASSWORD

LOCK

DISPLAY INVERSION

NORMAL

AUTO TEST

LED DISPLAY

FIXTURE TEMPERATURE

FIXTURE USE HOURS

FIRMWARE VERSION

DIMMER SPEED

DMX ADDRESS

To select , press the ENTER button to show DMX ADDRESS on the display. Use the DOWN/UP

buttons to adjust the address from 1 to 512. Once the address has been selected, press the ENTER

button to setup. To go back to the functions without any changes press the MENU button again.

Press and hold the MENU button for about one second or wait for 7 seconds to exit the menu

mode.

CHANNEL MODE

To select , press the ENTER button to show CHANNEL MODE on the display. Use the

DOWN/UP button to select 4, 4D, 4C or 40 channel modes. Once the mode has been selected, press

the ENTER button to setup. To go back to the functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the menu mode.

SHOW MODE

To select , press the ENTER button to show SHOW MODE on the display. Use the DOWN/UP

buttons to select (show 1) or … (show 16), and then press the ENTER button to

confirm, the (fade time) will blink on the display, use the DOWN/UP button to adjust the

fade time (0-255); and press the ENTER button again, the will blink to display, use the

DOWN/UP button to adjust the wait time (0-255). Press and hold the MENU button for about one

second or wait for 7 seconds to exit the menu mode.

DIMMER SPEED

To select , press the ENTER button to show DIMMER SPEED on the display. Use the

DOWN/UP button to select (smooth) or (fast). Once the mode has been selected,

press the ENTER button to setup. To go back to the functions without any changes press the MENU

button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit

the menu mode.

BLACKOUT MODE

To select , press the ENTER button to show BLACKOUT MODE on the display. Use the

DOWN/UP buttons to select (blackout) or (normal) mode. Once the mode has

been selected, press the ENTER button to setup. To go back to the functions without any changes

press the MENU button again. Press and hold the MENU button for about one second or wait for 7

seconds to exit the current mode.

MANUAL TEST

To select , press the ENTER button to show MANUAL TEST on the display. Use the DOWN/UP

button to select (red), (green), (blue), (white), (dimmer) or

(strobe) on the display. Once the mode has been selected, press the ENTER button to

confirm. Use the DOWN/UP buttons to specify a value for the chosen effect from 0to 255. To go

back to the functions without any changes press the MENU button again. Press and hold the MENU

button for about one second or wait for 7 seconds to exit the menu mode.

WHITE BALANCE

To select , press the ENTER button to show WHITE BALANCE on the display. Use the

DOWN/UP button to select (red), (green) or (blue). Once selected, press the

ENTER button to confirm .Use the DOWN /UP buttons to change its value (125 to 255). Once the

address has been selected, press the ENTER button to setup. To go back to the functions without

any changes press the MENU button again. Press and hold the MENU button for about one second

or wait for 7 seconds to exit the menu mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME HYGIEA Bedienungsanleitung

ACME

ACME LED-0408 Bedienungsanleitung

ACME

ACME LED Move 600SE Bedienungsanleitung

ACME

ACME LP-F1000 CW Bedienungsanleitung

ACME

ACME BIG BANG Bedienungsanleitung

ACME

ACME LED-WAV-10W Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME STORM Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME LP-1600 BD30 Bedienungsanleitung

ACME

ACME CHIRON Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

ACME

ACME Pageant CM-200Z Bedienungsanleitung

ACME

ACME LS-1005 Bedienungsanleitung

ACME

ACME VOGUE Bedienungsanleitung

ACME

ACME RAYZOR HYBRID Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME FLANDINA 22 IP Bedienungsanleitung

ACME

ACME Dynamic 25 Roller LED-SC25B Bedienungsanleitung

ACME

ACME SAMURAI SCAN 50 Bedienungsanleitung

ACME

ACME ANIMA C Bedienungsanleitung

ACME

ACME LED-MS600 PE Bedienungsanleitung

ACME

ACME Xperior XP-380 BEAM IP F Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung