ACME Theatre Spot 150m Bedienungsanleitung

CONTENTS

1. Safety Instructions..................................................................................2

2. Technical Specifications ..........................................................................4

3. The Plate for Color Filter & Barn Door Installation .................................5

4. How To Set The Unit ...............................................................................6

4.1 Control panel ....................................................................................6

4.2 Main Functions .................................................................................7

5. Control By Universal DMX Controller....................................................12

5.1 Connection .....................................................................................12

5.2 Address Setting...............................................................................13

5.3 DMX512 Configuration ...................................................................13

6. Troubleshooting....................................................................................14

7. Fixture Cleaning....................................................................................15

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The

dealer will not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

The unit is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head

only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Maximum ambient temperature TA: 40℃，maximum ambient temperature TA: 0℃.

DO NOT connect the device to any dimmer pack.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Please read the instruction carefully which includes important information

about the installation, usage and maintenance.

Unit’s surface temperature may reach up to 85℃. DO NOT touch the housing bare-handed

during its operation, and allow about 15 minutes for cooling the unit down before replacing

bulb or maintenance as it could be very hot.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than

12 meters.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

DO NOT look directly at the light while the LED is on.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

320W

Light Source:

TS-300M CW: C117C1916-300-006

TS-300M WW: C117W1916-300-006

Color Temperature:

3200±200K, 5500±200K(optional)

Optical:

CRI: WW≥95，CW≥95

CQS: WW≥94，CW≥93

TLC: WW≥95，CW≥95

Control:

DMX Channel: 1/2 Channels Mode

Control Mode: DMX, Master/Slave, Manual, Art-Net

Firmware Upgrade: Update via DMX link

Construction:

Display: LCD display

Data In/Out: 5-pin XLR

Power In/Out: Power Connector in/out

Protection Rating: IP20

Features:

Manual focus, zoom range: 15°~53°

Manual linear dimming

4 dimming curves, 2 optional dimming speed

0~100% smooth dimming

Low noise under 35dB within 1m

Rotating barn door and hanger

Dimensions/Weight:

531x340x284mm, 10.5kgs

21"x13"x11"in, 23.2lbs

531 340

284

Photometric Diagram:

3. The Plate for Color Filter & Barn Door Installation

Fig. 1

At first, please push the Lock Cap button by hand as the arrow ①, and move away the Lock as the

arrow ②; Then insert the Plate for Color Filter into the inside slot from topside ③;

Fig. 2

Secondly, please insert the Barn Door into the outside slot from topside as arrow ④, and fasten

the lock (Note: the Barn Door must be fastened into the inside of the lock’s hook ); then flip down

the lock cap again as arrow⑤.

4. How To Set The Unit

4.1 Control panel

1. Display: Shows the various menus and the selected functions

2. LED:

MASTER On Master Mode

SLAVE On Slave Mode

DMX On DMX input present

3. Button:

MENU To select the programming functions

DOWN To go forward in the selected functions

UP To go backward in the selected functions

ENTER To confirm the selected functions

4. Dimmer:

Manual adjust the dimmer value

5. Zoom:

Manual adjust the zoom value

6. DMX IN:

For DMX512 link, use 5-pin XLR cable to link the units together

7. POWER IN:

Connects to supply power

8. POWER OUT:

Connects to the next unit

9. DMX OUT:

For DMX512 link, use 5-pin XLR cable to link the unit together

10. Fuse (T 10A):

Used to protect the unit from damage of the over-current

11. ETHERNET:

Connect with the multimedia and use software to control the units via ArtNet

4.2 Main Functions

To select any functions, press the MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use the DOWN and UP button to

change the mode. Once the required mode has been selected, press the ENTER button to setup or

it will automatically return to the main functions without any change after idling one minute. Back

to the functions without any change press the MENU button.

The main functions are shown below:

DMX Address

Select DMX Address, press the ENTER button to confirm, the present address will blink on the

display. Use the UP/DOWN button to adjust the DMX address from 1to 512. Once the address has

been selected, press the ENTER button to save. Hold and press the MENU button about one

second or wait for one minute to exit the menu mode.

Art-Net Setup

Select Art-Net Setup, press the ENTER button to confirm. Use the UP/DOWN button to select

Ethernet IP Setup or Art-Net Port Setup. Once selected, press the ENTER button to save. Hold and

press the MENU button about one second or wait for one minute to exit the menu mode.

Channel Mode

Select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select the

1 CH or 2 CH. Once selected, press the ENTER button to save. Hold and press the MENU button

about one second or wait for one minute to exit the menu mode.

Dimmer Speed

Select Dimmer Speed, press the ENTER button to confirm. Use the UP/DOWN button to select

Smooth(dimmer speed smooth) or Fast(dimmer speed fast). Once selected, press the ENTER

button to save. Hold and press the MENU button about one second or wait for one minute to exit

the menu mode.

Dimmer Curve

Select Dimmer Curve, press the ENTER button to confirm. Use the UP/DOWN button to select

Linear Curve, Sq.Law Curve, Invert Sq. Law Curve or S Curve. Once selected, press the ENTER

button to store. Press the MENU button back to the last menu or let the unit idle one minute to

exit menu mode.

Andere Handbücher für Theatre Spot 150m

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME COMET Bedienungsanleitung

ACME

ACME LED Move 600SE Bedienungsanleitung

ACME

ACME VOGUE Bedienungsanleitung

ACME

ACME DMX512 Dynamic Scan Bedienungsanleitung

ACME

ACME Pageant CM-200Z Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME DAZZLED COLORLED-430 Bedienungsanleitung

ACME

ACME DOT Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

ACME

ACME Oxygen Bedienungsanleitung

ACME

ACME LED-HC101 II Bedienungsanleitung

ACME

ACME Energy Spot PRO Bedienungsanleitung

ACME

ACME DIABOLO 500 Bedienungsanleitung

ACME

ACME LED-3082 RGB Bedienungsanleitung

ACME

ACME TRACK 10 Bedienungsanleitung

ACME

ACME BW-54-10FC II RL Bedienungsanleitung

ACME

ACME LS-1005 Bedienungsanleitung

ACME

ACME CP-18TC Bedienungsanleitung

ACME

ACME Building wash Bedienungsanleitung

ACME

ACME ENERGY HYBRID X-400 BSW Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME Inferno Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung