ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

User Manual

Please read the instruc on carefully before use

XA-400 SPOT

CONTENTS

1. Safety Instructions..........................................................................................2

2. Technical Specifications..................................................................................3

3. How To Set The Unit.......................................................................................5

3.1 Control panel............................................................................................5

3.2 Main Function ..........................................................................................6

3.3 Home Position Adjustment.....................................................................11

4. Control By Universal DMX Controller ...........................................................14

4.1 DMX Connection ....................................................................................14

4.2 Address Setting.......................................................................................15

4.3 DMX 512 Configuration..........................................................................15

5. Troubleshooting ...........................................................................................22

6. Fixture Cleaning ...........................................................................................23

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 75℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Please read carefully the instruction, which includes important information

about the installation, usage and maintenance.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

400W

Light Source:

300W LED

Color Temperature:

8000K

Zoom Angle:

7°~31°

Movement:

Pan: 540°

Tilt: 260°

Pan/Tilt Resolution: 16 bit

Color Wheel:

2 color wheels, both of them have 7 colors plus open

Gobo Wheel:

1 static gobo wheel with 10 gobos plus open

1 rotating gobo wheel with 7 gobos plus open, easy to replace

Prism:

8 facet prism, rotating in both directions

Construction:

Display: LCD display

Data In/Out: 5-pin XLR

Power In/Out: Wire; PowerCon in

Protection Rating: IP20

Control:

DMX Channel: 19/22 channels

Control Mode: DMX512, RDM

Firmware Upgrade: Update via DMX link

Features:

Motorized linear zoom system with wash effect

1 linear iris

Various strobe speeds

Dimensions/Weight:

430x254x674mm, 22.7kgs

16.9"x10"x26.5"in, 50lbs

Photometric Diagram:

3. How To Set The Unit

3.1 Control panel

Wire Version:

1234 5 67

POWERCON Version:

1. LED:

POWER On Power On

DMX On DMX input present

2. Display: Used to show the various menus and the selected function

3. Button:

MENU To select the programming functions

DOWN To go forward in the selected functions

UP To go backward in the selected functions

ENTER To confirm the selected functions

4. DMX IN/OUT: DMX 512 link, use XLR cable to link the unit and DMX controller to input/output

the DMX signal

5. POWER WITCH: Turn on/off the power

6. FUSE (T 6.3A): Protect the unit from damage of the overcurrent

7. POWER(Wire Version):To connect to supply power

8. POWER IN/POWER OUT(POWERCON Version):To connect to supply power/ To connect to the

next fixture

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by the ENTER button and the display will blink. Use the

DOWN and UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu

mode.

The main functions are showing below:

DMX Settings

To select DMX Settings, press the ENTER button to confirm, use the UP/DOWN button to select

DMX Address, DMX Channel Mode, DMX State or View DMX Value.

DMX Address —DMX512 address setting

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to

adjust the address from 001 to 512, press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

DMX Channel Mode

To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button

to select Mode 1(19) or Mode 2(22), press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode

DMX State —fixture state while DMX single stops

To select DMX State, press the ENTER button to confirm. Use the UP/DOWN button to select

Blackout (fixture blacks out if DMX signal stops) or Hold (fixture continues to obey the last

command it received Via DMX if DMX signal stops), press the ENTER button to store. Press the

MENU button back to the last menu or let the unit idle one minute to exit menu mode

View DMX Value

To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to

view the DMX channel value. Press the MENU button back to the last menu or let the unit idle

one minute to exit menu mode.

Fixture Settings

To select Fixture Settings, press the ENTER button to confirm, use the UP/DOWN button to select

Pan Inverse, Tile Inverse, P/T Feedback, BL.O. P/T Moving, BL.O. Color Change,BL.O. Gobo

Change.

Pan Inverse

To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select

No (normal) or Yes (pan inverse), press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

Tilt Inverse

To select Tilt Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select

No (normal) or Yes (tilt inverse), press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle one minute to exit menu mode.

P/T Feedback

To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to

select No (Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while

pan/tilt out of step), press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle one minute to exit menu mode.

BL.O. P/T Moving —Blackout while pan/tilt moving

To select BL.O. P/T Moving, press the ENTER button to confirm. Use the UP/DOWN button to

select No (normal while pan/tilt moving) or Yes (blackout while pan/tilt moving), press the

ENTER button to store. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

BL.O. Color Change — Blackout while change color

To select BL.O. Color Change, press the ENTER button to confirm. Use UP/DOWN button to

select No (normal while changing color) or Yes (blackout while change color), press the ENTER

button to store. Press the MENU button back to the last menu or let the unit idle one minute

to exit menu mode.

BL.O. Gobo Change — Blackout while change gobo

To select BL.O. Gobo Change, press the ENTER button to confirm. Use the UP/DOWN button

to select No (normal while changing gobo) or Yes (blackout while changing gobo), press the

ENTER button to store. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

Display Settings

Enter menu mode, select Display Settings, press the ENTER button to confirm, use the UP/DOWN

button to select Display Inverse, Backlight Auto Off, Backlight Intensity, Contrast Ratio,

Temperature Unit or Display Warning.

Display Inverse

Select Display Inverse, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select No (normal display) or Yes (inverse display), press

the ENTER button to store. Press the MENU button back to the last menu or let the unit idle

one minute to exit menu mode.

Backlight Auto Off

Select Backlight Auto Off, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select No or Yes, press the ENTER button to store. Press

the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Backlight Intensity

Select Backlight Intensity, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to adjust backlight intensity from 1 (dark) to 10 (bright),

press the ENTER button to store. Press the MENU button back to the last menu or let the unit

idle one minute to exit menu mode.

Contrast Ratio

Select Contrast Ratio, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to adjust value from 0to 30, press the ENTER button to

store. Press the MENU button back to the last menu or let the unit idle one minute to exit

menu mode.

Temperature Unit

Select Temperature Unit, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select

℃

℉

, press the ENTER button to store. Press

the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Display Warning

To select Display Warning, press the ENTER button to show the DISPLAY WARNING on the

display. Use the UP/DOWN button to select No (Normal) or Yes (display will show the error

warning when the unit went wrong), press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

Andere Handbücher für ENERGY SPOT XA-400 SPOT

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME IM-250 SP Bedienungsanleitung

ACME

ACME XP-5000SZ F Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME DMX512 Dynamic Scan Bedienungsanleitung

ACME

ACME TRACK 10 Bedienungsanleitung

ACME

ACME CP-18TC Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

ACME

ACME VOGUE Bedienungsanleitung

ACME

ACME Stage Par 220MP-220 Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

ACME

ACME Warrior Scan 50 LED-SC50C Bedienungsanleitung

ACME

ACME LED-SC25 Bedienungsanleitung

ACME

ACME Whack Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

ACME

ACME STAGE PAR 400 ZOOM IP Bedienungsanleitung

ACME

ACME LED-HC101 II Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME LED-767 RGBW Bedienungsanleitung

ACME

ACME SAMURAI SCAN 50 Bedienungsanleitung

ACME

ACME Energy Spot PRO Bedienungsanleitung

ACME

ACME Andromeda Bedienungsanleitung

ACME

ACME Inferno Bedienungsanleitung

ACME

ACME Beluga Bedienungsanleitung

ACME

ACME RAYZOR HYBRID Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung