ACME LED-HC101 II Bedienungsanleitung

LED-HC101 II

9. Fixture Cleaning

The cleaning of internal must be carried out periodically. Cleaning frequency

depends on the environment in which the fixture operates: damp, smoky or

particularly dirty surrounding can cause greater accumulation of dirt.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external at least every 20 days.

LED-HC101 II

User Manual

Please read the instructions carefully before use

Innovation, Quality, Performance

2014.05.10

毅丰

受控正本

LED-HC101 II

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. Function

4. Installation

5. DMX512 Address setting

6. How to control the fixture

7. DMX 512 Connection

8. Troubleshooting

9. Fixture Cleaning

LED-HC101 II

8. Troubleshooting

Following are a few common problems that may occur during operation. Here are

some suggestions for easy troubleshooting:

A. The fixture does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors and cables to see if link

properly.

2. If the DMX LED is on and no response to the channel, check the address

settings and DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or

on PCB of the fixture or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that

may cause damage or interference to DMX interface circuit.

C. No response to the sound

1. Make sure the fixture does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone.

10A

LED-HC101 II

7. DMX512 Connection

The DMX 512 is widely used in intelligent lighting control, with a maximum of 512

channels.

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120

ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug

and plug it in the DMX-output of the last unit.

3. Connect the unit together in a `daisy chain` by XLR plug from the output of the

unit to the input of the next unit. The cable can not branched or split to a `Y`

cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables,

soldered joints or corroded connectors can easily distort the signal and shut

down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX

circuit, when one of the units’ power is disconnected.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

LED-HC101 II

1. Safety Introductions

WARNING

yPlease keep this User Manual for future consultation. If you sell the fixture to

another user, be sure that they also receive this instruction booklet.

yUnpack and check carefully there is no transportation damage before using the

fixture.

yBefore operating, ensure that the voltage and frequency of power supply match

the power requirements of the fixture.

yDisconnect mains power before servicing and maintenance.

yIn the event of serious operating problem, stop using the fixture immediately.

Never try to repair the fixture by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized

technical assistance center. Always use the same type spare parts.

yDo not touch any wire during operation and there might be a hazard of electric

shock.

yTo prevent or reduce the risk of electrical shock or fire, do not expose the fixture

to rain or moisture.

yThere are no user serviceable parts inside the fixture. Do not open the housing

or attempt any repairs by yourself. In the unlikely event your fixture may require

service, please contact your nearest dealer.

Please read the instructions carefully which includes

important information about the installation, operation and

maintenance.

9A 2A

LED-HC101 II

2.Technical Specifications

yA compact LED controller for all kinds of DC 24V passive RGB Fixtures.

yCome with switch power supply inside

yBuilt-in programs under Master/Slave mode triggered by music.

y4 different ways of DMX addressing

yTerminals for linking LED-Wall Dimmer, and it provides power to LED Wall Dimmer.

yPower input: 120-240V~50/60Hz

yPower output: DC 24V

yMax Load：100W

yChannels

Channel 1 = Red

Channel 2 = Green

Channel 3 = Blue

Channel 4 = Dimmer / Strobe

yDimension：356 x 132 x 43 mm

yWeight：2kg

3. Function

1. DMX INTPUT: input DMX signal

2. DMX OUTPUT: output DMX signal

3. POWER SOCKET: for power input

4. LED: show the status of the unit

5. DIP SWITCH: used to set the start address of the unit or choose functions

6. AUTO DMX ADDRESS: used to set start address automatically.

7. LED-WD CONNECTOR: used to receive the signal of LED-WD only

8. SIGNAL OUTPUT: output signal and power for light

LED-HC101 II

C. Master/Slave operation

The fixture will allow you to link 16 fixtures together and operate without a controller.

In Master/Slave mode, the first fixture will control the others to give an automatic,

sound activated, synchronized light show. This function is good when you want an

instant show. The first fixture it’s DMX input cable will have nothing connect it, and

the other fixtures will be set in slave mode automatically. Their DMX input cables

connect the last fixture DMX output cable (daisy chain). Any fixture can act as a

Master or as a Slave

3A 8A

LED-HC101 II

6. How to control the fixture

There are three ways to control the fixture

A. Control by DIP switches

B. Control by Universal DMX controller

C. Master/Slave operation

A. Control by DIP switches

Dip switches setting Mode

Master

Slave

Sound

Chase

Use Dip switch 3, 4, 5 to choose chase speed (1-8)

Fade

Use Dip switch 3, 4, 5 to choose fade speed (1-8)

Color

Use Dip switch 6, 7, 8, 9 to choose color (16)

B. Control by universal DMX controller

If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin

adapter. The fixture uses four channels. Please refer to the following diagram to use

your controller to activate the fixture.

LED-HC101 II

4. Installation

1. Ensure that mains power supply is off before installing or wiring the LED fixture

2. Unscrew the screws and connect the wires as diagrams below

3. Tight the screws.

CAUTIONS：the LED controller total output power consumption is 100 watt.

5. DMX512 Address Setting

Each fixture needs to have a start address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). The

address, also know as the start channel, is the first channel used to receive

instructions from the controller.

There are four ways to set the fixture DMX start address:

A. DMX address setting by dip-switches

B. Auto DMX addressing

C. Remote DMX address setting by CA-T DMX TESTER

D. Remote DMX address setting by universal DMX controller

If you use the function B, C or D to set the DMX start address, the fixtures of

the chain all DIP switch MUST be set to OFF.

When you set the address by DMX controller and dip-switch at the same

time, the order of the DMX controller will be invalid.

7A 4A

LED-HC101 II

A. DMX address setting by dip-switches

1. Set the start address by dip-switch as the diagram below

2. Hold the AUTO DMX ADDRESS button for about 5 seconds, the LED

lights blinking indicating the address is set successfully.

Dip # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9 # 10

Value 1 2 4 8 16 32 64 128 256 Master/Slave

•Examples:

Channel 01：dip / on : # 1（=1）

Channel 05：dip / on : # 1, # 3（1+4=5）

Channel 09：dip / on : # 1, # 4 （1+8=9）

Channel 13：dip / on : # 1, # 3, # 4（1+4+8=13）

B. Auto DMX addressing

1. The DMX address of fixture can be set automatically. Set all dip-switches to OFF

and hold the AUTO DMX ADDRESS button of the first unit for about 5 seconds,

the fixture will be set the DMX start address to 1, and the other fixtures of the

chain will be set their own DMX start address automatically.

2. The LED fixtures use four channels, the next fixture’s will be automatic calculate

their own DMX address, not need to calculate the DMX channels of each fixture

in the chain. (Fixture 1 = 1, Fixture 2 = 5, Fixture 3 = 9, Fixture 4 = 13, Fixture…)

3. No need to turn the fixture off when you change the DMX address, as new DMX

address setting will be effect at once. Every time you turn the fixture on, it will be

ready to receive DMX signal or run the built-in programs.

LED-HC101 II

C. Remote DMX address setting by CA-T DMX TESTER

The fixture can be set the DMX address remotely by CA-T DMX TESTER. Please

refer to the CA-T user manual to set the DMX address to the fixture.

D. Remote DMX address setting by universal DMX controller

yMake sure the DMX cables of all units are connected.

yConnect the first unit to a universal DMX controller.

yConnect all units to the mains so they are switched on.

ySet all DMX-channels on your DMX-controller to zero (value 000).

ySet the DMX-channel, that you want to assign as DMX start address on you unit,

to maximum (value 255).

yPress the “Auto DMX address” button on the unit shortly.

yIf you want to set another unit to the same DMX start address, simply press it’s

“Auto DMX address” button and it will receive the same address.

yDone!

An example to make things clear:

yWe will set the DMX start address of a unit to 106:

yConnect the unit to the DMX-controller as described above and make sure all is

switched on.

ySet all DMX-channels on the controller to zero (000).

yNow set DMX-channel 106 to maximum (255).

yPress the “Auto DMX address” button on the unit shortly.

yDone! Your unit now has DMX address 106!

5A 6A

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Thunderroar Bedienungsanleitung

ACME

ACME Pageant CM-200Z Bedienungsanleitung

ACME

ACME Solaris Bedienungsanleitung

ACME

ACME LED-835B Bedienungsanleitung

ACME

ACME Gemini Bedienungsanleitung

ACME

ACME Dragon Scan 50 LED-SC50B Bedienungsanleitung

ACME

ACME Oxygen Bedienungsanleitung

ACME

ACME Whack Bedienungsanleitung

ACME

ACME CM-150 PAGEANT 150 Bedienungsanleitung

ACME

ACME CHIRON Bedienungsanleitung

ACME

ACME LED-SC252 Bedienungsanleitung

ACME

ACME STAGE PAR 100 COLOUR IP Bedienungsanleitung

ACME

ACME ColorTec 250 LED-CC60 Bedienungsanleitung

ACME

ACME DELUGE LED-WAV-50W Bedienungsanleitung

ACME

ACME Xperior XP-380 BEAM IP F Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME IP Cabin AR-01 Bedienungsanleitung

ACME

ACME HYGIEA Bedienungsanleitung

ACME

ACME XP-280 BS Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME BP-183 RGBW S R DXX Bedienungsanleitung

ACME

ACME STORM Bedienungsanleitung

ACME

ACME DMX512 Dynamic Scan Bedienungsanleitung

ACME

ACME CB-16TC Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung