ACME Thunderbreaker Bedienungsanleitung
CONTENTS
1. Safety Instructions ..................................................................................................2
2. Technical Specifications ..........................................................................................4
3. In Stallation and Splicing.........................................................................................6
4. Description..............................................................................................................8
4.1 Control Ption .....................................................................................................8
5. How To Set The Unit................................................................................................9
5.1 Main Function....................................................................................................9
6. Control By Universal DMX Controller ....................................................................18
6.1 DMX512 Connection ........................................................................................18
6.2 Address Setting ...............................................................................................19
6.3 DMX512 Configuration....................................................................................20
7. Troubleshooting ....................................................................................................50
8. Fixture Cleaning .....................................................................................................50
1C
1. Safety Instructions
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not
accept liability for any resulting defects or problems.
Unpack and check carefully that there is no transportation damage before using the unit.
The equipment is suitable for wet/indoor use.
DO install and operate by qualified operator.
DO NOT allow children to operate the fixture.
Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.
DO NOT connect the device to any dimmer pack.
Make sure there are no flammable materials close to the unit while operating to avoid fire hazard.
Examine the power wires carefully; replace them immediately if there is any damage.
DO NOT operate in dirty or dusty environment, do clean fixtures regularly.
DO NOT touch any wire during operation as there might be a hazard of electric shock.
Avoid power wires together twist other cables.
The minimum distance between light output and the illuminated surface must be more than 0.5
meters.
Please read the instruction carefully which includes important information about
the installation, usage and maintenance.
2C
Unit’s surface temperature may reach up to 75℃.DO NOT touch the housing bare-handed
during its operation.
In the event of serious operating problem, stop using the unit immediately.
Never turn on and off the unit time after time.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
DO NOT open the unit as there are no user serviceable parts inside.
Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage
or malfunction. Please contact the nearest authorized technical assistance center if needed.
Disconnect the mains power if the fixture is has not been used for a long time.
DO use the original packing materials before transporting it again.
DO NOT look directly at the light while the Luminaires is on.
DO NOT start on the unit without Luminaires enclosure or when housing is damaged.
Installation:
The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating and make sure that the structure to which
you are attaching the unit is secure and is able to support a weight of 10 times of the fixtures weight.
Always use a safety cable that can hold 12 times of the weight of the fixture when installing.
The equipment must be installed by professionals. It must be installed in a place where is out of the
reach of people and no one can pass by or under it.
3C
2. Technical Specifications
Power Voltage:
AC 100~240V, 50/60Hz
Power Consumption: 395w
Light Source:
576 x 0.8W RGBW LED
Beam Angle:
110°
Dimmer/Shutter:
Smooth dimming from 0-100%; outstanding strobe effect with variable speed
Control:
DMX Channel: 6+/11+/12+/13A+/13B+/17+/21A+/21B+/29+/37+/41+/53+ Channels
Protocols: DMX512, RDM
Firmware Upgrade via DMX link or USB disk
Construction:
Display: Color display
Data In/Out: 3-pin (5-pin XLR is optional)
Power In/Out: Power Connector in/out
Protection Rating: IPX4
Number of connected machines:
Maximum number of connected DMX machines: 32
Maximum number of power supply units: 120V, 60Hz: 4 units
230V, 50Hz: 8 units
Features:
• 144 zones can be controlled individually
• Black shell, no traces of screws
• Excellent, powerful and high output strobe effect
• The head and base are equipped with handles for easy carrying and transportation
• Can be spliced with each other or with THUNDER series lamps
4C
5C
Dimension/Weight:
503 x 183 x 318mm, 10.5kgs
19.8" x 7.2" x 12.5"in, 23.1lbs
3.Installation and splicing
The lamp should be fixed on the bracket with screws. Make sure that the installation is firm to prevent
vibration and slipping during operation. Also make sure that the brackets for the fixtures are stable and
can support more than 10 times the weight of the equipment. At the same time, when installing the
equipment, use a safety rope that can support 12 times the weight of the product.
The equipment must be installed by professionals. The equipment should be installed in a place where
the human body cannot be touched, and there will be no pedestrians passing by or sitting.
The installation height of the lamp is between 0~30M.
Installation method of single adjustable angle lamp hanger:
Installation method of lamp hanger:
How to install the lamp bolt:
The assembly method between the two lamps:
A
6C
：Installation method of lamp hanger (optional):
The splicing method of multiple
lamps：
Warning: Up to 7 units can be spliced in the vertical direction
7C
4.Description
4.1Control Panel
3 42
7 8
1
65
1. DISPLAY:To show the various menus and the selected function
2. POWER IN(POWERCON Version):
To connect to supply power
3. POWER OUT(POWERCON Version):
To connect to the next fixture
4. Button:
MENU
To enter into move backward or leave the menu
UP
To go backward to move up in the menu
DOWN
To go forward to move down in the menu
ENTER
To perform the desired functions
5. DMX IN:
DMX512 link, use 3-pin XLR cable to link the unit and DMX controller (5-pin XLR is optional)
6. DMX OUT:
DMX 512 operation, use 3-pin XLR cable to link the next units (5-pin XLR is optional)
7. Ethernet interface:connect to the network.
8. Ethernet interface: connect to the network.
8C
5.How To Set The Unit
5.1 Main Function
Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until
the required function is shown on the monitor. Select the function by the ENTER button. Use the
UP/DOWN button to choose the submenu, press the ENTER button to store and automatically
return to the last menu. Press the MENU button or let the unit idle One minuteto exit menu mode.
The main functions are shown below:
9C
Inhaltsverzeichnis
Andere ACME Beleuchtungsausrüstung Handbücher
ACME
ACME Energy Spot PRO Bedienungsanleitung
ACME
ACME Xperior XP-380 BEAM IP F Bedienungsanleitung
ACME
ACME Thunder Bedienungsanleitung
ACME
ACME Xperior 700SZ Spot Bedienungsanleitung
ACME
ACME GEIST BSWF Bedienungsanleitung
ACME
ACME Thunderroar Bedienungsanleitung
ACME
ACME Dynamic 25 Spin LED?GF25 Bedienungsanleitung
ACME
ACME Xperior 1500SZ Bedienungsanleitung
ACME
ACME DMX512 Dynamic Scan Bedienungsanleitung
ACME
ACME LS-1005 Bedienungsanleitung
ACME
ACME iSolution Bedienungsanleitung
ACME
ACME V Inground VI-10QW Bedienungsanleitung
ACME
ACME Sandane Bedienungsanleitung
ACME
ACME LP-1600 BD30 Bedienungsanleitung
ACME
ACME PIXEL LINE IP Bedienungsanleitung
ACME
ACME SAMURAI SCAN 50 Bedienungsanleitung
ACME
ACME XP-5000WZ Bedienungsanleitung
ACME
ACME FLASHDOT Bedienungsanleitung
ACME
ACME VENOM LED-460 Bedienungsanleitung
ACME
ACME Gemini Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
