ACME LED-SC252 Bedienungsanleitung

LED-SC252

User Manual

Please read the instruction carefully before use

CONTENTS

1. Safety Instructions....................................................................................................2

2. Technical Specifications............................................................................................3

3. How To Set The Unit .................................................................................................4

3.1 Control Panel ......................................................................................................4

4. How To Control The Unit ..........................................................................................5

4.1 Master/Slave Built In Preprogrammed Function ................................................5

4.2 Easy Controller....................................................................................................6

4.3 DMX Controller...................................................................................................6

5. DMX 512 Configuration ............................................................................................7

6. DMX512 Connection ................................................................................................9

7. Troubleshooting..................................................................................................... 11

8. Fixture Cleaning..................................................................................................... 12

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cables when fixing this unit.

Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature

is higher than this.

Turn off the power and allow about 15 minutes for the unit to cool down before servicing.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

The housing and lenses must be replaced if they are visibly damaged.

Please read the instruction carefully which includes important information

about the installation, usage and maintenance.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Make sure that the structure to which

you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be installed by professionals. It must be fixed at a place where is out of the

reach of people and no one pass by or under it.

2. Technical Specifications

Featuring 1.8 stepping motors, latest LED technology, the Dynamic 25 Dual Scan delivers

outstanding active effects

10 DMX channels: pan, tilt, gob, strobe, dimmer for each head

Gobo/color wheel with 8 gobos/colors plus open

Smooth dimming and variable strobe speeds

3 operation modes: DMX, Master/Slave, Sound Active

Great built-in programs in Master/Slave mode triggered by music

Optional easy controller CA-8 or CA-9 RX for instant lighting shows

Ideal for clubs, bars, discos, parties and mobile DJs

◇Power Voltage: AC 100V~240V, 50/60Hz

◇Power Consumption: 96W

◇Power Cable Daisy Chains: 7 Fixtures Max. (230V, 50Hz)

4FixturesMax.(120V,60Hz)

◇LED Sources: 2×25WCREELEDs

◇BeamAngle: 16°

◇Weight: 6.5Kgs

◇Dimension: 351 × 283 × 231mm

3. How To Set The Unit

3.1 Control Panel

1. DMX IN:

DMX512 link, use 3-pin XLR cable to link the unit and the DMX controller;

2. DMX OUT:

DMX512 link, use 3-pin XLR cable to link the next unit and output the DMX signal;

3. ONLY FOR REMOTE CONTROL:

Connects with the optional CA-8 to control the unit;

4. ONLY FOR WIRELESS RECEIVER:

Connects with the optional CA-9 RX to control the unit;

5. MICROPHONE:

Receives music signals for sound active mode;

6. DIP SWITCH:

Manually set the start DMX address;

7. FUSE (T 3.15A):

Protects the unit from over-voltage or short circuit;

8. POWER OUT:

Connects to the next fixture;

9. POWER IN:

Connects to power supply;

4. How To Control The Unit

You can operate the unit in three ways:

1. Master/slave built-in preprogram function

2. Easy controller (optional CA-8)

3. Universal DMX controller

You do not need to turn the unit off when you change the DMX address, the new DMX address

setting will take effect immediately.

4.1 Master/Slave Built In Preprogrammed Function

The unit can be linked together in daisy chain as many as you need in master/slave mode to

perform the great built-in pre-programmed lighting shows triggered by music.

In Master/Slave mode refer to the DMX settings below:

Master unit: DMX start address MUST be set to 001. (First DIP switch = ON, all other are OFF)

Slave units: DMX start address may have any value but NOT 001 (example: set the first 3 DIP

switches to ON)

﹡Dipswitch 2 “ON” has two functions:

1. Perform the built-in pre-programmed by music.

2. Auto mode: Eight Chase(At this mode press dip switch 3 will change the direction of rotation，

press dip switch 4,5,6 will change the speed)

﹡2-light show

Dipswitch 10”off” means the unit works normally and “on” means inversion. In order to create a

great light show, you can set dip switch 10 ”on” on any unit that is linking to the master unit to get

contrast movement to the master unit, even if you have two units only. Dipswitch 10 on the first

(Master) unit is no use for the 2-light show as it is the master unit that operates the light show.

4.2 Easy Controller

The easy CA-8 remote control is used only in master/slave mode. By connecting to the

1/4” jack socket of the first unit. You will find that the remote control in the first unit

will control all the other units for Stand by, Function and Mode selection.

Stand by

Blackout the unit

Function

1. Sync. strobe

2. Async. strobe

3. Sound strobe

Select

Movement

0-31

Color/Goboselection

1. Press shortly for

color change.

2. Hold on for Gobo

change

Mode

Sound

(LED OFF)

Movement

(LED Blinking)

Gobo/Color

(LED ON)

4.3 DMX Controller

When using a universal DMX controller to control the chain of units, you have to set DMX address

by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal. Dip switch 10 is

used to select channel mode, it’s ON means 1 channel mode and OFF means 3 channel mode.

Please refer to the following diagram to know how to address your DMX 512 system in the binary

code.

DMX 512 Address Chart:

Dip-switches # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9 #10

Value 1 2 4 8 16 32 64 128 256 2-Light Show

•Examples:

10-CH mode: (Dip switch 10 ON)

Channel 1: dip / on: #1 (=1)

Channel 2: dip / on: #1, #2, #4 (1+2+8=11)

Channel 3: dip / on: #1, #3, #5 (1+4+16=21)

Channel 4: dip / on: #1, #2, #3, #4, #5 (1+2+4+8+16=31)

5. DMX 512 Configuration

10 Channels Mode:

CHANNEL VALUE FUNCTION

1 0 – 255

PAN 1

0° - 180°

2 0 – 255

TILT 1

0° - 70°

0 –7

8 – 15

16 – 131

132 – 139

140 – 181

182 – 189

190 – 231

232 – 239

240 – 247

248 – 255

STROBE 1

Blackout

Open

Strobe, slow fast

Open

Fast open, slow close

Open

Fast close, slow open

Open

Random strobe

Open

0 – 7

8 – 14

15 – 21

22 – 28

29 – 35

36 – 42

43 – 49

50 – 56

57 – 63

64 – 71

72 – 78

79 – 85

86 – 92

93 – 99

100 – 106

107 – 113

114 – 120

121 – 127

128 – 255

GOBO 1

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Open shaking

Gobo 1 shaking

Gobo 2 shaking

Gobo 3 shaking

Gobo 4 shaking

Gobo 5 shaking

Gobo 6 shaking

Gobo 7 shaking

Gobo 8 shaking

Gobo rotation, slow fast

5 0 – 255

DIMMER 1

0% 100%

6 0 – 255

PAN 2

0° - 180°

7 0 – 255

TILT 2

0° - 70°

0 –7

8 – 15

16 – 131

132 – 139

140 – 181

182 – 189

190 – 231

232 – 239

240 – 247

248 – 255

STROBE 2

Blackout

Open

Strobe, slow fast

Open

Fast open, slow close

Open

Fast close, slow open

Open

Random strobe

Open

0 – 7

8 – 14

15 – 21

22 – 28

29 – 35

GOBO 2

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

36 – 42

43 – 49

50 – 56

57 – 63

64 – 71

72 – 78

79 – 85

86 – 92

93 – 99

100 – 106

107 – 113

114 – 120

121 – 127

128 – 255

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Open shaking

Gobo 1 shaking

Gobo 2 shaking

Gobo 3 shaking

Gobo 4 shaking

Gobo 5 shaking

Gobo 6 shaking

Gobo 7 shaking

Gobo 8 shaking

Gobo rotation, slow fast

5 0 – 255

DIMMER 2

0% 100%

6. DMX512 Connection

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME GLAMOUR 700Z RGBY Bedienungsanleitung

ACME

ACME Uploader II Bedienungsanleitung

ACME

ACME BRIGHT Bedienungsanleitung

ACME

ACME Dynamic 25 Roller LED-SC25B Bedienungsanleitung

ACME

ACME ASTRO LED-256D Bedienungsanleitung

ACME

ACME LED-HC50 II Bedienungsanleitung

ACME

ACME VOGUE Bedienungsanleitung

ACME

ACME CM-150 PAGEANT 150 Bedienungsanleitung

ACME

ACME CB-16TC Bedienungsanleitung

ACME

ACME V Inground VI-10QW Bedienungsanleitung

ACME

ACME CHIRON Bedienungsanleitung

ACME

ACME GLORV FRAMING XP-5000SZF Bedienungsanleitung

ACME

ACME LED-WAV-10W Bedienungsanleitung

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME Splendor 220 II Bedienungsanleitung

ACME

ACME Andromeda Bedienungsanleitung

ACME

ACME BTDG40 Bedienungsanleitung

ACME

ACME Sunrise Bedienungsanleitung

ACME

ACME CA-DC6S Bedienungsanleitung

ACME

ACME BIG BANG Bedienungsanleitung

ACME

ACME BOOTES Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME HYGIEA Bedienungsanleitung

ACME

ACME Building wash Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung