ACME MP-12FC Bedienungsanleitung

S TAG E TRI-PAR 12FC

MP-12FC

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. How To Set The Fixture

4. How To Control The Fixture

5. DMX 512 Configuration

6. DMX 512 Connections

7. Troubleshooting

8. Fixture Cleaning

1 A

1. Safety Introductions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user,

be sure that they also receive this instruction booklet.

All fixtures are intact from the manufacturer, please operate follow up the user manual,

artificial fault are not under guarantee repair.

Unpack and check carefully that there is no transportation damage before using the

unit.

The unit is for indoor use only. Use only in a dry location.

Do install and operate by operator.

Use safety chain when fixes the unit. Don’t handle the unit by taking its head only, but

always by taking its base.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

Maximum ambient temperature TA : 40℃. Don’t operate it where the temperature is

higher than this.

Don’t connect the device to any dimmer pack.

First run, there will be smoke or smells, and all disappearing a few minutes later.

Make sure there are no flammable materials close to the unit while operating, as it is

fire hazard.

Look over power wires carefully, replace immediately if there is any damage.

Never run on for a long time lest shortening lifespan.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happen,

cut off the mains power immediately.

Do not operate in dirty and dusty environment, also cleaning fixtures regularly.

Do not allow children to operate the fixture.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

2 A

Do not touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together arounding other cables.

Disconnect mains power before fuse/lamp replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Do not open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead

to damage or malfunction. Please contact the nearest authorized technical assistance

center.

Disconnect the mains power if the fixture is not used for a long time.

Do use original packing materials once transport it again.

Do not look directly at the LED light beam while the fixture is on.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

2. Technical Specifications

Voltage：AC100V-240V

LED: 12*10Quad-color LED

Fuse: T 6.3A

Power consumption

：

156W

3 A

Dimension

：

250 x 327 x 215 mm

Weight

：

6kg

3. How To Set The Fixture

3.1 Control Panel

○

1E A Display: To show the various menus and the selected functions

○

2E A LED:

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

4 A

○

3E A Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

○

4E A DMX output: For DMX512 link, use 3-pin XLR plug cable to link the next unit.

○

5E ADMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

○

6E A Mains output: Connect to supply power for the unit.

3.2 Main Function

To select any functions, press MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press ENTER button to

setup or it will automatically return to the main functions without any change after idling

7seconds. Back to the functions without any change press MENU button. The main

functions are shown below:

5 A

Fixture Hours

DMX512Address Setting

Blackout Mode " No Blackout "

Blackout Mode "Yes Blackout "

Software Version

Inversion

LED off

Sound Mode on

Sound Mode off

LED on

Self-Test

Show mode

Normal

Channels Mode

Master/Slave mode

FixtureTemperature

White balance

Manual mode

Dimmer mode 1

Dimmer mode 4

6 A

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to change the DMX 512 address.

Once the address has been selected, press ENTER button to setup or automatically exit

menu mode without any change after 7seconds. Back to the previous functions without any

change press MENU button.

Channel Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (4

channels mode) or (5 channels mode) or (8 channels mode). Once the

mode has been selected, press the ENTER button to setup or automatically exit menu mode

without any change after 7seconds To go back to the functions without any change press

the MENU button.

Slave Mode

Press the MENU button up to when the is showing on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select the (normal)

or (slave 2) mode. Once the mode has been selected, press the ENTER button to

setup or automatically return to the main functions without any change after7seconds. To go

back to the functions without any change press the MENU button again.

Show Mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (Random show) or (color)

or (fade), if you select the color or fade mode, press ENTER button to confirm, and

use DOWN and UP button to select color 1-10 or fade speed (speed 1: slow, speed 2:

middle, speed 3: fast). Once select, press ENTER button to setup or automatically exit menu

mode without any change after 7seconds. To go back to the last function without any

7 A

change press the MENU button.

Dimmer Mode

Press the MENU button up to when is showing on the display. Pressing the ENTER

button and the display will blink. Use the DOWN and UP buttons to select the

(Dimmer Mode 1: Optically Linear) or (Dimmer mode 2: Square Law) or

(Dimmer mode 3: Inverse Square Law) or (Dimmer mode 4: S-cure) mode. Once

the mode has been selected, press the ENTER button to setup or automatically return to the

main functions without any change after one minute. To go back to the functions without any

change press the MENU button again.

Optically Linear: The increase in light intensity appears to be linear as DMX value is

increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

S-cure: Light intensity control is finger at low levels and high levels and coarser at medium

levels.

Sound mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (sound on) or (sound off).

Once select, press ENTER button to setup or automatically exit menu mode without any

change after 7seconds. To go back to the functions without any change press the MENU

button

8 A

Blackout mode

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, Use DOWN and UP button to select the (blackout) or (normal).

Once select, press ENTER button to setup or automatically exit menu mode without any

change after 7seconds. To go back to the functions without any change press the MENU

button

LED display

Press the MENU button up to when the is shown on the display. Pressing ENTER

button and the display will blink. Use DOWN and UP button to select (display

always on) or (display off 20 seconds after exit menu) mode. Once select, press

ENTER button to setup or exit menu mode without any change after 7seconds. Back to the

functions without any change press MENU button again.

Display Inverse

Press MENU button until is blinking on the display. Use DOWN and UP button to

select (display normal) or (display inverse), press ENTER button to setup.

Back to the functions without any change press MENU button.

White Balance

Press the MENU button up to when the is shown on the display. Pressing ENTER

button, and use DOWN and UP button to select , or , press ENTER

button to confirm and use DOWN and UP button to adjust the value between 125 and 255,

once select press ENTER button to setup or automatically exit menu mode without any

change after 7seconds. To go back to the last function without any change press the MENU

button.

Manual setting color

Press the MENU button up to when the is shown on the display. Pressing ENTER

9 A

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME Xperior XP-380 BEAM IP F Bedienungsanleitung

ACME

ACME ColorTec 250 LED-CC60 Bedienungsanleitung

ACME

ACME STORM Bedienungsanleitung

ACME

ACME GEIST BSWF Bedienungsanleitung

ACME

ACME Splendor 220 II Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME LED-PS10D RGBW Bedienungsanleitung

ACME

ACME IM-250 SP Bedienungsanleitung

ACME

ACME Ozone 3 Bedienungsanleitung

ACME

ACME CM-150 PAGEANT 150 Bedienungsanleitung

ACME

ACME LED-3082 RGB Bedienungsanleitung

ACME

ACME SABER Mini Bedienungsanleitung

ACME

ACME V Inground VI-10QW Bedienungsanleitung

ACME

ACME LED-835B Bedienungsanleitung

ACME

ACME XP-5000SZ F Bedienungsanleitung

ACME

ACME CRUX Bedienungsanleitung

ACME

ACME LP-1600 BD30 Bedienungsanleitung

ACME

ACME Xperior 700SZ Spot Bedienungsanleitung

ACME

ACME Stage Par 220MP-220 Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

ACME

ACME TV LIGHT PANEL 2000 Bedienungsanleitung

ACME

ACME Whack Bedienungsanleitung

ACME

ACME LED-900 A Bedienungsanleitung

ACME

ACME LED-PS10 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung