ACME Splendor 220 II Bedienungsanleitung

User Manual

Please read the instruc on carefully before use

CM-220 II

2019.05.13

审核

受控正本

TABLE OF CONTENTS

1. Safety Instruction..........................................................................2

2. Technical Specification.................................................................3

3. Change Beam Angle....................................................................4

4. How To Set The Unit....................................................................4

4.1 Control Panel........................................................................4

4.2 Main Function.......................................................................5

4.3 Home Position Adjustment...................................................9

5. How To Control The Unit............................................................ 10

5.1 Master/Slave Built-in Preprogram Function........................10

5.2 DMX Controller................................................................... 10

5.4 DMX 512 Configuration...................................................... 11

5.5 DMX512 Connection.......................................................... 12

6. Troubleshooting..........................................................................13

7. Fixture Cleaning......................................................................... 14

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire

hazard.

Use safety cable when fixes this unit.

Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is

higher than this.

In the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

Do not touch any wire during operation as high voltage might be causing electric shock.

Warning

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

Do not open the unit within five minutes after switching off.

The housing, the lenses must be replaced if they are visibly damaged.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

Please read carefully the instruction, which includes important

information about the installation, usage and maintenance.

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Installation

The unit should be mounted via its metal hole on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a 10 times

weight of the unit.

2. Technical Specification

Splendor 220 II features 22 high-power LEDs with the capability of producing full

range of color mixing. Its compact, lightweight design and powerful output make it

ideal for all kinds of applications.

◆DMX Channels:9/16 channels

◆2 operation modes: DMX, Master/Slave

◆Great built-in lighting shows under Master/Slave mode

◆Blue LCD display for easy navigation

◆Perfect for stage, theatre, TV, production, rental and discotheques.

Voltage

：

AC 100-240V~50/60Hz

Power consumption: 180W

Light Source: 22x5W RGBW LED (4 in 1)

Fuse: T 3.15A

Beam angle: 20°

Dimension/Weight: 326 x 243.5 x 350 mm，9.2kgs

12.8"x9.6"x13.8"in，20.3lbs

3. Change Beam Angle

If you want to change the beam angle of the fixture, you can change lens of the

fixture refer to the photo below:

4. How To Set The Unit

4.1 Control Panel

Wire Version

：

12345678

POWERCON Version

：

Turn off the mains power

first, or high voltage may

cause electric shock!

1.LED

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

POWER On Power input present

2. Display

To show the various menus and the selected functions

3.Button

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

4. POWER SWITCH (Wire Version):

Turns On/Off the power

5. Mains input

Connect to supply mains power.

6. Fuse(T3.15A):

For over current protection.

7. DMX IN:

DMX 512 link, use 3-pin XLR cable to link the unit and DMX controller

8. DMX OUT:

DMX 512 operation, use 5-pin XLR cable to link the next units

4.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected,

Press ENTER button to store. Back to the main functions without any change press the

MENU button or wait for one minute.

Hold MENU button to quit menu mode, the unit will run the built-in program you selected.

The main functions are shown below:

AutoTest

Fixture Settings

Show1

Show2

Show3

Show4

Show Mode

Slave 1

Slave 2

Slave Mode

Yes

Black Out

Yes

Pan Inverse

Tilt Inverse No

Yes

Back Light Off

Yes

Display Inverse

Temperature Unit

DmxAddress 1~512

Channel Mode Mode 1 (9)

Mode 2 (16)

Pan

Tilt

Red

Green

Blue

White

Strobe

Dimmer

ManualTest 0~255

White Balance

Red

Green

Blue

125~255

Master

Reset

Yes

DimmerSpeed

°F

CPU-A

DMX Address

Press the MENU button up to when the DMX Address is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to change the DMX512

address. Once the address has been selected, press the ENTER button to store. Back to

the main functions without any change press the MENU button or wait for one minute.

Channel Mode

Press the MENU button up to when the Channel Mode is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to select the Mode 1 (9)

or Mode 2 (16). Once selected, press the ENTER button to store. Back to the main functions

without any change press the MENU button or wait for one minute.

Show Mode

Press the MENU button up to when the Show Mode is showing on the display. Press

ENTER button, the display will blink. Press DOWN and UP button to select Show 1 or Show

2 or Show 3 or Show 4, once selected, press the ENTER button to store. Back to the main

functions without any change press the MENU button or wait for one minute.

Slave Mode

Press the MENU button up to when the Slave Mode is showing on the display. Press

ENTER button and the display will blink. Use DOWN and UP button to select the Master or

slave 1 or slave 2 mode. Once selected, press the ENTER button to store. Back to the main

functions without any change press the MENU button or wait for one minute.

Black Out

Press the MENU button up to when the Black Out is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the yes (yes

blackout) or no (no blackout) mode. Once selected, press the ENTER button to store. Back

to the main functions without any change press the MENU button or wait for one minute.

Pan Inverse

Press the MENU button up to when the Pan Inverse is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the No

(Normal) or Yes (pan inverse) mode. Once selected, press the ENTER button to store. Back

to the main functions without any change press the MENU button or wait for one minute.

Tilt Inverse

Press the MENU button up to when the Tilt Inverse is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the No

(Normal) or Yes (pan inverse) mode. Once selected, press the ENTER button to store. Back

to the main functions without any change press the MENU button or wait for one minute.

Dimmer Speed

Press the MENU button up to when the Dimmer Speed is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the No

(Normal) or Yes (dimmer speed) mode. Once selected, press the ENTER button to store.

Back to the main functions without any change press the MENU button or wait for one

minute.

Back Light

Press the MENU button up to when the Back Light is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the on (back

light on) or off (back light off 1 minute after auto show) mode. Once selected, press the

ENTER button to store. Back to the main functions without any change press the MENU

button or wait for one minute.

Contrast Ratio

Press the MENU button up to when the Contrast Ratio is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to adjust value 0 to 30.

Once selected, press the ENTER button to store. Back to the main functions without any

change press the MENU button or wait for one minute.

Display Inverse

Press the MENU button up to when the Display Inverse is showing on the display. Pressing

ENTER button and the display will blink. Use DOWN and UP button to select the No

(Normal) or Yes (display inverse) mode. Once selected, press the ENTER button to store.

Back to the main functions without any change press the MENU button or wait for one

minute.

Auto Test

Press the MENU button up to when the Auto Test is showing on the display. Pressing

ENTER button and the display will show Test… and the unit will run self-test by built-in

program. To go back to the functions press the MENU button.

Manual Test

Press the MENU button up to when the Manual Test is showing on the display. Press

ENTER button and Pan will blink, use UP and DOWN button to choose Tilt or Red or Green

or White or Strobe or Dimmer, press ENTER button to enter, then press UP and Down

button to adjust the value and press ENTER button to set next optional. Back to the main

functions without any change please press the MENU button.

White Balance

Press the MENU button up to when the White Balance is showing on the display. Press

ENTER button and the Red will blink, press UP and Down button to adjust the value, press

ENTER button to store and Green will blink on the display, press UP and Down button to

adjust the value, press ENTER button to store and Blue will blink on the display, press UP

and Down button to adjust the value, and press ENTER button to store. Back to the main

functions without any change please press the MENU button.

Temperature Unit

Press the MENU button up to when the Temperature Unit is showing on the display.

Pressing ENTER button and the display will blink. Use DOWN and UP button to select ℃

or ℉. Once selected, press the ENTER button to store. Back to the main functions without

any change press the MENU button or wait for one minute.

Fixture Information

Press the MENU button up to when the Fixture Information is showing on the display.

Pressing ENTER button and the display will blink. Use DOWN and UP button to select

Fixture Use Hours or CPU-A. Once selected, press the ENTER button to store. Back to the

main functions without any change press the MENU button or wait for one minute.

Fixture Settings

Press the MENU button up to when the Fixture Settings is showing on the display. Use

DOWN and UP button to select Yes (the fixture will restore to factory settings) or No, and press

ENTER button to store. Back to the main functions without any change press the MENU

button or wait for one minute.

Reset

Press the MENU button up to when the Reset is blinking on the display. Pressing ENTER

button and all motors will back to their home position. To go back to the functions press the

MENU button.

4.3 Home Position Adjustment

Press the MENU button into menu mode, then press and hold the ENTER button for about 3

seconds into offset mode to adjust the home position. Select the function by the ENTER

button. Use the UP/DOWN button to select the submenu, press the ENTER button to store

and automatically return to the last menu. Press the MENU button to exit.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME DMX512 Dynamic Scan Bedienungsanleitung

ACME

ACME Whack Bedienungsanleitung

ACME

ACME VENOM LED-460 Bedienungsanleitung

ACME

ACME Stage Par 220MP-220 Bedienungsanleitung

ACME

ACME Sunrise Bedienungsanleitung

ACME

ACME ANIMA C Bedienungsanleitung

ACME

ACME SABER HYBRID PRO Bedienungsanleitung

ACME

ACME DELUGE LED-WAV-50W Bedienungsanleitung

ACME

ACME BOOTES Bedienungsanleitung

ACME

ACME CB-16TC Bedienungsanleitung

ACME

ACME LED-275 D Bedienungsanleitung

ACME

ACME LED-3082 RGB Bedienungsanleitung

ACME

ACME V Inground VI-10QW Bedienungsanleitung

ACME

ACME Diamonds II Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

ACME

ACME LED-900 A Bedienungsanleitung

ACME

ACME ColorTec 250 LED-CC60 Bedienungsanleitung

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME LED-212RGB Bedienungsanleitung

ACME

ACME PEXEL 100 Bedienungsanleitung

ACME

ACME Sandane Bedienungsanleitung

ACME

ACME COOLIE 14FC Bedienungsanleitung

ACME

ACME Libre Bedienungsanleitung

ACME

ACME LED-HC101 II Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung