ACTi ACM-8511 Kurzanleitung

www.acti.com

ACTi

Knowledge Base

Category: Installation & Configuration Note

Sub-category: Streaming & Networking; Preview; Integration; Application

Model: ACM-8511,ACM-82X1

Firmware: N/A

Software: N/A

Author: Athena.Tsai

Published: 2010/04/07

Reviewed: 2010/06/25

How to Configure PTZ Functions

Contents

Introduction

Functions of PTZ camera

。Manually PTZ

。Preset points

。Auto scan

。Preset tour

Introduction

PTZ (pan, tilt, and zoom) cameras are devices that can be moved left and right (pan), up and

down (tilt), and zoom in and out.Why do we need PTZ camera? There are several advantages

of PTZ camera.

First of all, it can be remotely controlled to pan, tilt and zoom.Wherever you are, you can easily

adjust the camera toward the area you want to monitor without going to the site where the

camera is. Furthermore, the preset functions allows you to monitor multiple areas as long as

the camera can point to the right direction. This function greatly increases the flexibility of your

video surveillance system.

You also can set schedules for the PTZ camera to monitor several different areas in turn. For

example, you may want to monitor the whole area in the day time, but just the entrance during

the night as no one should show up there. You just need to make preset points for these two

different areas and make a tour to let your camera move between them.

In the following chapter, we are going to show you how to configure PTZ functions including

manual PTZ, preset points, auto scan, and preset tour.

www.acti.com

Functions of PTZ Camera

Manual PTZ

You can use PTZ control panel to remotely control the camera.

a. Via web configurator

Click ‘PTZ’. The PTZ control panel will pop up. You can use it to pan, tilt, and

zoom in and out.Besides those, you also can control the speed of panning tilting,

and zooming.

www.acti.com

b. Via NVR

First, you have to enable PTZ function and choose the correct model and

protocol. Press apply and restart ActiveSetup.

Open ActiveMonitor. You will be able to use the control panel on the left side to

control the camera to pan, tilt, and zoom.

www.acti.com

Preset points

You may have many places to monitor for your PTZ camera. You can use this

function to let your camera switch between the preset areas. Then you can go to

these preset points by scheduled time or by certain events.

For example, if you want to monitor the platform of a train station, you may want to

see not only the whole area, but also some cetain spots for different needs.Then you

can schedule an event and make the camera to monitor the platform during the day

time and move to another certain spot during the night time. (Note: If you need to

know how to schedule or configure a event, please reference the document

http://www.acti.com/support/KnowledgeBase/outside/detail.asp?KB_ID=KB20100125001.)

Now, you have to know how to set preset points and you will know how to make a

tour for preset points in the last section.

a. Via web configurator

First, you have to use PTZ control panel to adjust the camera and aim at the

area you want to monitor.

After completing the adjustment, click ‘Preset’button to go to the preset page.

You can choose any number and then click the corresponding ‘Set’button. You

www.acti.com

also have to set up the name. After that, you’ve done all the settings of one

preset point. If you need to set up another preset point, please repeat the steps

from the last step to this one.

After all the settings are done, go back to PTZ page.You will be able to use these

preset points by clicking the number ID and shift your view to that preset point.

www.acti.com

b. Via NVR

1. Go to ActiveSetup / PTZ Preset.

2. Click ‘Live View’to get the real time video

3. Use ‘PTZ Operation’to adjust the camera

4. Choose the number and enter the name you want. Click the Check mark to

remember it.This will setup the PTZ preset point.

Go back to Active Monitor, and you will see the entry you set is in the ‘Goto’check list.

Afterward, you can use it and go to the preset points easily.

www.acti.com

Auto Scan

If the function auto scan is enabled, the camera would pan left to right continuously

to scan the whole area.

a. Via web configurator

The auto scan control is under PTZ -> Other Controls. You also can set the

speed for auto scan.

b. Via NVR

Choose ‘Start Scan’, then it will start to scan.

Note:We suggest you avoid continuous auto scan unless really needed, and use preset points

instead.The reason of it is that the non-stop movement puts a lot of stress on the it may reduce

the life of your PTZ camera. It’s like if you keep running a machine (ex: a car is driven

continuously for a long time), the machinery part would possibly wear away sooner than if you

give it some rest in between activities.

www.acti.com

Preset Tour

You can assign several preset points, and link them in a tour to monitor each area for

the duration you want. For example, in the warehouse, you would want to both see

the overview and focus on a certain production line. Therefore, you have to set

thoses areas as preset points. And then you can make them a tour and set the time

to patrol them. The camera will then monitor different areas according to your

assigned schedule. If you set four preset points for the tour, it will go from number

one to four, and go back to number one and run to four, over and over again. Tours

can be triggered by event or run on scheduled time. Please reference the document

(http://www.acti.com/support/KnowledgeBase/outside/detail.asp?KB_ID=KB201001

25001) for how to configure an event.

a. Via web configurator

1. Set the preset points that you want to monitor

2. (1)Choose a tour

(2)Click Edit

www.acti.com

3. Make a tour by configuring the sequence of the preset points and the time.

(1) Choose one preset point

(2) Set the time interval that you want camera to moniter the area

(3) Click add(+) button

(4) When you finish setting, don’t forget to save it

4. If you need to adjust the sequence, you can use the buttons as below.

www.acti.com

b. Via NVR

(1) Set the preset points. Then you can see the setting in ActiveSetup and

ActiveMonitor

Figure: (left) ActiveSetup; (right)ActiveMonitor

(2) Go to ActiveSetup and Preset Tour page. Secondly, set the tour name and

click ‘Apply.’Then you can see the entry you set in the tour list.

Andere Handbücher für ACM-8511

Dieses Handbuch passt für folgende Modelle

Andere ACTi Sicherheitskamera Handbücher

ACTi

ACTi ACM-1431 Bedienungsanleitung

ACTi

ACTi I91 Bedienungsanleitung

ACTi

ACTi ACM-7511 Bedienungsanleitung

ACTi

ACTi D71 Bedienungsanleitung

ACTi

ACTi E77 Bedienungsanleitung

ACTi

ACTi i51 Bedienungsanleitung

ACTi

ACTi A950 Bedienungsanleitung

ACTi

ACTi PCDK Camera Demo Kit Bedienungsanleitung

ACTi

ACTi D71 Bedienungsanleitung

ACTi

ACTi E12 Bedienungsanleitung

ACTi

ACTi ACM-3401 Series Gebrauchsanweisung

ACTi

ACTi Z41 Bedienungsanleitung

ACTi

ACTi B21 Bedienungsanleitung

ACTi

ACTi ACM-7511 Gebrauchsanweisung

ACTi

ACTi D7 Series Bedienungsanleitung

ACTi

ACTi A713 Bedienungsanleitung

ACTi

ACTi E77 Bedienungsanleitung

ACTi

ACTi ACM-1100 Series Bedienungsanleitung

ACTi

ACTi D71 Montageanleitung

ACTi

ACTi VMGB-352 Bedienungsanleitung

ACTi

ACTi ACM-1230 Series Bedienungsanleitung

ACTi

ACTi I98 Bedienungsanleitung

ACTi

ACTi B915 Bedienungsanleitung

ACTi

ACTi Q11 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung