ACTi Q960 Bedienungsanleitung
People Counting Camera
Installation Guide
Q960, Q961, Q962
2019/08/02
www.acti.com
INSTALLATION GUIDE
2
The following documentation covers the installation and configuration of your
device.
NOTE: The accuracy of the analytics algorithm may be affected by different
environmental factors or inappropriate installation. Please follow the
procedures in this installation guide. ACTi will not be held liable for
inaccuracies resulting from the aforesaid causes.
Part 1: Installation Specification
1.
Model and counting width
The counting width depends on the installation height. The recommended
installation height for dual-lens camera is less than 4.0m (13.1ft). The specific
corresponding relation shown below:
Model
Installation
height
（m/ft）
Max. counting
width
（m/ft）
Without
doorframe
With doorframe
Q960
2.5/8.2
1.8/5.9
Placed in the middle
0.68m(2.2ft)
to door
Placed in the middle
3.0/9.8
2.9/9.5
Placed in the middle
1.1m(3.6ft)
to door
Placed in the middle
3.5/11.5
4.0/13.1
Placed in the middle
1.52m(5.0ft)
to door
Placed in the middle
Q961
3.0/9.8
2.2/7.2
Placed in the middle
0.85m(2.8ft)
to door
Placed in the middle
3.5/11.5
3.1/10.2
Placed in the middle
1.17m(3.8ft)
to door
Placed in the middle
4.0/13.1
4.0/13.1
Placed in the middle
1.5m(4.9ft)
to door
Placed in the middle
Q962
4.0/13.1
2.8/9.2
Placed in the middle
1.05m(3.4ft)
to door
Placed in the middle
4.5/14.8
3.4/11.2
Placed in the middle
1.28m(4.2ft)
to door
Placed in the middle
5.0/16.4
4.0/13.1
Placed in the middle
1.5m(4.9ft)
to door
Placed in the middle
www.acti.com
INSTALLATION GUIDE
3
2.
Package Contents
Camera
Mounting Base
Quick Start Guide
Screw Kit
Quick Start
Guide
www.acti.com
INSTALLATION GUIDE
4
Part 2: Installation Steps
1. Installation
Please pay great attention to the mounting position. Inappropriate mounting
position may cause loss of accuracy. The recommended mounting position is
shown below:
Horizontal sketch map of mounting position
Effect picture after installation
Notice: Avoid the reflective environment (ex: Marble floor)
Vertical sketch map of mounting position
www.acti.com
INSTALLATION GUIDE
5
Make sure the camera is mounted vertically above the passenger flow
(90°vertical by the ground), see picture below:
Passenger flow
（
perpendicular to the door
）
For some scenarios where there are multiple cameras, mount the cameras
according to two rules.
Rule one: If there are turnstiles, each camera should be mounted to monitor
certain turnstile
www.acti.com
INSTALLATION GUIDE
6
Rule two:If there is no turnstile, at first, mount the cameras in one line, and
make sure the cameras have the same focal length. Then, keep a proper
distance between each camera according to the overlap (see the yellow
area below) of the adjacent two cameras’ counting width. The suggested
overlapping length is between 0.2-0.5m.
Sketch map of multiple cameras installation
Notice
:
1) People flow should be in vertical up-and-down direction
Passenger flow in horizontal direction (wrong)
www.acti.com
INSTALLATION GUIDE
7
Passenger flow in slant direction (wrong)
Passenger flow in vertical up-and-down direction (right)
2) Passageway width should be within camera’s counting width
3) Avoid obstacles such glass door, shield door and turnstile that block the
camera. For Each divided passageway, mount one camera right above.
www.acti.com
INSTALLATION GUIDE
8
4) The camera should be mounted as close as possible to the passageway
without obstacle. Remove the obstacle or adjust the camera mounting position if
there is obstacle below the camera. Meanwhile, to prevent miscounting, if there’s
a sliding door onsite, make sure the trajectory of the sliding door does not
overlap the detection line. Otherwise, the counting number may be misled by the
door opening and closing
Too far away from the door / Obstacle below camera
Recommended installation
www.acti.com
INSTALLATION GUIDE
9
2.
Configuration for single camera
Step 1: Enable People Counting: check [Configuration]-[People Counting]
-[Enable People Counting]
Step 2: Calibration- Select the green box, drag it to proper location and click
[Calibration]. After this, “Height” in the configuration page will refresh (close
to the real height). A red box, which means the counting scope, and yellow
detection line will turn up. The arrow shows the direction of entering. See
picture below:
Notice
:
If auto calibration fails, switch to [Manual] and input the measured “Height”,
then click [Calibration].
Step 3: Detection line: move the detection line to proper location, about 0.5m
to the door. Then adjust the length of detection line to the real door’s width by
dragging the detection line’s two ends. See picture below:
Notice:
You should make the whole detection line in the same ground level or it may
lose accuracy.
www.acti.com
INSTALLATION GUIDE
10
Step 4: Save configuration and test. After configuration, click [save] and test.
If miscounting happens, slightly adjust the detection line’s location and
length.
3. Configuration for multiple cameras
Step 1: Do configuration for each camera following the steps above
Step 2: Move each camera’s detection line and connect the ends of adjacent
lines. Some objects could be placed on the image border for reference. See
picture below:
Configuration of each detection line
Andere Handbücher für Q960
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere ACTi Sicherheitskamera Handbücher
ACTi
ACTi E12 Bedienungsanleitung
ACTi
ACTi E31 Bedienungsanleitung
ACTi
ACTi ACM-1511 Series Bedienungsanleitung
ACTi
ACTi ACM-7411 Series Gebrauchsanweisung
ACTi
ACTi CAM-6200 Bedienungsanleitung
ACTi
ACTi TCM-3011 Gebrauchsanweisung
ACTi
ACTi Z31 Bedienungsanleitung
ACTi
ACTi ACM-1230 Series Bedienungsanleitung
ACTi
ACTi Z94 Bedienungsanleitung
ACTi
ACTi E38 Bedienungsanleitung
ACTi
ACTi Z39 Bedienungsanleitung
ACTi
ACTi ACM-1100 Series Bedienungsanleitung
ACTi
ACTi A92 Bedienungsanleitung
ACTi
ACTi B21 Bedienungsanleitung
ACTi
ACTi CAM-6600 Series Gebrauchsanweisung
ACTi
ACTi TCM-6630 Bedienungsanleitung
ACTi
ACTi KCM-7211 Gebrauchsanweisung
ACTi
ACTi E99M Bedienungsanleitung
ACTi
ACTi I98 Bedienungsanleitung
ACTi
ACTi D71 Bedienungsanleitung
