ADTRAN IQ 710 Benutzerhandbuch

IQ 710

System Manual

Part Number 1202800L1

1202800L1 IQ 710 Base Unit

1202802L1 T1/FT1 Network Interface Module

1202803L1 T1/FT1+DSX-1 Network Interface Module

1204002L3 V.34 DBU Module

1204004L2 ISDN BRI DBU Module

1204008L2 ISDN PRI DBU Module

1204006L2 DCE DBU Module

4202801L1 IQ 710 with 56k/64k Network Interface Module

4202802L1 IQ 710 with T1/FT1 Network Interface Module

4202803L1 IQ 710 with T1/FT1 + DSX-1 Network Interface Module

4202811L1 IQ 710 with 56k/64k Network Interface Module and Traffic Shaping

4202812L1 IQ 710 with T1/FT1 Network Interface Module and Traffic Shaping

4202813L1 IQ 710 with T1/FT1 + DSX-1 Network Interface Module and Traffic Shaping

61202800L1-1B

April 2002

Trademarks

Any brand names and product names included in this manual are trademarks, registered

trademarks, or trade names of their respective holders.

To the Holder of the Manual

The contents of this manual are current as of the date of publication. ADTRAN reserves

the right to change the contents without prior notice.

In no event will ADTRAN be liable for any special, incidental, or consequential damages

or for commercial losses even if ADTRAN has been advised thereof as a result of issue of

this publication.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

Printed in U.S.A.

About this Manual

This manual provides a complete description of the IQ 710 system and system software.

The purpose of this manual is to provide the technician, system administrator, and

manager with general and specific information related to the planning, installation,

operation, and maintenance of the IQ 710. This manual is arranged so that needed

information can be quickly and easily found. The following is an overview of the contents.

Section 1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page - 15

Provides managers with an overview of the IQ 710 system.

Section 2 Engineering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . page - 19

Provides information to assist network designers with incorporating the IQ 710 system

into their networks.

Section 3 Network Turnup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . page - 31

Provides step-by-step instructions on how to install the IQ 710 unit, determine the

parameters for the system, install the network and option modules, and power up the

system.

Section 4 User Interface Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page - 37

Explains the VT-100 and Telnet interfaces, the VT-100 user interface conventions and the

IQ 710 top-level menu tree.

Section 5 Detail Level Procedures (DLP) . . . . . . . . . . . . . . . . . . . . . . page - 81

Provides the Detail Level Procedures for how to perform various unit functions

(upgrading firmware, telnet, etc.).

Section 6 Configuration Guides (CFG) . . . . . . . . . . . . . . . . . . . . . . . . page - 145

Provides step-by-step instructions for configuring some of the most common IQ 710

applications.

Section 7 N-Formant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page - 295

Describes how to navigate the N-Formant management system.

Revision History

This is the 2nd issue of this manual. This revision adds the traffic shaping feature.

Safety Instructions

When using your telephone equipment, please follow these basic safety precautions to

reduce the risk of fire, electrical shock, or personal injury:

1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laun-

dry tub, in a wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There

is a remote risk of shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do

not dispose of batteries in a fire. They may explode. Check with local codes for spe-

cial disposal instructions.

Save These Important Safety Instructions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the equipment or

endangerment to human life.

FCC regulations require that the following information be provided in this manual:

1. This equipment complies with Part 68 of FCC rules. On the bottom of the equipment housing is a label

showing the FCC registration number and ringer equivalence number (REN). If requested, provide this

information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone company may temporarily dis-

continue service. If possible, advance notification is given; otherwise, notification is given as soon as

possible. The telephone company will advise the customer of the right to file a complaint with the

FCC.

3. The telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect the proper operation of this equipment. Advance notification and the opportunity to main-

tain uninterrupted service are given.

4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty infor-

mation. The telephone company may require this equipment to be disconnected from the network until

the problem is corrected or it is certain the equipment is not malfunctioning.

5. This unit contains no user-serviceable parts. In the event of equipment malfunction, all repairs should

be performed by ADTRAN. It is the responsibility of users requiring service to report the need for ser-

vice to their distributor or ADTRAN. See Customer Service, Product Support Information, and Train-

ing in this front matter for information on contacting ADTRAN for service

6. An FCC compliant telephone cord with a modular plug is provided with this equipment. This equip-

ment is designed to be connected to the telephone network or premises wiring using an FCC compati-

ble modular jack, which is Part 68 compliant.

7. The following information may be required when applying to the local telephone company for leased

line facilities:

8. The REN is useful in determining the quantity of devices you may connect to your telephone line and

still have all of those devices ring when your number is called. In most areas, the sum of the RENs of

all devices should not exceed five. To be certain of the number of devices you may connect to your

line as determined by the REN, call your telephone company to determine the maximum REN for your

calling area.

9. This equipment may not be used on coin service provided by the telephone company. Connection to

party lines is subject to state tariffs. Contact your state public utility commission or corporation com-

mission for information.

Part Number Reg. Number Service Type REN/SOC FIC USOC

1202801L1 HDCUSA-44573-DE-N

56 kbps Digital Interface

64 kbps Digital Interface 6.0F

04DU5-56

04DU5-64 RJ-48S

1202802L1

HDCUSA-44574-DE-N

1.544 Mbps-SF

1.544 Mbps-SF and B8ZS

1.544 Mbps-ESF

1.544 Mbps-ESF and B8ZS

6.0F

04DU9-BN

04DU9-DN

04DU9-1KN

04DU9-1SN

RJ-48C

1202803L1

1202805L1 US: HDCDENAN1200805L1

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital terminal equipment

without encoded analog content and billing protection is used to transmit digital signals containing

encoded analog content which are intended for eventual conversion into voiceband analog signals and

transmitted on the network.

• The affidavit shall affirm that either no encoded analog content or billing information is being trans-

mitted or that the output of the device meets Part 68 encoded analog content or billing protection spec-

ifications.

• End user/customer will be responsible for filing an affidavit with the local exchange carrier when con-

necting unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.

• Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit

requirement for subrate services is waived.

Affidavit for Connection of Customer Premises Equipment

to 1.544 Mbps and/or Subrate Digital Services

For the work to be performed in the certified territory of ___________________(telco name)

State of ________________

County of ________________

I, _______________________ (name), _____________________________(business address),

____________________ (telephone number) being duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544

Mbps and/or ________ subrate digital services. The terminal equipment to be connected complies with

Part 68 of the FCC rules except for the encoded analog content and billing protection specifications. With

respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital

CPE with respect to analog content and encoded billing protection information continuously complies

with Part 68 of the FCC Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded analog content or billing informa-

tion which is intended to be decoded within the telecommunications network.

( ) The encoded analog content and billing protection is factory set and is not under the control of the cus-

tomer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance,

and adjustment of the encoded analog content and billing information has (have) been trained to perform

these functions by successfully having completed one of the following (check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the equipment used to encode analog

signals; or

( ) B. A training course provided by the customer or authorized representative, using training materials

and instructions provided by the manufacturer/grantee of the equipment used to encode analog sig-

nals; or

( ) C. An independent training course (e.g., trade school or technical institution) recognized by the man-

ufacturer/grantee of the equipment used to encode analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the con-

trol of a supervisor trained in accordance with _________ (circle one) above.

I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate

compliance with the information as provided in the preceding paragraph, if so requested.

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of _______________, _______

_________________________________

Notary Public

My commission expires:

_________________________________

Industry Canada Compliance Information

Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the

“IC:” in front of the certification/registration number) signifies that the Industry Canada technical

specifications were met.

Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the

documentation or on the product labeling/markings. The REN assigned to each terminal device indicates

the maximum number of terminals that can be connected to a telephone interface. The termination on an

interface may consist of any combination of devices subject only to the requirement that the sum of the

RENs of all the devices should not exceed five (5).

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus

as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the

Department of Communications.

Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques

de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee

par le ministre des Communications.

Andere Handbücher für IQ 710

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Hardware Handbücher

ADTRAN

ADTRAN U-BR1TE Bedienungsanleitung

ADTRAN

ADTRAN Total Access 300 Series Bedienungsanleitung

ADTRAN

ADTRAN TA 900 Bedienungsanleitung

ADTRAN

ADTRAN SHDSL NxNTU Bedienungsanleitung

ADTRAN

ADTRAN Total Access DSLAM 16-Port ADSL2+ Access Module... Bedienungsanleitung

ADTRAN

ADTRAN Stub Routing Bedienungsanleitung

ADTRAN

ADTRAN MX2800 STS-1 Benutzerhandbuch

ADTRAN

ADTRAN ISU 512E Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1335 Series Bedienungsanleitung

ADTRAN

ADTRAN 1200221L1 Bedienungsanleitung

ADTRAN

ADTRAN SHDSL T1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1224 Bedienungsanleitung

ADTRAN

ADTRAN Express 3000 Bedienungsanleitung

ADTRAN

ADTRAN jobAid Total Access 838 Bedienungsanleitung

ADTRAN

ADTRAN XFP NG-PON2 ONU Bedienungsanleitung

ADTRAN

ADTRAN SDX 611 GPON SFU ONT Bedienungsanleitung

ADTRAN

ADTRAN 3.125 Gigabit Ethernet Bedienungsanleitung

ADTRAN

ADTRAN NetVanta E1/FE1 + G.703 Network Interface... Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 900 Series Handbuch

ADTRAN

ADTRAN XFP Bedienungsanleitung

ADTRAN

ADTRAN 1200630L1 Bedienungsanleitung

ADTRAN

ADTRAN TSU LT Bedienungsanleitung

ADTRAN

ADTRAN 1200 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 4660 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung