Advantech ECU-P1702 Installations- und Betriebshandbuch

STARTUP MANUAL

ECU-P1702 Startup Manual 1

ECU-P1702

10MS/s 12-bit Simultaneous 4-ch Analog Input PCI-104 Card

Packing List

Before you begin installing your module, please make

sure that the following materials have been shipped:

ECU-P1702 card

Energy Series Driver and Utility DISC

Quick Start User Manual

1 x front Panel (for ECU-P1702)

1 x 5 pin plug-in-blocks

6 x M3 bolts

1x ROHS LIST

1 x warranty card

If any of these items are missing/damaged, contact

your distributor or sales representative immediately.

Notes

For more information on this and other Advantech

products, please visit our websites at:

http://www.advantech.com

http://www.advantech.com/eAutomation

For technical support and service:

http://www.advantech.com.tw/eservice

This manual is for ECU-P1702.

Part No: 2003170200 1st Edition

December 2013

User Manual

For more detailed information on this product, please

refer to the ECU-P1702 User Manual on the CD-ROM

(PDF format). CD:\ ECU-P Cards\ECU-P1702\User's

Manual.

Declaration of Conformity

FCC Class A

This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to part 15 ofthe FCC Rules. These limits

are designed to provide reason-able protection

against harmful interference when theequipment

is operated in a commercial environment. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with theinstruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause interference in which case the user is

required to correct interference at his own expense.

This product has passed the CE test for environmental

spec-ifications when shielded cables are used

for external wiring.We recommend the use of

shielded cables. This kind of cable is available from

Advantech. Please contact your local representative.

Overview

The ECU-P1702 is an advanced high-performance

multifunction card based on the universal PCI-104

bus. The maximum sampling rate of ECU-P1702 is

up to 10MS/s with 4 A/D converters simultaneous

sampling on each channel, with a large FIFO of

32K sample.

2 ECU-P1702 Startup Manual

Connectors

Connector Description

Figure 1 -Connectors on ECU-P1702

Table 1 - Connector Description

Connector Function

CN1 Analog input CH-0

CN4 Analog input CH-1

CN6 Analog input CH-2

CN8 Analog input CH-3

CN11 Digital input/output

CN15 Ext. Trigger & CLK

SW1 Slot select for PCI BUS

SW2 Borad ID

SW3 ~ SW6 AI Input Impedance

Instant AI & Buffered AI Connection

Figure 2 -Instan AI & Buffered AI Connection

Speciﬁcations

General

Power Consumption: 5 V @ 700 mA (max.),

3.3 V @ 850 mA (max.)

Bus Type: PCI-104

I/O Connector: 4 BNC connector for AI,

1 plug-in terminal block connector for ext. clock

and trigger

Operating Temperature: -20 ~ 70°C (-4 ~

158°F) @ 5 ~ 85% RH

Storage Temperature: -40 ~ 80°C (-40 ~176°F)

Storage Humidity: 5 ~ 95% RH, non-

condensing (IEC 60068-2-3)

Certication: CE/ FCC

Analog Input

Channels: 4 Single- ended

Resolution: 12 bits

Max. Sampling Rate: 10 MS/s

FIFO Size: 32 K samples

Overvoltage Protection: ±14 V

Input Impedance: 50 ohm/1M ohm/Hi Z switch

selectable

Sampling Mode: Software, onboard

programmable pacer and external (TTL Level)

Trigger Mode: Delay To Start Trigger, Delay To

Stop Trigger

Trigger Source: Analog Trigger, External

Trigger

Input Range: ±5 V, ±2.5 V, ±1 V, ±0.5 V

Digital Input

Channels: 32 (Setting DIO in the same direction)

Compatibility: 5 V/ TTL

Input Voltage:

–Logic0: 0.8 V max.

–Logic1: 2 V min.

Digital Output

Channels: 32 (Setting DIO in the same direction)

Compatibility: 5 V/ TTL

Output Voltage:

–Logic0: 0.4 V max.

–Logic1: 2.4 V min.

ECU-P1702 Startup Manual 3

AI Trigger & CLK Source (CN15)

The ECU-P1702 introduces a double-clock system,

with SCAN clock and CONV clock, to generate

efcient A/D conversion clocks at dedicated timing.

A/D conversion clocks come from internal clock

sources or external signals on connector. The CLK

has several sources.

Internal A/D clock derived from 32-bit divider

External A/D clock from terminal board

With ECU-P1702, user can dene the type of trigger

source as rising-edge or falling-edge. The Trigger has

several sources.

External digital (TTL) trigger from terminal

board

Soft trigger

Analog threshold trigger

Table 2 - PIN Definition for CN15

PIN Signal Description

1 GND GND

2 CLK1 Ext. Scan CLK

3 TRG1 Ext. Trigger 1

4 CLK0 Ext. Convert CLK

5 TRG0 Ext. Trigger 0

Tip: TRG1 is not available.

Figure 3 -Trigger Source & CLK Source Connection

Digital Input Connection (CN11)

Figure 4 -Digital Input Connection

Digital Output Connection (CN11)

Figure 5 -Digital Output Channel Connection

Setting the BoardID Switch (SW2)

The ECU-1702 has a built-in DIP switch (SW2),

which is used to dene each card's board ID. You can

determine the board ID on the register as shown in

Table 3. When there are multiple cards on the same

chassis, this board ID setting function is useful for

identifying each card's device number through board

ID. We set the ECU-P1702 board ID as 0 at the factory.

If you need to adjust it to other board ID, set the SW2

by referring to DIP switch setting.

ECU-P1702 Startup Manual 4

Installation

Hardware Installation

1. Turn the PC’s power off. Turn off the power

of any peripheral devices such as printers and

monitors.

2. Disconnect the power cord and any other cables

from the back of the computer.

3. Remove the system unit cover (see the user’s

guide for your chassis if necessary).

4. Remove the CPU card from the chassis (if

necessary) to gain access to the card’s PCI-104

connector.

5. The ECU-P1702 card to the PCI-104 connector.

Carefully align the pins with the PCI-104

connector. Slide the module into the connector.

The module pins may not slide all the way into

the connector; do not force the pins into place, or

the module may be damaged.

6. Fasten the module to the CPU card by using the

included brass screw. Screw the brass spacer

into the threaded hole on the CPU card. Do not

tighten too much, or the threads may be damaged.

7. Reinstall the CPU card and replace the system

unit cover. Reconnect the cables you removed in

step 2.

8. Attach the 5 PIN terminal accessory to the

ECU-P1702.

9. Plug in and turn on the power. This completes the

hardware installation. Install the software driver

as described in the following section.

Table 3 - Board ID Settings

SW2 3 2 1 0

BoardID ID3 ID2 ID1 ID0

0* ON ON ON ON

1 ON ON ON OFF

2 ON ON OFF ON

3 ON ON OFF OFF

4 ON OFF ON ON

5 ON OFF ON OFF

6 ON OFF OFF ON

7 ON OFF OFF OFF

8 OFF ON ON ON

9 OFF ON ON OFF

10 OFF ON OFF ON

11 OFF ON OFF OFF

12 OFF OFF ON ON

13 OFF OFF ON OFF

14 OFF OFF OFF ON

15 OFF OFF OFF OFF

Slot Select for PCI BUS (SW1)

The ECU-P1702 has a built-in DIP switch (SW1),

which is used to dene each card's interrupt number.

You can determine the INT ID as shown in Table 4.

When there are multiple cards on the same chassis,

this INT ID setting function is useful for each card.

We set the ECU-P1702 INT ID as 0 at the factory. If

you need to adjust it to other INT ID, set the SW1 by

referring to DIP switch setting.

Table 4 - Slot Selection for PCI BUS

Posi-

tion1

Posi-

tion2

Switch

Value

Module

Slot

REQ# GNT# CLK INT0#

ON ON 0 0 REQ0# GNT0# CLK0 INTA#

ON OFF 1 1 REQ1# GNT1# CLK1 INTB#

OFF ON 2 2 REQ2# GNT2# CLK2 INTC#

OFF OFF 3 3 REQ3# GNT3# CLK2 INTD#

Tip: If Position1 and Position2 on SW1 both setting

as OFF, the ECU-P1702 card could not be detected.

Input Impedance Select(SW3~SW6)

The ECU-P1702 has four built-in DIP switch

(SW3~SW6), which are used to select different input

impedance for each AI channel. You can determine

the impedance value as shown in Table 5. Wet set the

ECU-P1702 impedance as Hi Z at the factory. If you

need to adjust it to other impedance, set the SW3~SW6

by referring to DIP switch setting.

Table 5 - AI Input Impedance Settings

Switch Value Impedance Value

00 Hi Z

01 1 M Ohm

10 50 Ohm

11 ERROR

ECU-P1702 Startup Manual 5

Exploded Diagram

This is ECU-P1702 mounted to the blasting

ECU-1871 system diagram, convenient for customers

to understand the installation mode of the card.

Figure 8 -ECU-P1702 Exploded Diagram

Software Installation

1. Insert the companion DVD into your DVD

disc. The setup program will be launched

automatically if you have the auto play function

enabled on your system. Then the setup program

will be launched.

2. Push the "CONTINUE" button to next step.

3. Select the "Installation" option.

4. Select the "DAQNavi SDK" option to install

DAQNavi SDK Package.

5. After DAQNavi SDK has been installed

successfully, Advantech Navigator will

be lunched automatically. Of course,

you can open the Advantech Navigator

from "Start>>All Programs>>Advantech

Automation>>DAQNavi>>Adventech

Navigator" manually. For win7 user, you must

run it by right click the item and select the 'Run

As Administrator' item from the popup menu.

6. Click "+" on the left of node named "Supported

Devices" to expand the contents, then all the

supported devices will be listed under this node.

7. Choose the device which you want to install

driver, right click on the node, there will be a

popup dialog shown, click "Install Driver" on the

dialog, thus, the driver will start to install.

Figure 6 -Install Driver for ECU-P1702

8. Click "OK" to nish installation. Navigator

detects and installs ECU-P1702 device on

the system automatically, then you can nd

"ECU-P1702" device node under "Installed

Devices" node.

Figure 7 -Device Setting for ECU-P1702

For more detailed Software Installation information on

this product, please refer to the ECU-P1702 Manual

on the CD-ROM (PDF format). CD: \ ECU-P Cards\

ECU-P1702\User's Manual.

ECU-P1702 Startup Manual 6

Block Diagram

Figure 9 -ECU-P1702 Block Diagram

Dimension Diagram

Figure 10 -ECU-P1702 Dimension Diagram

Inhaltsverzeichnis

Andere Advantech E/A-System Handbücher

Advantech

Advantech PCI-1758UDO Installations- und Betriebshandbuch

Advantech

Advantech PCI-1750 Bedienungsanleitung

Advantech

Advantech WISE-2200-M Installations- und Betriebshandbuch

Advantech

Advantech B+B SmartWorx Zlinx ZZ24D-NA-SR Bedienungsanleitung

Advantech

Advantech WISE-4610 Series Bedienungsanleitung

Advantech

Advantech ADAM-6100EI Series Bedienungsanleitung

Advantech

Advantech AIIS-E730 Installations- und Betriebshandbuch

Advantech

Advantech PCM-3730 Bedienungsanleitung

Advantech

Advantech APAX-5000 Series Bedienungsanleitung

Advantech

Advantech ADAM-3600-A1F Bedienungsanleitung

Advantech

Advantech ADAM-6156PN Bedienungsanleitung

Advantech

Advantech UNO-2000-LKAE Bedienungsanleitung

Advantech

Advantech PCIE-1730 Series Bedienungsanleitung

Advantech

Advantech WISE-4050 Bedienungsanleitung

Advantech

Advantech AMAX-5000 Series Bedienungsanleitung

Advantech

Advantech WISE-4210 Series Bedienungsanleitung

Advantech

Advantech ADAM-6000 series Bedienungsanleitung

Advantech

Advantech PCL-733 Bedienungsanleitung

Advantech

Advantech USB-5817 Installations- und Betriebshandbuch

Advantech

Advantech WISE-4671 Bedienungsanleitung

Advantech

Advantech ADAM-5000/TCP Series Bedienungsanleitung

Advantech

Advantech USB-4716 Bedienungsanleitung

Advantech

Advantech PCIE-1756H Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung