Aeotec AEO ZWA008-C Bedienungsanleitung

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 1/10

Door / Windows Sensor 7 user guide

Modiﬁed on: Mon, 15 Jul, 2019 at 12:56 AM

AeotecDoor/WindowSensor7.

AeotecDoor/WindowSensor7hasbeencraftedtopowerconnectedlightingusingZ-WavePlus(http://aeotec.com/z-

wave-plus).ItispoweredbyAeotec’sGen5(http://aeotec.com/z-wave-gen5)technologyandS2framework.Youcanfindout

moreaboutDoor/WindowSensor7(https://aeotec.com/z-wave-door-window-sensor)byfollowingthatlink.

ToseewhetherDoor/WindowSensor7isknowntobecompatiblewithyourZ-Wavesystemornot,pleasereferenceour

Z-Wavegatewaycomparison(http://aeotec.com/z-wave-gateways)listing.ThetechnicalspecificationsofDoor/

WindowSensor(https://aeotec.freshdesk.com/a/solutions/articles/6000218908-door-window-sensor-7-technical-

specifications-)7canbeviewedatthatlink.

FamiliarizeyourselfwithyourDoor/WindowSensor7.

Packagecontents:

1. SensorUnit.

2. Cover

3. BigMagnet.

4. SmallMagnet.

5. Double-SidedTapelarge(×2).

6. Double-SidedTapesmall(x2).

7. Screws(×4).

8. Dowels(x4).

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 2/10

Importantsafetyinformation.

Pleasereadthisandotherdeviceguidescarefully.FailuretofollowtherecommendationssetforthbyAeotecLimited

maybedangerousorcauseaviolationofthelaw.Themanufacturer,importer,distributor,and/orresellerwillnotbe

heldresponsibleforanylossordamageresultingfromnotfollowinganyinstructionsinthisguideorinothermaterials.

Keepproductandbatteriesawayfromopenflamesandextremeheat.Avoiddirectsunlightorheatexposure.Always

removeallbatteriesfromproductsthatarebeingstoredandnotused.Batteriesmaydamagetheapplianceiftheyleak.

Donotuserechargeablebatteries.Ensurecorrectpolaritywheninsertingthebatteries.Improperbatteryusemay

damagetheproduct.

Door/WindowSensor7isintendedforindooruseindrylocationsonly.Donotuseindamp,moist,and/orwet

locations.

Itcontainssmallparts;keepawayfromchildren.

QuickStart

Pre-InstallationofDoor/WindowSensor7.

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 3/10

Openthecoverbypressingthecliponthesideandpullingthecoverupwards.

Insertafresh1*1/2AAbattery,butpayattentiontothepolarity

InstallyourDoor/WindowSensor7.

Thesensorcanbemountedeitheronthemovingpartoronthefixedpartofadoororawindow.Mountingcanbe

accomplishedeitherusingthetapebypeelingofftheprotectionfoilorusingtwoscrewswiththeholesinsidethebattery

compartment.Ifthetiltdetectiononawindow(onlynormalwindows,noroofwindows)shallbeusedthesensordevice

mustbeplacedonthemovingpartofthewindowandthemagnetonthewindowframe.Thesensorcomeswithtwotypes

ofmagnets:

Thestandardmagnetcoveredbyplasticpart,mountablebesidethesensor.Makesurethetwoindicatinglineson

sensorenclosureandmagnetareoppositetoeachother.Theimageontheright-hand-sideshowsthepositionof

magnetandsensorbody.

Aslim"naked"magnettobemountedbehindthesensorincasethesensorbodyisplacedonthesideofawindow.

Tousethetiltingfunction,theopeningangleofthewindowmustbeatleast5°orgreater.

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 4/10

ForGermanstylewindowstherethewindowsitsontopofthewindowframemountingonthesideofthewindowishighly

recommended.Ifnotiltingdetectionisused,thesensorcanbeplacedonanypositionofthedoororthewindow.Incase

tiltingdetectionisdesiredthesensorshouldbeplacedontheuppersideofthewindow.

Installationoftheflatmagnet

Wheninstallingtheflatmagnetinahiddenlocation,makesurethatitisonthelongersideasseenfromthemarkonthe

Door/WindowsSensor7.

AddingyourDoor/WindowsSensor7toZ-Wavenetwork.

1. SetyourZ-Wavecontrollerintopairingmode.

2. Triple-clickthetamperswitchonDoor/WindowSensor7-thisbeginstoblinkfivetimes

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 5/10

3. Aftercompletionoftheinclusion,itlightsuponcebeforeitgoesout.

4. Closethecover

FunctionsofDoor/WindowSensor7.

Open/Close

Onceinstalledthesensorwillreport"open"and"close"statuschangestoacentralZ-Wavecontrollerusingnotification

commands.

Tiltdetection

Thetiltdetectionallowsreportingthewayawindowisopened.Thisisaccomplishedusingthecommandclass"binary

sensor-tilt-type".Incasethewindowisclosedoropenedwithouttiltingthetiltsensorwillreport"Off".Incasethe

windowistiltedan"On"isreported.Theangleofinclinationofthewindowmustbeatleast5°.

Advancesfunctions.

ScrewTerminal.

Withparameter#1youcanchoosebetweentheinternalmagnetortheexternalconnectionssuchaspushbuttonsordry

contactsensors.



#1:Notused.

#2:Notused.

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 6/10

#3:DigitalInput

#4:Ground

Digital+Groundisusedtoconnectanexternaldrycontactmechanismtocontrolscenes.

Pushbutton

Watersensorprobes

Externalmagnetdetection

etc.

Note:PleasenotethatthecontactDigitalInput(#3)andGround(#4)isanormallyopen(NO)contact.Closingthe

contactsendsoutacommand(OpenorClose).YoumustuseaNOdrycontactdevicewiththeseterminals.

Door/WindowSensor7asDryContactSensor.

Using conﬁguration commands the source of "open" and "close" events can be chosen between the internal magnet

detector or external dry contact connected on terminal #3 and #4.

You can ﬁnd direct information in this article here:

https://aeotec.freshdesk.com/support/solutions/articles/6000223859

(https://aeotec.freshdesk.com/support/solutions/articles/6000223859)

SceneController.

Whenactivatedbyconfigurationparameter#13thedevicecanperformasascenecontroller.Theexternaldrycontact

willthenactasascenecontrollerwithatotalof7scenesthatcanbeactivated:

1. ContactPressed1time

2. ContactPressed2time

3. ContactPressed3time

4. ContactPressed4time

5. ContactPressed5time

6. Contacthelddown

7. Contactreleased

YoucanfindoutmoreinformationonhowtouseDoor/WindowSensor7inthisarticlehere:

https://aeotec.freshdesk.com/support/solutions/articles/6000223885

(https://aeotec.freshdesk.com/support/solutions/articles/6000223885)

Communicationtest.

This utilizes the Power Level command class to determine the health between the Door / Window Sensor 7 and your

Z-Wave gateway. This will tell you if the Door / Window Sensor 7 has a healthy connection to your system and is a

great method of debugging connectivity issues.

1. Set Parameter #4 to value #1

2. Doubleclick the Tamper Switch.

3. Result:

Blinksonce- success

Blinks5xtimes- failure

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 7/10

Firmware-UpdateovertheAir.

Thisdeviceiscapableofreceivinganewfirmware'overtheair'.Theupdatefunctionneedstobesupportedbythe

centralcontroller.Oncethecontrollerstartstheupdateprocess,performthefollowingactiontoconfirmthefirmware

update:

1. WakeUpthedevicebyremovingthecover.

2. Thehitthetamperswitchonce.

Sendawakeupnotification.

InordertosendyoursensorsnewconfigurationcommandsfromyourZ-Wavecontrollerorgateway,itwillneedtobe

wokenup.

1. WakeUpthedevicebyremovingthecover.

2. Thehitthetamperswitchonce.

Note:Door/WindowSensor7remainsawakeuntilthehousingisclosedagain.

RemoveyourDoor/WindowSensor7fromZ-Wavenetwork.

YoursensorcanberemovedfromyourZ-Wavenetworkatanytime.You'llneedtouseyourZ-Wavenetwork'smain

controller/gateway.Todothis,pleaserefertothepartofyourgatewaysrespectivemanualthattellsyouhowtoremove

devicesfromyournetwork.

1. SetyourZ-Wavecontrollerintounpairmode.

2. Triple-clickthetamperswitchonDoor/WindowSensor7within1.5seconds-thiswillcausetheLEDtoblink

fivetimes.

3. Afterasuccessfulexclusion,itwilllightupitsLEDfor2secondsthendeactivate.

ResetyourDoor/WindowsSensor7.

ThisdevicealsoallowsbeingresetwithoutanyinvolvementofaZ-Wavecontroller.Thisprocedureshouldonlybeused

whentheprimarycontrollerisinoperable.

Tomanuallyfactoryreset:

1. RemovethecoverofDoor/WindowSensor7

2. Pressandholdtamperswitchfor5secondsuntiltheredLEDblinks.

3. Releasethetamperswitch

4. Immediatelypressandholdthetamperswitchfor5secondsuntiltheredLEDblinks.

ParameterConfigurations.

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 8/10

Parameter1:OperationMode.

Thisparameterallowsswitchingbetweeninternalsensorandexternalsensor.

Size:1Byte,DefaultValue:0

Setting Description

0theinternalhallsensorisenabled

(externalinputdisabled)

1theexternalinputisenabled(internal

hallsensordisabled)

Parameter2:Door/WindowState.

ThisparameterallowssettingDoor/WindowSensor7statewhenthemagnetisclosetothesensor.

Size:1Byte,DefaultValue:0

Setting Description

0 closedwhenthemagnetisnear

1 openedwhenthemagnetisnear

Parameter3:VisualLEDIndications.

ThisparameterdefineseventsindicatedbythevisualLEDindicator.Disablingeventsmightextendbatterylife.

Size:1Byte,DefaultValue:7,Range:0-7

Setting Description

0 noindications

1indicationofopening/closingstatus

change

2indicationofwakeup(1xclickor

periodical)

4 indicationofdevicetampering

Parameter4:Rangetestafterdoubleclick.

AllowsenablingtheactivationofZ-WaverangetestwithdoubleclickofaTamperSwitch2.

Size:1Byte,DefaultValue:0

Setting Description

0 Disable

1 Enable

Parameter5:Group2AssociationTriggers.

ThisparameterdefineseventsthatresultinsendingOn/Offcommandstodevicesaddedtothe2ndAssociationGroup.

ThesecommandsaresentalternatelytoswitchthedevicesOnandOff.CommandsrepresentthevaluesofBASIC

SETcommandframes.Thisparameterisinactiveinexternaldry-contactmode(parameter“OperationMode”setto1).

Size:1Byte,DefaultValue:0

Setting Description

0 switchafteropeningandclosing

1 switchafteropening

2 switchafterclosing

Parameter6:CommandssenttoassociateddevicesonGroup2.

Commandframessenttodevicesaddedtothe2ndassociationgroup.

Size:1Byte,DefaultValue:2

Setting Description

0 On

1 Off

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 9/10

2 OnandOff

Parameter7:ValuesofONcommandframesenttoGroup2Association.

Thevalueof0turnsOFFthedevice,255turnsitOn.InthecaseofassociatingtheDimmerorRollerShuttermodule,

values

Size:1Byte,DefaultValue:255

Setting Description

0-99 allowsettinganAssociateddevicetoa

specifiedlevel(0isOFF)

255 ON

Parameter8:ValueofOFFcommandframesenttoGroup2Association.

810-99,2550ValueofOFFcommandframesentto2ndAssociationGroup

Thevalueof0turnsOFFthedevice,255turnsitOn.InthecaseofassociatingtheDimmerorRollerShuttermodule,

values.

Size:1Byte,DefaultValue:0

Setting Description

0-99 allowsettinganassociateddevicetoa

specifiedlevel.(0isOFF)

255 ON

Parameter9:TimeDelayofONcommandfromGroup#2.

ThetimeperiodafterwhichOncommandframewillbesent.

Size:1Byte,DefaultValue:0

Setting Description

0-

32400 Timesetinseconds

Parameter10:TimeDelayofOFFcommandfromGroup#2.

ThetimeperiodafterwhichtheOFFcommandframewillbesent.

Size:1Byte,DefaultValue:0

Setting Description

0-

32400 Timeinseconds

Parameter11:Delayoftamperalarmcancellation.

Thetimeperiodafterwhichatamperalarmwillbecanceled.

Size:1Byte,DefaultValue:0

Setting Description

0-

32400 Timeinseconds

Parameter12:Reportingtamperalarmcancellation.

Reportingcancellationoftamperalarmtothecontrollerand3rdAssociationGroup.

Size:1Byte,DefaultValue:1

Setting Description

0 donotsendtampercancellationreport

1 sendtampercancellationreport

Parameter13:CentralSceneEventfunctionality.

Enable/DisableCentralSceneEvents.

Size:1Byte,DefaultValue:0

31/07/2019 Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide 10/10

Setting Description

0 ContactSceneEventsdisabled

1 ContactSceneEventsenabled

Parameter14:TiltSensorFunctionalityenable/disable.

TiltSensorfunctionalityenable/disable.

Size:1Byte,DefaultValue:1

Setting Description

0 TiltSensordisabled

1 TiltSensorEnabled

Parameter15:TiltsensitivityfromV1.02andhigher

Youcanusethisparametertoadjustthetiltsensitivityifthetiltistoolowortoohigh.

Size:1Byte,DefaultValue:50

Setting Description

1-100 Tiltsensitivity

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Aeotec Zubehör Handbücher

Aeotec

Aeotec Recessed Door Sensor 7 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Door / Window Sensor 7 Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec ZWA005 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Siren 6 Bedienungsanleitung

Aeotec

Aeotec Doorbell Gen5 Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Z-Wave Multisensor DSB05-ZWEU Bedienungsanleitung

Aeotec

Aeotec DSB05106-ZWUS Bedienungsanleitung

Aeotec

Aeotec ZW162 Bedienungsanleitung

Aeotec

Aeotec Door / Window Sensor 7 Bedienungsanleitung

Aeotec

Aeotec ZW089 Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec AEOEZW120 Bedienungsanleitung

Aeotec

Aeotec GP-AEOWLSEU Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec MultiSensor Bedienungsanleitung

Aeotec

Aeotec ZW187 Bedienungsanleitung

Aeotec

Aeotec Button Bedienungsanleitung

Aeotec

Aeotec AEOEZWA009 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung