Aeotec ZWA005 Bedienungsanleitung

TriSensor

ZWA005

Used in this guide.

Important safety information.

Please read this and the electronic guide(s) at http://support.aeotec.com/trisensor carefully. The failure

to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of

the law. The manufacturer, importer, distributor, and / or reseller will not be held responsible for any

loss or damage resulting from not following any instructions in this guide or in other materials.

TriSensor is intended for use in dry locations only. Do not use in damp, moist, and / or wet locations.

Contains small parts; keep away from children.

Quick start.

The following will step you through installing TriSensor and connecting it to your Z-Wave network.

1. Select an installation location for TriSensor. The sensor uses light and heat readings to detect

motion, so avoid pointing it at sources of both. Tips on optimising the installation location of

TriSensor can be found online in its digital guide.

2. Remove the backplate from TriSensor.

3. Insert one CR123A batteries with the correct orientation.

4. Replace the backplate.

5. Set your Z-Wave gateway into its ‘add device’ mode in order to connect TriSensor to your Z-

Wave system. Refer to the gateway’s manual if you are unsure of how to perform this step.

6. inclusion in network:

Press once TriSensor’s Action Button,If it is the first installation., the yellow LED will keep

solid until whole network processing is complete. If successful, the LED will flash white -> green ->

white -> green ,After 2 seconds have finished.If fail, the yellow LED lasts for 30 seconds, then the

green LED flashes once.

If it is the S2 encryption network, please enter the first 5 digits of DSK, and the location of

DSK is shown in the figure1.

7. exclusion out network:

Press once TriSensor’s Action Button, the Purple LED will keep solid until whole network

processing is complete.if the exclusion is successful, the LED will flash white -> green ->white ->

green and then LED will pulse a blue.If fail, the yellow LED lasts for 30 seconds, then the

greenLED flashes once.

figure1

8. TriSensor can be installed on a flat surface such as a shelf, in a corner or on a wall using the

Back-Mount Arm, or within a ceiling or wall using its Recessor accessory (sold separately). If

using the Back-Mount Arm;

a. Screw Back-Mount Arm into the corresponding threaded hole on the back of TriSensor.

b. Affix Back-Mount Arm to your desired location using the provided double-sided tape or

KA2.5×20 mm screws.

c. Angle the TriSensor as desired.

Get help & learn more.

Should you encounter any problem with TriSensor, visit http://support.aeotec.com/trisensor or contact

our support team via aeotec.com/contact. You can also learn more about TriSensor features,

configuration options, and technical specifications at the link.

Gateway compatibility.

To see if this device is known to be compatible with your Z-Wave gateway, please refer to

http://aeotec.com/z-wave-gateways

Declaration of Conformity.

Aeotec Limited declares that TriSensor is in compliance with the essential requirements and other

relevant provisions of RED 2014/53/EU, RoHS 2011/65/EU, IEC62321:2008 and EN50581:2012.

Command Class Configuration

The device supports the controller to configure parameters of the device through Configuration

Command Class, and the device has 21 parameters available for users to set according to their

different needs:

Motion Retrigger Time

This parameter is configured the delay time before PIR sensor can be triggered again to

reset motion timeout counter. Value = 0 will disable PIR sensor from triggering until motion

timeout has finished.

Parameter Number

Size (Byte) Available Settings Default value

1 2 0 ~ 32767 30

Motion Clear Time

This parameter is configured the time to clear motion event after a motion event detected.

Time to motion clear, the device will send a clear event report to controller and send BASIC_SET

= 0x00 to nodes associated in group 2. Unit: Second.

Parameter Number

Size (Byte) Available Settings Default value

2 2 1 ~ 32767 240

Motion Sensitivity

This parameter is configured the sensitivity that motion detect.

0 – PIR sensor disabled.

1 – Lowest sensitivity.

11 – Highest sensitivity.

Parameter Number

Size (Byte) Available Settings Default value

3 1 0 ~ 11 11

Binary Sensor Report Enable

‘0’ –Disable sensor binary report when motion event is detected or cleared.

‘1’ –Enable sensor binary report when motion event is detected or cleared.

Parameter Number

Size (Byte) Available Settings Default value

4 1 0 , 1 0

Disable BASIC_SET to Associated nodes

This parameter is configured the enabled or disabled send BASIC_SET command to nodes

that associated in group 2 and group 3.

0 – Disabled All Group Basic Set Command

1 – Enabled Group 2 Basic Set Command, Group 3 Basic Set Command is

disabled. 2 – Enabled Group 3 Basic Set Command, Group 2 Basic Set

Command is disabled. 3 – Enabled Group 2 and Group 3 Basic Set Command.

Parameter Number

Size (Byte) Available Settings Default value

5 1 0 ~ 3 3

Basic Set Value Settings for Group 2

‘0’ – Send BASIC_SET = 0xFF to devices associated in Group 2 when motion event is

triggered, send BASIC_SET = 0x00 to devices associated in group 2 when motion event is

cleared.

‘1’– Send BASIC_SET = 0x00 to devices associated in Group 2 when motion event is

triggered, send BASIC_SET = 0xFF to devices associated in group 2 when motion event is

cleared.

‘2’ – Send BASIC_SET = 0xFF to devices associated in Group 2 when motion event is

triggered.

‘3’ – Send BASIC_SET = 0x00 to devices associated in Group 2 when motion event is

triggered.

‘4’ – Send BASIC_SET = 0x00 to devices associated in Group 2 when motion event is

cleared. ‘5’ – Send BASIC_SET = 0xFF to devices associated in Group 2 when motion event

is cleared.

Parameter Number

Size (Byte) Available Settings Default value

6 1 0 ~ 5 0

Temperature Alarm Value

This parameter is configured the threshold value that alarm level for temperature. When the

current ambient temperature value is larger than this configuration value, device will send a

BASIC_SET = 0xFF to nodes associated in group 3. If current temperature value is less than

this value, device will send a BASIC_SET = 0x00 to nodes associated in group 3.

Value = [Value] × 0.1(Celsius / Fahrenheit)

Parameter Number

Size (Byte) Available Settings Default value

7 EU/AU

2 -400~850 (Celsius) 239 (Celsius)

US 2 -400~1185 (Fahrenheit) 750 (Fahrenheit)

Led Indicate Disable

This parameter is configured the Led light on disable or enable.

‘1’ – Enable Led Blink when device detects a motion event.

‘0’ – Disable Led Blink. This configuration is not affect inclusion, exclusion and reset.

Parameter Number

Size (Byte) Available Settings Default value

10 1 0, 1 1

Led Color For Motion Event Report

‘0’ – Disable.

‘1’ – Red.

‘2’ – Green.

‘3’ – Blue.

‘4’ – Yellow.

‘5’ – Pink.

‘6’ – Cyan.

‘7’ – Purple.

‘8’ – Orange.

Parameter Number

Size (Byte) Available Settings Default value

11 1 0 ~ 8 2

10)

Led Color For Temperature Sensor Report

‘0’ – Disable.

‘1’ – Red.

‘2’ –Green.

‘3’ – Blue.

‘4’ – Yellow.

‘5’ – Pink.

‘6’ – Cyan.

‘7’ – Purple.

‘8’ – Orange.

Parameter Number

Size (Byte) Available Settings Default value

12 1 0 ~ 8 0

11)

Led Color For Light Sensor Report

‘0’ – Disable.

‘1’ – Red.

‘2’ –Green.

‘3’ – Blue.

‘4’ – Yellow.

‘5’ – Pink.

‘6’ – Cyan.

‘7’ – Purple.

‘8’ – Orange.

Parameter Number

Size (Byte) Available Settings Default value

13 1 0 ~ 8 0

12)

Led Color For Battery Report

‘0’ – Disable.

‘1’ – Red.

‘2’ –Green.

‘3’ – Blue.

‘4’ – Yellow.

‘5’ – Pink.

‘6’ – Cyan.

‘7’ – Purple.

‘8’ – Orange.

Parameter Number

Size (Byte) Available Settings Default value

14 1 0 ~ 8 0

13)

Led Color For Wakeup Notification Report

‘0’ – Disable.

‘1’ – Red.

‘2’ –Green.

‘3’ – Blue.

‘4’ – Yellow.

‘5’ – Pink.

‘6’ – Cyan.

‘7’ – Purple.

‘8’ – Orange.

Parameter Number

Size (Byte) Available Settings Default value

15 1 0 ~ 8 0

14)

Temperature Scale Setting

Configure temperature sensor scale type, Temperature to report in Celsius or Fahrenheit.

0 – Celsius (C).

1 – Fahrenheit (F).

Parameter Number

Size (Byte) Available Settings Default value

20 EU/AU

1 0, 1 0

US 1 0, 1 1

15)

Temperature Threshold Value to Report

Change threshold value for change in temperature to induce an automatic report for

temperature sensor. Scale is identical setting in Parameter No.20.

Setting of value 20 can be a change of -2.0 or +2.0 (C or F depending on Parameter No.20)

to induce automatic report or setting a value of 2 will be a change of 0.2(C or F).

Parameter Number

Size (Byte) Available Settings Default value

21 2 0~ 250 20

16)

Light intensity Threshold Value to Report

Change threshold value for change in light sensor to induce an automatic report for

temperature sensor. Scale: Lux.

Parameter Number

Size (Byte) Available Settings Default value

22 2 0~ 10000 100

17)

Temperature Sensor Report Interval

This parameter is configured the time interval for temperature sensor report. This value is

larger, the battery life is longer. And the temperature value changed is not obvious.

Unit: Second.

Parameter Number

Size (Byte) Available Settings Default value

23 2 1 - 32767 3600

18)

Light Sensor Report Interval

This parameter is configured the time interval for light sensor report. This value is larger, the

battery life is longer. And the light intensity changed is not obvious.

Unit: Second.

Parameter Number

Size (Byte) Available Settings Default value

24 2 1 - 32767 3600

19)

Temperature Offset Value

The current measuring temperature value can be add and minus a value by this setting.

The scale can be decided by Parameter Number 20.

Temperature Offset Value = [Value] * 0.1(Celsius / Fahrenheit)

Parameter Number

Size (Byte) Available Settings Default value

30 2 -200 ~ 200 0

20)

Light Intensity Offset Value

The current measuring light intensity value can be add and minus a value by this

setting.

Parameter Number

Size (Byte) Available Settings Default value

31 2 -1000 ~ 1000 0

21)

Light Sensor Calibrated Coefficient

This configuration defines the calibrated scale for ambient light intensity. Because the

method and position that the sensor mounted and the cover of sensor will bring

measurement error, user can get more real light intensity by this parameter setting. User

should run the steps as blows for calibrating

Set this parameter value to default (Assumes the sensor has been added in a Z-

Wave Network).

Place a digital luxmeter close to sensor and keep the same direction, monitor the light

intensity value (Vm) which report to controller and record it. The same time user

should record the value (Vs) of luxmeter.

The scale calibration formula: k = Vm / Vs.

The value of k is then multiplied by 1024 and rounded to the nearest whole number.

Set the value getting in 5) to this parameter, calibrate finished.

For example, Vm = 300, Vs =

2600, then k = 2600 / 300 =

8.6667

k = 8.6667 * 1024 = 8874.7 ≈ 8875

The parameter should be set to 8875.

Parameter Number

Size (Byte) Available Settings Default value

100 2 1~32767 1024

All Supports Command Class

This device supports Z-Wave Command Class as follows:

* COMMAND_CLASS_ZWAVEPLUS_INFO (V2)

* COMMAND_CLASS_SECURITY (V1)

* COMMAND_CLASS_SECURITY_2 (V1)

* COMMAND_CLASS_TRANSPORT_SERVICE (V2)

* COMMAND_CLASS_VERSION (V2)

* COMMAND_CLASS_POWERLEVEL (V1)

* COMMAND_CLASS_ASSOCIATION (V2)

* COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION (V3)

* COMMAND_CLASS_ASSOCIATION_GRP_INFO (V1)

* COMMAND_CLASS_MANUFACTURER_SPECIFIC (V2)

* COMMAND_CLASS_DEVICE_RESET_LOCALLY (V1)

* COMMAND_CLASS_BATTERY (V1)

* COMMAND_CLASS_WAKEUP (V2)

* COMMAND_CLASS_NOTIFICATION (V8)

* COMMAND_CLASS_SENSOR_BINARY (V2)

* COMMAND_CLASS_SENSOR_MULTILEVEL (V7)

* COMMAND_CLASS_CONFIGURATION (V1)

* COMMAND_CLASS_SUPERVISION (V1)

The full text of the declaration is available from https://support.aeotec.com/trisensor/doc

Specifications.Z-Wave devices operate between 868.40 & 926.30 MHz depending on local

restrictions. It uses up to -0.36dBm ERP transmit power, enabling long range connectivity. Full

information on device specifications and certifications at support.aeotec.com/trisensor/specs

California Proposition 65. WARNING: This product contains a chemical known to the State of

California to cause birth defects or other reproductive harm. Use only for intended purposes. Do

not use for other purposes including, but not limited to, the consumption of food and drinks.

Andere Aeotec Zubehör Handbücher

Aeotec

Aeotec MultiSensor 7 Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Door / Window Sensor 7 Bedienungsanleitung

Aeotec

Aeotec GP-AEOWLSEU Bedienungsanleitung

Aeotec

Aeotec MultiSensor Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Door / Window Sensor 7 Bedienungsanleitung

Aeotec

Aeotec Recessed Door Sensor 7 Bedienungsanleitung

Aeotec

Aeotec TriSensor Bedienungsanleitung

Aeotec

Aeotec Z-Wave Multisensor DSB05-ZWEU Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec Z-Wave MultiSensor 6 Bedienungsanleitung

Aeotec

Aeotec Siren 6 Bedienungsanleitung

Aeotec

Aeotec GP-AEOMPSEU Bedienungsanleitung

Aeotec

Aeotec Door / Window Sensor 7 Bedienungsanleitung

Aeotec

Aeotec ZW089 Bedienungsanleitung

Aeotec

Aeotec DSB05106-ZWUS Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec MULTISENSOR 6 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Aeotec

Aeotec AEOEZW112 Bedienungsanleitung

Aeotec

Aeotec Smart Switch 7 ZWA023 Bedienungsanleitung

Aeotec

Aeotec Water Sensor 7 Pro Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung