Afag SA-1 Series Bedienungsanleitung

Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5 1–52

Assembly and operating instructions

Telescope spindle axis

SA-1 ISA-1-FL

Translation of the Original Assembly Instructions EN

SA-1-050 Order no.: 50249011

SA-1-050-FL Order no.: 50471882

SA-1-100 Order no.: 50249013

SA-1-100-FL Order no.: 50471883

SA-1-150 Order no.: 50249014

SA-1-150-FL Order no.: 50471884

2 – 52 Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5

Dear Customer,

Thank you for choosing our products and placing your trust and confidence in

our company!

These assembly and operating instructions contain all essential information you

need about your product. Our aim is to provide the required information as

concisely and clearly as possible. If, however, you still have any questions on

the contents or suggestions, please do not hesitate to contact us. We are always

grateful for any feedback.

Our team will also be glad to answer any further question you may have

regarding the telescope spindle axis or other options.

We wish you every success with our products!

With kind regards

Your Afag team

The modules have been designed by Afag Automation AG according to the state

of the art. Due to the constant technical development and improvement of our

products, we reserve the right to make technical changes at any time.

All contents of the present assembly and operating instructions, in particular the

No part of these assembly and operating instructions may be reproduced,

distributed (made available to third parties), or transmitted in any form or by any

means, including photocopying, recording, or other electronic or mechanical

methods, without the prior written permission of Afag Automation AG.

Afag Automation AG

Fiechtenstrasse 32

CH - 4950 Huttwil (Switzerland)

Tel.: +41 62 959 86 86

Fax.: +41 62 959 87 87

e-mail: sales@afag.com

Internet: www.afag.com

Table of contents

Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5 3–52

Table of contents

1General .................................................................................................................... 5

1.1 Contents and purpose of these assembly instructions................................. 5

1.2 Explanation of symbols................................................................................. 5

1.3 Additional symbols........................................................................................ 6

1.4 Applicable documents .................................................................................. 7

1.5 Warranty ....................................................................................................... 7

1.6 Liability.......................................................................................................... 7

2Safety instructions................................................................................................. 8

2.1 General ......................................................................................................... 8

2.2 Intended use ................................................................................................. 8

2.3 Foreseeable misuse ..................................................................................... 8

2.4 Obligations of the operator and the personnel ............................................. 9

2.4.1 Observe the assembly instructions ........................................................ 9

2.4.2 Obligations of the operating company.................................................... 9

2.4.3 Obligations of the personnel ................................................................ 10

2.5 Personnel requirements ............................................................................. 10

2.5.1 Personnel qualification ......................................................................... 10

2.6 Personal protective equipment (PPE) ........................................................ 11

2.7 Changes & modifications............................................................................ 11

2.8 General hazards / residual risks................................................................. 12

2.8.1 General hazards at the workplace ....................................................... 12

2.8.1 Mechanical hazards ............................................................................. 13

2.8.2 Danger due to electricity ...................................................................... 13

2.8.3 Noise hazards ...................................................................................... 13

2.8.4 Danger due to high temperatures ........................................................ 14

2.8.5 Safety labels (warning symbols) .......................................................... 14

3Technical data ...................................................................................................... 15

3.1 Dimension drawing SA-1 and SA-1-FL ...................................................... 15

3.2 Technical data SA-1 and SA-1-FL.............................................................. 16

3.3 Preferred combinations SA-1 and SA-1-FL................................................ 17

4Transport, Packaging and Storage .................................................................... 18

4.1 Safety instructions for transport.................................................................. 18

4.2 Scope of supply .......................................................................................... 18

4.3 Transport .................................................................................................... 19

4.4 Packaging ................................................................................................... 19

4.5 Storage ....................................................................................................... 19

5Structure and description ................................................................................... 20

5.1 Structure telescope spindle axis................................................................. 20

5.2 Product description..................................................................................... 20

5.3 Accessories ................................................................................................ 21

Table of contents

4 – 52 Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5

6Installation, assembly & setting ......................................................................... 22

6.1 Safety Instructions for Installation & Assembly .......................................... 22

6.2 Assembly & attachment.............................................................................. 23

6.2.1 Fastening the module........................................................................... 23

6.2.2 Tightening torques................................................................................ 23

6.2.3 Attachment grid and centering bushings.............................................. 24

6.2.4 Load on the telescope spindle axis ...................................................... 25

6.2.5 Load diagrams...................................................................................... 26

6.3 Motor layout................................................................................................ 27

6.3.1 Arrangement options............................................................................ 27

6.3.2 Adjusting the motor position................................................................. 28

6.3.3 Motor control ........................................................................................ 29

6.4 Afag standard controllers ........................................................................... 30

6.4.1SE-48 Controller................................................................................... 30

6.4.2 SE-Power for control cabinet mounting................................................ 32

6.4.3 Servo controller .................................................................................... 34

6.5 Programming of the telescope spindle axis................................................ 35

6.5.1 Safety instructions for programming .................................................... 35

6.5.2 Programming........................................................................................ 35

7Commissioning .................................................................................................... 36

7.1 Safety instructions for commissioning ........................................................ 36

7.2 Preparatory activities for commissioning.................................................... 37

7.3 Commissioning of the modules .................................................................. 37

7.4 Setting up & retrofitting ............................................................................... 38

8Fault elimination................................................................................................... 39

8.1 Safety instructions for troubleshooting ....................................................... 39

8.2 Fault causes and remedy ........................................................................... 40

9Maintenance and Repair...................................................................................... 41

9.1 General notes ............................................................................................. 41

9.2 Safety instructions for Maintenance and Repair ........................................ 41

9.3 Maintenance activities and maintenance intervals ..................................... 42

9.3.1 Overview of the maintenance points .................................................... 42

9.3.2 Lubrication of spindle gear ................................................................... 43

9.3.3 Lubrication of linear guide .................................................................... 44

9.3.4 Further maintenance ............................................................................ 45

9.4 Spare parts and repair work ....................................................................... 45

10 Decommissioning, disassembly, disposal........................................................ 46

10.1 Safety instructions for decommissioning and disposal............................... 46

10.2 Decommissioning ....................................................................................... 46

10.3 Disposal...................................................................................................... 46

11 Declaration of incorporation............................................................................... 47

General

Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5 5–52

1 General

1.1 Contents and purpose of these assembly instructions

These assembly instructions contain important information on assembly,

commissioning, functioning and maintenance of the telescope spindle axis SA-

1 and SA-1-FL to ensure safe and efficient handling and operation.

Consistent compliance with these assembly instructions will ensure:

permanent operational reliability of the telescope spindle axis,

optimal functioning of the telescope spindle axis,

timely detection and elimination of defects (thereby reducing maintenance

and repair costs),

prolongation of the telescope spindle axis service life.

The illustrations in this manual shall provide you with a basic understanding of

the module and may vary from the actual design of your module.

1.2 Explanation of symbols

The safety notes are marked by a pictogram and a signal word. The safety notes

describe the extent of the hazard.

DANGER

Danger!

This safety note indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING

Warning!

This safety note points out a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

Caution!

This safety note points out a potentially dangerous situation which, if not

avoided, can result in minor or slight injuries.

NOTICE

This safety note points out a potentially dangerous situation which, if not

avoided, can cause substantial damage to property and the environment.

General

6 – 52 Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5

This note contains important additional information as well as useful tips for

safe, efficient and trouble-free operation of the module.

Further warning signs:

Where applicable, the following standardised symbols are used in this manual

to point out the various potential health risks.

Warning

- Dangerous electrical voltage.

Warning

- Risk of injury from contact with hot surfaces.

Warning

Risk of hand and finger injury due to uncontrolled

movements of components.

Warning

- Magnetic field.

Warning

- back injury due to heavy lifting.

Warning

- Risk of injury as a result of parts being flung out!

Warning

-high noise levels.

1.3 Additional symbols

In these assembly instructions the following symbols are used to highlight

instructions, results, references, etc..

Symbol Description

1. Instructions (steps ...)

 Results of actions

 References to sections

 Enumerations not ordered

General

Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5 7–52

1.4 Applicable documents

Each telescope spindle axis is accompanied by a safety information sheet.

This information sheet must be read carefully by every person who carries out

work on and with the telescope spindle axis.

1.5 Warranty

The warranty terms for Afag handling components and handling systems are

the following:

24 months from initial operation and up to a maximum of 27 months from

delivery.

Wear parts are excluded from the warranty (The customer is entitled to a

product free of defects. This does also apply to defective accessories and

wear parts. Normal wear and tear are excluded from the warranty.

The warranty covers the replacement or repair of defective Afag parts. Further

claims are excluded.

The warranty shall expire in the following cases:

Improper use of the module.

Non-observance of the instructions regarding assembly, commissioning,

operation and maintenance of the module.

Improper assembly, commissioning, operation and maintenance.

Repairs and design changes carried out without prior technical instructions

of Afag Automation AG.

Removing the serial number from the product.

Inadequate checking of wear parts.

Non-observance of the EC Machinery Directive, the Accident Prevention

Regulations, the Standards of the German Electrotechnology Association

(VDE) and these safety and assembly instructions.

1.6 Liability

No changes shall be made to the telescope spindle axis unless described in this

instructions manual or approved in writing by Afag Automation AG.

Afag Automation AG accepts no liability for unauthorized changes or improper

assembly, installation, commissioning, operation, maintenance or repair work.

Safety instructions

8 – 52 Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5

2 Safety instructions

2.1 General

This chapter provides an overview of all important safety aspects to ensure safe

and proper use of the telescope spindle axis and optimal protection of

personnel.

Safe handling and trouble-free operation of the telescope spindle axis requires

knowledge of the basic safety regulations.

Every person carrying out installation, commissioning, maintenance work or

operating the telescope spindle axis must have read and understood the

complete user manual, especially the chapter on safety instructions.

Beyond this, there are rules and regulations regarding accident prevention that

are applicable to the place of installation which must be observed.

Improper use may result in danger to life and limb of the user or third parties or

in damage to the automation system or other material assets.

Failure to follow the directions and safety instructions given in this instructions

manual may result in serious hazards.

2.2 Intended use

The telescope spindle axis series SA-1 and SA-1-FL is designed for the shock-

free linear movement of permanently mounted loads in non-explosive

environments and in the ambient and operating conditions defined for these

modules (technical data sheet in the handling catalogue).

Any use beyond the described purpose is considered to be not in accordance

with the intended use.

The intended use of the module also includes:

observance of all instructions given in this instructions manual,



compliance with the inspection and maintenance work and the

specifications in the data sheets,

using only original spare parts.

2.3 Foreseeable misuse

Any use other than or beyond the intended use described above is considered

a misuse of the telescope spindle axis.

Especially the following use is considered a misuse:

Use in potentially explosive atmospheres

Safety instructions

Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5 9–52

Risks can occur if the module is not used as intended. In the event of

damages caused by improper use the following shall apply:

the operating company shall be solely responsible for such damage, and

Afag does not accept any liability for damages caused by improper use.

2.4 Obligations of the operator and the personnel

2.4.1 Observe the assembly instructions

A basic prerequisite for safe and proper handling of the telescope spindle axis

is a good knowledge of the basic safety instructions.

These assembly instructions, in particular the safety instructions contained

therein, must be observed by all persons working with the telescope spindle

axis.

2.4.2 Obligations of the operating company

In addition to the safety instructions given in this manual, the operating company

must comply with the safety, accident prevention and environmental protection

regulations valid for the field of application of the telescope spindle axis.

The operating company is required to use only personnel who:

have the necessary professional qualifications and experience,

are familiar with the basic rules regarding occupational safety and accident

prevention,

have been instructed in the correct handling of the telescope spindle axis,

have read and understood these assembly instructions.

The operating company is also required to:

monitor on an ongoing basis that the personnel work safely considering any

potential hazard involved and the assembly instructions are observed,

ensure that the assembly instructions are always kept at hand at the

installation in which the modules are mounted,

observe and communicate universally applicable laws and regulations

regarding accident prevention and environmental protection,

provide the necessary personal protective equipment (e.g. protective

gloves) and instruct the personnel to wear it.

WARNING

Risk of injury if the module is not used as intended!

The improper use of the telescope spindle axis poses a potential hazard to

the personnel.



The telescope spindle axis may only be used in a technically perfect

condition in accordance with its intended use and the instructions in this

manual and in compliance with the safety requirements!



Any malfunctions, particularly those that could impair safety, must be

eliminated immediately!

Safety instructions

10 – 52 Assembly instructions EN SA-1 I SA-1-FL Edition 01/2021Rev. 3.5

2.4.3 Obligations of the personnel

All personnel working with the telescope spindle axis are required to:

read and observe these assembly instructions, especially the chapter on

safety,

observe the occupational safety and accident prevention regulations,

observe all safety and warning signs on the telescope spindle axis,

refrain from any activity that might compromise safety and health.

In addition, the personnel must wear the personal protecti

ve equipment

required for carrying out their work. (Chapter 2.6).

2.5 Personnel requirements

2.5.1 Personnel qualification

The activities described in the assembly instructions require specific requisites

at the level of professional qualifications of the personnel.

Personnel not having the required qualification will not be able to assess the

risks that may arise from the use of the telescope spindle axis thus exposing

himself and others to the risk of serious injury. Therefore, only qualified

personnel may be permitted to carry out the described activities on the telescope

spindle axis. Persons whose ability to react is restricted due to the intake of

medication or the like must not interact with the telescope spindle axis.

These installation instructions are intended for skilled personnel (installers,

system integrators, maintenance personnel, technicians), electricians and

operating personnel.

The following is a description of the professional skills (qualifications) required

for carrying out the different activities:

Qualified personnel:

Qualified personnel with

appropriate training who are qualified due to their

special know-how and fully familiar with the machine and who have been given

instructions on how to carry out the task entrusted to them safely.

Qualified electrician:

Perso

ns who have obtained their electrical qualifications through appropriate

professional training and complementary courses that enables them to identify

risks and prevent possible hazards resulting from electricity.

Operator (trained personnel):

Authorized persons

who due to their specialized professional training,

expertise and experience are capable of identifying risks and preventing

possible hazards arising from the use of the machine.

Andere Handbücher für SA-1 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Afag Zubehör Handbücher

Afag

Afag Flipband 200 Produkthandbuch

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung