AGCO Gleaner S67 Bedienungsanleitung

Quick Reference Guide

S67/S68/S96 • S77/S78/S97 • S88/S98 Models

It is YOUR responsibility to read and understand the safety section in your

Operator’s Manual and the manual for all attachments before operating your

machine. Remember YOU are the key to safety. Good safety practices not only

protect you, but also the people around you.

Study the features in your Operator’s Manual and make them a working part of

your safety program. Keep in mind that the safety section in your Operator’s

Manual is written only for this type of machine. Practice all other usual and

customary safe working precautions, and above all REMEMBER -SAFETY IS

YOUR RESPONSIBILITY. YOU CAN PREVENT SERIOUS INJURY OR

DEATH.

Contents

Combine Setup

•Cereal Grain –Wheat. Oats,Barley 1

•Mile-Grain-Sorgum 2

•Dry Corn (< 20% Moisture) 2

•High Moisture Corn (> 24% Moisture) 3

•Soybeans 4

•Canola/Rapeseed 5

•Millet 5

•Edible Beans 6

•Sunflowers 7

•Flax 7

•Grass Seed (Bluegrass, Bentgrass) 8

•Alfalfa 9

•Industrial Hemp 10

•Clover 11

•Rye 11

Troubleshooting

•Header 12

•Feed Conveyer 17

•Processor 18

•Grain Quality 20

•Grain Loss 24

Loss Calculation

•“Quick Check” For Combine Grain Loss 26

•Spreading Discharge 26

•“Next Step” For Combine Grain Loss 26

•Rotor Loss 27

•Shoe Loss 27

•“Advanced” Grain Loss Calculation Procedure 28

•Advanced Rotor Loss 28

•Advanced Shoe Loss 28

Standard Payable Moisture & Density Chart 29

Booking and Transfer of Yield Data and Auto-Guide lines

(includes deleting Yeild and Auto-Guide) 30

Combine Setup

Cereal Grain -Wheat, Oats, Barley

Initial Combine Setup

Crop

Rotor

RPM

Conca

Setting

Fan

Opening

Chaff

Openi

Sieve

Openi

Chopp

Speed

Elevat

Boots

Wheat 750 0.1” -

0.2” 5 - 7 0.75”

(19 mm)

0.375”

(10mm) Fast Solid

Oats 600 0.1” -

0.2” 3 - 6 0.75”

(19 mm)

0.375”

(10mm) Fast Solid

Barley 750 0.1” -

0.2” 5 - 7 0.75”

(19 mm)

0.375”

(10mm) Fast Solid

* -As read on the Tyton™ terminal on the S9 Series or EIP on S8 and S7 Series.

Initial Header & Header Drive Setup

•Cutterbar locked up on flex headers.

•Variable speed header drive in slowest position.

•Right-hand pivot drive belt positioned on large countershaft drive

sheave.

•Left separator cage cover should be required for all cereal crops.

Straw Chopper

•Position chopper drive belt so chopper is operating at fast speed.

Tips

•Filler bars may be required for hard threshing cereals to eliminate white

caps.Order Concave Filler Bar #71440060 from your dealer. Filler bars

come standard with the machine MY14 to current.

•If white caps persist after suggested configuration changes have been

made, a1/2" thresher bar #71485652 option is available.

Milo -Grain Sorghum

Initial Combine Setup

Rotor

RPM

Concave

Setting

Fan

Opening

Chaffer

Opening

Sieve

Opening

Chopper

Speed

Elevato

Boots

450-600 0.2” -0.4” 5 - 7 0.625”

(16mm)

0.313”

(8mm) Fast Solid

•Set concave to stem thickness just below head for starting point.

•Run in low range of rotor gearbox for greater torque if possible (S8

Series has greater range to provide ability to run on low side of

gearbox). Running in the low RPM's of the high range will increase

belt slip which reduces belt life.

Initial Header & Header Drive Setup

•Lock up cutterbar on flex headers.

•Variable speed header drive in slowest position.

•Right-hand pivot drive belt positioned on large countershaft drive

sheave.

•Left separator cage cover should be required for all cereal crops.

Straw Chopper

•Position chopper drive belt so chopper is operating at fast speed.

Dry Corn (< 20% moisture)

Initial Combine Setup

Rotor

RPM

Concave

Setting

Fan

Opening

Chaffer

Opening

Sieve

Openin

Chopper

Speed

Elevato

Boots

250-300 0.6” -0.8” 5 - 7 0.625”

(16mm)

0.4”

(11 mm)* Slow Solid

•Feed chains at slow speed for corn

•IMPORTANT: Set chaffer to achieve acceptable grain bin sample.

Opening chaffer can be done anytime. However, due to the natureof

the electronics, closing the chaffer should be done at the end of the

field after cleanout by completely opening and then closing to the

lower number that you desire and then adjusting up to the desired

chaffer setting.

Initial Header & Header Drive Setup

•Variable speed header drive hose and coupler should be

connected.

•Right-hand pivot drive belt positioned on small countershaft

drive sheave.

Tips

•Use round end corn chaffer for higher moisture corn.

•A grain chaffer is optional, but corn chaffer is recommended.

•*Removal of lower sieve will increase capacity in higher yielding

corn. 2

High Moisture Corn (> 24% moisture)

Initial Combine Setup

Rotor RPM

Concave

Setting

Fan

Opening

Chaffer

Opening

Sieve

Opening

Chopper

Speed

Elevato

Boots

250-300 0.6” -0.8” 5 - 7 0.625”

(16 mm) *

Remove

lower

sieve Slow Solid

•* IMPORTANT: Set chaffer to achieve acceptable grain bin sample.

Opening chaffer can be done anytime. However, due to the nature of the

electronics, closing the chaffer should be done at the end of the field

after cleanout by completely opening and then closing to the lower

number that you desire and then adjusting up to the desired chaffer

setting.

•Feed chains at slow speed for corn.

Initial Header & Header Drive Setup

•Variable speed header drive hose and coupler should be connected.

•Right-hand pivot drive belt positioned on small countershaft drive

sheave.

Tips

•Use round end corn chaffer for higher moisture corn.

•Use grain chaffer for drier corn. This is also useful when frequently

switching between corn and soybean harvest.

•Removal of lower sieve will increase capacity in higher yielding, high

moisture corn.

•In high moisture corn with wet green leaves, start at 350 RPM to optimize

performance and eliminate any chance for plugging of processor with crop

residue which could result in rotor loss. Increase in 20 RPM increments up

to a maximum of 400 RPM in these wet green leaves for desired

performance.

Soybeans

Initial Combine Setup

Rotor RPM

Concave

Setting

Fan

Opening

Chaffer

Openin

Sieve

Opening

Chopper

Speed

Elevato

Boots

400 0.2” -0.4” 5 - 7 0.75”

(19 mm)*

0.375”

(10mm) Fast Solid

•*Use suggested settings with standard chaffer or use .6" (15 mm) with

corn chaffer

Initial Header & Header Drive Setup

•Release and adjust cutterbar on flex headers. Adjust header height

control.

•Variable speed header drive in slowest position.

•Right-hand pivot drive belt positioned on large countershaft drive

sheave.

Tips

•Round-end corn chaffer can remain in combine for soybeans however, if

grain sample quality needs to be improved, standard chaffer is available.

•Left-hand separator cage cover and chopper floor cover are required for

soybeans.

•Retractable stationary knives should be left in the lower position in

soybeans. If additional chop of residue is required, the stationary knives

should be partially raised up in small increments to avoid excessive power

requirements. The 24-knife chopper available on S7 Series, standard on

all S8 Series and S9 Series, will provide adequate chop in most cases.

Canola/Rapeseed

Initial Combine Setup

Rotor RPM

Concave

Setting

Fan

Opening

Chaffer

Opening

Sieve

Opening

Chopper

Speed

Elevato

Boots

400-600 0.2” -0.4” 3 - 5 0.75”

(19 mm)

0.375”

(10mm) Fast Solid

Initial Header & Header Drive Setup

•Variable speed header drive (if equipped) in slowest position for draper

headers and direct cut headers.

•Right-hand pivot drive belt positioned on large countershaft drive sheave.

•Feed chains (front and rear) should be in high position and fast speed.

•Angle pickup header down so pickup attachment and pickup header auger

can breakup clumps of crop material and more evenly feed the feed chains.

Lower wind board accordingly.

Tips

•During day in dry conditions, slow the rotor down; at night when conditions

are damp speed rotor up.

•Feeder house optimization instructions for R Series, S7 and S8 Series are

available at your Gleaner dealer to increase capacity in canola.

Millet

Initial Combine Setup

Rotor RPM

Concave

Setting

Fan

Opening

Chaffer

Opening

Sieve

Opening

Chopper

Speed

Elevato

Boots

525 0.2” -0.3” 2 - 4 0.625”

(16mm)

0.1875”

(5mm) Fast Solid

•Blanks may be required.

Initial Header & Header Drive Setup

•Variable speed header drive (if equipped) in slowest position for draper

headers and direct cut headers.

•Right-hand pivot drive belt positioned on large countershaft drive sheave.

•Feed chains (front and rear) should be in high position and fast speed.

•Angle pickup header down so pickup attachment and pickup header auger

can breakup clumps of crop material and more evenly feed the feed chains

and lower wind board accordingly.

Tips

•During day in dry conditions, slow the rotor down; at night when

conditions are damp speed rotor up.

Edible Beans

Initial Combine Setup

Rotor RPM

Concave

Setting

Fan

Opening

Chaffer

Opening

Sieve

Opening

Chopper

Speed

Elevato

Boots

190 -230 0.3” -0.4” 5 - 7 0.75”

(19 mm)

0.375”

(10mm) Fast Solid

•Remove all reverse bars and replace with forward bars and remove

separator knives if installed.

Initial Header & Header Drive Setup

•Cutter Bar -In some crops, the material is direct cut so the header should

be set-up accordingly. In many cases, the crop is windrowed and the

material is harvested from the windrow.

•Variable speed header drive in slowest position.

•Right-hand pivot drive belt positioned on large countershaft drive sheave

and small driven pivot sheave.

Tips

•Optional perforated boot covers on clean grain and tailings elevators may

be used if desired but, can cause cracking in certain conditions.

•Optional slow speed elevator kit may be used if desired. Order SlowSpeed

Elevator Kit #700963993G for machines built before January 1st 2018.

Kit #71474176G for machines built after December 31st 2017.

Additional Combine Setup

•If cracking of beans still occurs, remove all lugs on front accelerator roll

and leave lugs on rear accelerator roll to move crop. Lugs should be

reinstalled immediately for all other crops.

Sunflowers

Initial Combine Setup

Rotor

RPM

Concave

Setting

Fan

Opening

Chaffer

Opening

Sieve

Opening

Chopper

Speed

Elevato

Boots

450 0.4” 3 - 6 0.625”

(16mm)

0.25”

(6mm) Fast Solid

Initial Header & Header Drive Setup

•Header must be equipped with sunflower attachment to minimize headand

seed loss at the header.

•Variable speed header drive in slowest position.

•Right hand pivot drive belt positioned on large countershaft drive sheave.

Tips

•Deactivate SmartCooling™ hydraulic valve for sunflowers.

Additional Combine Setup

•May require additional Separator Blanking Kit #700961967 (3 blanks)

will block off separator grates and level out shoe distribution. Please have

your dealer contact Technical Service Support.

Flax

Initial Combine Setup

Rotor

RPM

Concave

Setting

Fan Opening

Chaffer

Opening

Sieve

Opening

Chopper

Speed

Elevato

Boots

800 0.0” -0.4” 3 - 5 0.625”

(16mm)

0.125”

(3mm) Fast Solid

Initial Header & Header Drive Setup

•Flax is generally windrowed and a pickup attachment is used on

header.

•Variable speed header drive in slowest position.

•Right-hand pivot drive belt positioned on large countershaft drive

sheave and small driven pivot sheave.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AGCO Landwirtschaftliche Geräte Handbücher

AGCO

AGCO 5270C Bedienungsanleitung

AGCO

AGCO Combine FENDT 8300 Bedienungsanleitung

AGCO

AGCO Massey Ferguson 9195 Bedienungsanleitung

AGCO

AGCO FENDT CARGO Bedienungsanleitung

AGCO

AGCO Glencoe DR8700 Bedienungsanleitung

AGCO

AGCO Hawkeye RoGator RG900 Bedienungsanleitung

AGCO

AGCO FENDT 9300R Bedienungsanleitung

AGCO

AGCO GSI 54 Bedienungsanleitung

AGCO

AGCO Challenger RoGator 600C Bedienungsanleitung

AGCO

AGCO GSI PNEG-2064 Bedienungsanleitung

AGCO

AGCO FENDT 870N Bedienungsanleitung

AGCO

AGCO HayBoss G2 445, HayBoss G2 450 Bedienungsanleitung

AGCO

AGCO Gleaner DynaFlex 9250 Bedienungsanleitung

AGCO

AGCO Challenger Terra Gator 3244 Bedienungsanleitung

AGCO

AGCO LELY ATTIS PT 130 Bedienungsanleitung

AGCO

AGCO Glencoe CC4450 Bedienungsanleitung

AGCO

AGCO Glencoe SF4500 Bedienungsanleitung

AGCO

AGCO HayBoss G2 600A1 Bedienungsanleitung

AGCO

AGCO GSI PNEG-1826 Bedienungsanleitung

AGCO

AGCO HayBoss G2 644A Bedienungsanleitung

AGCO

AGCO Valtra BC 800 Bedienungsanleitung

AGCO

AGCO Massey Ferguson 8516 Bedienungsanleitung

AGCO

AGCO Gleaner 3200 Series Bedienungsanleitung

AGCO

AGCO GLEANER 3000 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung