Agilent Technologies 1168/9A Bedienungsanleitung

Agilent Technologies

Agilent 1168/9A

Differential and

Single-Ended Probes

User’s Guide

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Agilent

Technologies, Inc. as governed by United

States and international copyright laws.

Manual Part Number

01169-97017

Edition

September 2013

Designed in USA

Agilent Technologies, Inc.

Oscilloscope Products Division

Warranty

The material contained in this document is

provided “as is,” and is subject to being

changed, without notice, in future editions.

Further, to the maximum extent permitted

by applicable law, Agilent disclaims all war-

ranties, either express or implied, with

regard to this manual and any information

contained herein, including but not limited

to the implied warranties of merchantability

and fitness for a particular purpose. Agilent

shall not be liable for errors or for incidental

or consequential damages in connection

with the furnishing, use, or performance of

this document or of any information con-

tained herein. Should Agilent and the user

have a separate written agreement with

warranty terms covering the material in this

document that conflict with these terms,

the warranty terms in the separate agree-

ment shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

If software is for use in the performance of a

U.S. Government prime contract or subcon-

tract, Software is delivered and licensed as

"Commercial computer software" as

defined in DFAR 252.227-7014 (June 1995),

or as a "commercial item" as defined in FAR

2.101(a) or as "Restricted computer soft-

ware" as defined in FAR 52.227-19 (June

1987) or any equivalent agency regulation or

contract clause. Use, duplication or disclo-

sure of Software is subject to Agilent Tech-

nologies’ standard commercial license

terms, and non-DOD Departments and

Agencies of the U.S. Government will

receive no greater than Restricted Rights as

defined in FAR 52.227-19(c)(1-2) (June

1987). U.S. Government users will receive

no greater than Limited Rights as defined in

FAR 52.227-14 (June 1987) or DFAR

252.227-7015 (b)(2) (November 1995), as

applicable in any technical data.

Instrument Markings

The CE mark is a registered trade-

mark of the European Community.

ISM GRP 1-A denotes the instru-

ment is an Industrial Scientific and Medical

Group 1 Class A product. ICES/NMB-001

indicates product compliance with the

Canadian Interference-Causing Equipment

Standard.

This product complies with the

WEEE Directive (2002/96/EC)

marking requirements. The

affixed label indicates that you

must not discard this electri-

cal/electronic product in domestic house-

hold waste. Product Category: With

reference to the equipment types in the

WEEE Directive Annex I, this product is

classed as a “Monitoring and Control instru-

mentation” product. Do not dispose in

domestic household. To return unwanted

products, contact your local Agilent office,

or refer to www.agilent.com for more infor-

mation.

This symbol indicates the Envi-

ronmental Protection Use Period

(EPUP) for the product’s toxic

substances for the China RoHS require-

ments.

Safety Notices

CAUTION. A CAUTION notice

denotes a hazard. It calls attention to

an operating procedure, practice, or the

like that, if not correctly performed or

adhered to, could result in damage to

the product or loss of important data.

Do not proceed beyond a CAUTION

notice until the indicated conditions

are fully understood and met.

WARNING. A WARNING notice

denotes a hazard. It calls attention to

an operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result in

personal injury or death. Do not pro-

ceed beyond a WARNING notice until

the indicated conditions are fully

understood and met.

2 1168/9A Probes User’s Guide

Contents

1168/9A Probes User’s Guide 3

Contents

1Getting Started

Introduction 8

Supplied Accessories 12

Optional Probe Heads with Supplied Accessories 13

Optional E2669A Differential Connectivity Kit and Accessories 15

`Other Available Accessories 17

Probe Handling 25

Using the Velcro Dots 30

Using Offset With InfiniiMax Active Probes 31

Slew Rate Requirements for Different Technologies 33

Safety Information 34

Service 37

2Using Probe Heads

Recommended Configurations 42

Soldering a ZIF Tip to a DUT 79

Using N2884A Fine-Wire ZIF tips 84

N2887A/8A Soft Touch Probe Heads 95

3Maintaining Probe Heads

N5381/2A Probe Heads 106

N5451A Long-Wired ZIF Tips 111

E2677A/9A Solder-In Probe Heads 115

4Calibrating Probes

DC Gain and Offset Calibration 122

Calibration for Solder-In and Socketed Probe Heads 123

Calibration for Hand-Held Browser Probe Heads 131

N2887A & N2888A Calibration and Deskew Procedure 133

5Characteristics and Specifications

General 138

4 1168/9A Probes User’s Guide

Contents

InfiniiMax II Series with N5380B SMA Probe Head 141

Environmental 145

Probe Dimensions 146

6Performance Plots

N5380B SMA Probe Head (Full BW) 152

N5380B SMA Probe Head with the 1134A InfiniiMax Probe 155

N5381A & N5382A Differential Probe Heads (Full BW) 156

N5381A Differential Solder-in Probe Head with 2x Longer Wires 160

N5425A ZIF Probe Head (Full BW) 161

N5425A ZIF Probe Head with N5451A Long-Wired ZIF Tip 165

N5426A ZIF Probe Tip Impedance 180

E2675A Differential Browser 181

E2676A Single-Ended Browser 184

E2677A Differential Solder-in Probe Head (High BW) 187

E2678A Differential Socketed Probe Head (High BW) 190

E2678A Differential Socketed Probe Head w/ Damped Wire 193

E2679A Single-Ended Solder-In Probe Head (High BW) 196

E2695A SMA Probe Head 198

N2887A/N2888A Soft Touch Probe Heads 199

7Performance Verification

To Test Bandwidth 204

To Test Input Resistance 215

Performance Test Record 220

8SPICE Models

N5381A and N5382A Probe Heads 223

N5425A ZIF Probe Head with N5426A ZIF Tip Attached 226

N5426A ZIF Tip 229

N2887A/N2888A Probe Heads 232

InfiniiMax I Probe Heads 235

9Replacement Parts

E2675A Differential Browser Probe Head 246

E2677A Differential Solder-In Probe Head 246

E2678A Differential Socketed Probe Head 247

E2679A Single-Ended Solder-in Probe Head 248

Contents

1168/9A Probes User’s Guide 5

N5381A and N5382A Probe Heads 248

Other Accessories 249

6 1168/9A Probes User’s Guide

Contents

Agilent Technologies

Getting Started

Introduction 8

Supplied Accessories 12

Optional Probe Heads with Supplied Accessories 13

Optional E2669A Differential Connectivity Kit and Accessories 15

`Other Available Accessories 17

Probe Handling 25

Using the Velcro Dots 30

Using Offset With InfiniiMax Active Probes 31

Slew Rate Requirements for Different Technologies 33

Safety Information 34

Service 37

With the 1168A (10 GHz) and 1169A (12 GHz) probes, you

can probe differential and single- ended signals. The probes

provide a large common mode range for measuring

differential signals and a large offset range for measuring

single- ended signals. These probes are used at extreme

frequencies where off- board lead resistors cause undesirable

response variation. As a result, the 1168A and 1169A probes

were designed using resistor- at- the- tip technology where

resistors are located onto the very edge of the probe tip

board. The wires or probe tips in front of the resistors are

long enough to allow easy connection but are short enough

that any resonances caused by them are out of band and

don't impact the input impedance.

8 1168/9A Probe’s User’s Guide

1Getting Started

Introduction

Before you can use the probe, you must connect one of the

available probe heads to an 1168/9A probe amplifier.

Figure 1 Probe Amplifier with Attached Head

Probe Heads Figure 2 on page 9 shows the available probe heads and

accessories. Four different InfiniiMax II probe heads can

used including a Zero Insertion Force (ZIF) probe head that

uses a ZIF tip that can be installed at many locations on

your DUT. The ZIF tip’s small size is critical in probing tight

locations and the ZIF feature allows connection without

compressing the delicate wires which cannot support this

compression. You can also use the probe amplifiers with the

InfiniiMax I probe heads (with some limitations).

The differential probe heads offer easy measurement of

differential signals and greatly improve the measurement of

single- ended signals.

Each available probe head is documented in Chapter 2,

“Using Probe Heads”.

Getting Started 1

Introduction

1168/9A Probe’s User’s Guide 9

Figure 2 Available Probe Heads

10 1168/9A Probe’s User’s Guide

1Getting Started

Introduction

These probes can also be used with the 1143A external

power supply.

CAUTION Before using the probes, refer to “Probe Handling” on page 25.

WARNING Before using the probe, refer to “Safety Information” on page 34.

Compatible Oscilloscopes

Cleaning the probe If the probe requires cleaning, disconnect it from the

oscilloscope and clean it with a soft cloth dampened with a

mild soap and water solution. Make sure the probe is

completely dry before reconnecting it to the oscilloscope.

Channel Identification Rings When multiple probes are connected to the oscilloscope, use

the channel identification rings to associate the channel

inputs with each probe. Place one colored ring near the

probe’s channel connector and place an identical color ring

near the probe head.

Is Your Oscilloscope Software

Up-to-Date?

Agilent periodically releases

software updates to support your

probe, fix known defects, and

incorporate product enhancements.

To download the latest firmware, go

to www.agilent.com and search for

your oscilloscope’s topic. Click on

the “Drivers, Firmware & Software”

tab.

Table 1 Compatible Infiniium Oscilloscopes

Oscilloscope Model

90000 X-, and Q-Seriesa

a N5442A adapter required.

all

90000A Series all

86100C/D Seriesb

b N1022A/B adapter required.

all

80000B Series all

Inhaltsverzeichnis

Andere Agilent Technologies Laborausrüstung Handbücher

Agilent Technologies

Agilent Technologies 4150 TapeStation system Benutzerhandbuch

Agilent Technologies

Agilent Technologies Cary 630 FTIR Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1100 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6850 Series II Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6850 Series Bedienungs- und Montageanleitung

Agilent Technologies

Agilent Technologies 2200 TapeStation Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1200 Infinity Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1200 series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 850-DS Bedienungsanleitung

Agilent Technologies

Agilent Technologies 979 Bedienungs- und Sicherheitshinweise

Agilent Technologies

Agilent Technologies 6890 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1290 infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies BioCel 1200 Bedienungsanleitung

Agilent Technologies

Agilent Technologies BenchCel Microplate Handler Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7010 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5DX Bedienungsanleitung

Agilent Technologies

Agilent Technologies 280-DS MQS Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1290 Infinity Flexible Cube Bedienungsanleitung

Agilent Technologies

Agilent Technologies G1367A Bedienungsanleitung

Agilent Technologies

Agilent Technologies G2545A Gebrauchs- und Pflegehandbuch

Agilent Technologies

Agilent Technologies 1290 infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies Cary 8454 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1100 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1290 infinity Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Yamato

Yamato BM510 Bedienungsanleitung