Agilent Technologies 33120A Bedienungsanleitung

This guide contains information to install the Phase-Lock assembly into

the Agilent 33120A. This assembly can be installed only in instruments

shipped after August 1994 with serial numbers US34004078 and above.

Refer to the Agilent 33120A/Option 001 User’s and Service Guide

(included with the retrofit kit) for complete details on using the assembly.

Installing the Phase-Lock Assembly

1 Remove the outer cover from the Agilent 33120A.

Page 1

Agilent 33120A

Option 001 Phase-Lock Assembly

Installation Instructions for 33120-80001 Retrofit Kit

Loosen

Captive

Screws

Remove

Bottom Screw

Slide Off Outer Cover

2 Carefully cut two holes in the rear-panel label.

The Ref Out and Ext Ref In terminals on the Phase-Lock assembly will

extend through these holes in the 33120A rear-panel. Pierce the label in

the center of the chassis holes and then cut to the outer edge of the holes.

Then, let the chassis holes guide the knife around the edge of the hole.

3 Connect the coaxial cable to the Phase-Lock circuit board.

Connect one end of the coaxial cable (included with the retrofit kit) to

the connector labeled P2 on the Phase-Lock circuit board. Position the

cable as shown.

Cut Out Label

to Chassis Holes

Coaxial Cable (33120-61603)

4 Install the Phase-Lock assembly in the Agilent 33120A chassis.

Before installing the Phase-Lock assembly, make sure that the red and

black wires for the instrument fan are clear of the rear-panel holes.

With the Phase-Lock assembly positioned component side down,

insert the two BNC connectors through the holes previously cut in

the rear-panel label.

5 Secure the Phase-Lock assembly in place.

As shown above, place one lock washer and one hex nut (included with

the retrofit kit) on each of the two BNC connectors. To prevent cross-

threading, be sure to hand-tighten the hex nuts at least one turn before

using a tool.

Lock Washer (2190-0699)

Hex Nut (2940-0256)

Component Side

Down

Top View

Side View

6 Connect the coaxial cable to Agilent 33120A circuit board.

First, slide the black ferrite bead to the end of the coaxial cable as shown.

Then, connect the coaxial cable to connector J401 on the 33120A circuit

board. Be sure to position the cable away from the heatsinks on the

circuit board.

7 Connect the ribbon cable to the Agilent 33120A circuit board.

Connect the loose end of the grey ribbon cable to connector J102 on the

33120A circuit board. Press down firmly on the ribbon cable connector

and secure the cable in place with the locking clips.

Ferrite Bead

J401

Ribbon

Cable

J102

Snap the Locking Clips

over the top of the connector

to secure the Ribbon Cable.

Calibration /Adjustment Procedure

After installing the Phase-Lock assembly, perform the frequency

adjustment procedure (CAL:SETup 86) on page 69 in the Agilent

33120A Service Guide. Be sure to make the 10 MHz frequency

measurement with an accuracy of at least 8 digits (0.01 ppm). It may

be necessary to perform up to three iterations of the frequency

adjustment following the initial installation of the Phase-Lock assembly.

Installation of the Phase-Lock assembly requires that you perform

only the frequency adjustment (CAL:SETup 86) as outlined above,

no further calibration steps are required.

For complete details on performing a calibration, see chapter 4 in

the Agilent 33120A Service Guide.

If you intend to perform an entire calibration at the time you install the

Phase-Lock assembly or in the future, CAL:SETup 86 should replace

CAL:SETup 00 as the first step. You will have to manually change from

setup 00 to setup 86 for this. With “SETUP ^00” displayed on the front

panel, press the “Enter Number” key, the “8” key, the “6” key, and then

press the “Enter” key.

Note that while the instrument automatically steps through setup

numbers as you perform calibration steps, it does not automatically step

from setup 86 to setup 01 (the next calibration step). Therefore, after

performing the frequency calibration adjustment, the instrument will

display “SETUP ^86”. At this point, press the “Enter Number” key,

the “0” key, the “1” key, and then press the “Enter” key. This will return

you to the normal setup sequence starting with “SETUP ^01”.

Outside of Rear Cover



33120-90023

&RS\ULJKW$JLOHQW7HFKQRORJLHV,QF

3ULQWHGLQ0DOD\VLD

GLWLRQ

0DUFK 

Retrofit Instructions

Andere Handbücher für 33120A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Agilent Technologies Laborausrüstung Handbücher

Agilent Technologies

Agilent Technologies TS-8989 PXI Bedienungsanleitung

Agilent Technologies

Agilent Technologies G1289 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260Infinity II Bio-inert FractionCollector Bedienungsanleitung

Agilent Technologies

Agilent Technologies 280-DS MQS Bedienungsanleitung

Agilent Technologies

Agilent Technologies PR02 Bedienungsanleitung

Agilent Technologies

Agilent Technologies CrossLab CS Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7683 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6890 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies MP-AES Leitfaden

Agilent Technologies

Agilent Technologies 1260 Infinity II Quaternary System Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1100 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1290 infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5975 MSD Bedienungsanleitung

Agilent Technologies

Agilent Technologies 7100 Bedienungsanleitung

Agilent Technologies

Agilent Technologies Seahorse XFp Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5975 MSD Bedienungsanleitung

Agilent Technologies

Agilent Technologies Infinity Binary Pump VL 1290 Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5850A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1100 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity II Bedienungsanleitung

Agilent Technologies

Agilent Technologies G6011A Quiet Cover MS Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1260 Infinity Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5100 ICP-OES Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1220 Infinity II LC Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Yamato

Yamato BM510 Bedienungsanleitung