Agilent Technologies E4418B Bedienungsanleitung

Agilent Technologies

Agilent E4418B

Power Meter

User’s Guide

ii E4418B Power Meter User’s Guide

Notices

No part of this manual may be reproduced

in any form or by any means (including

electronic storage and retrieval or transla-

tion into a foreign language) without prior

agreement and written consent from Agi-

lent Technologies, Inc. as governed by

United States and international copyright

laws.

Manual Part Number

E4418-90032

Edition

Eighth Edition, April 5, 2013

Printed in Malaysia

Agilent Technologies, Inc.

3501 Stevens Creek Blvd.

Santa Clara, CA 95052 USA

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connec-

tion with the furnishing, use, or per-

formance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a

license and may be used or copied only in

accordance with the terms of such license.

Restricted Rights Legend

U.S. Government Restricted Rights. Soft-

ware and technical data rights granted to

the federal government include only those

rights customarily provided to end user cus-

tomers. Agilent provides this customary

commercial license in Software and techni-

cal data pursuant to FAR 12.211 (Technical

Data) and 12.212 (Computer Software) and,

for the Department of Defense, DFARS

252.227-7015 (Technical Data - Commercial

Items) and DFARS 227.7202-3 (Rights in

Commercial Computer Software or Com-

puter Software Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indi-

cated conditions are fully under-

stood and met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and

met.

E4418B Power Meter User’s Guide iii

Certification

Agilent Technologies certifies that this product met its published

specifications at the time of shipment from the factory. Agilent

Technologies further certifies that its calibration measurements are

traceable to the United States National Institute of Standards and

Technology, to the extent allowed by the Institute’s calibration facility and

to the calibration facilities of other International Standards Organization

members.

Warranty

This Agilent Technologies instrument product is warranted against defects

in material and workmanship for a period of 3 years from date of shipment.

During the warranty period, Agilent Technologies will at its option, either

repair or replace products which prove to be defective. For warranty

service or repair, this product must be returned to a service facility

designated by Agilent Technologies. Buyer shall prepay shipping charges

to Agilent Technologies and Agilent Technologies shall pay shipping

charges, duties and taxes for products returned to Aglent Technologies

from another country. Agilent Technologies warrants that its software and

firmware designated by Agilent Technologies for use with an instrument

will execute its programming instructions when properly installed on that

instrument. Agilent Technologies does not warrant that the operation of

the instrument or firmware will be uninterrupted or error free.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper

or inadequate maintenance by Buyer, Buyer-supplied software or

interfacing, unauthorized modification or misuse, operation outside of the

environmental specifications for the product or improper site preparation

or maintenance. NO OTHER WARRANTY IS EXPRESSED OR IMPLIED.

AGILENT TECHNOLOGIES SPECIFICALLY DISCLAIMS THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

iv E4418B Power Meter User’s Guide

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE BUYER’S SOLE AND EXCLUSIVE

REMEDIES. AGILENT TECHNOLOGIES SHALL NOT BE LIABLE FOR ANY

DIRECT, INDIRECT, SPECIAL, INCIDENTAL or CONSEQUENTIAL

DAMAGES, WHETHER BASED ON CONTRACT, TORT or ANY OTHER

LEGAL THEORY.

Warnings and Cautions

This guide uses warnings and cautions to denote hazards.

Recommended Calibration Interval

Agilent Technologies recommends a two- years calibration cycle for the

E4418B EPM Series power meter.

WARNING

A warning calls attention to a procedure, practice or the like, which, if

not correctly performed or adhered to, could result in injury or the loss of

life. Do not proceed beyond a warning until the indicated conditions are

fully understood and met.

CAUTION

A caution calls attention to a procedure, practice or the like which, if not

correctly performed or adhered to, could result in damage to or the

destruction of part or all of the equipment. Do not proceed beyond a

caution until the indicated conditions are fully understood and met.

E4418B Power Meter User’s Guide v

Safety Symbols

The following symbol on the instrument and in the documentation

indicates precautions that must be taken to maintain safe operation of the

instrument.

Caution, risk of danger.

The Instruction Documentation Symbol. The product is marked with this

symbol when it is necessary for the user to refer to the instructions in the

supplied documentation.

Alternating current (AC).

This symbol indicates the operating switch for ‘Stand-by’ mode. Note, the

instrument is NOT isolated from the mains when the switch is pressed.

To isolate the instrument, the mains coupler (mains input cord) should be

removed from the power supply.

This symbol indicates the operating switch for ‘On’ mode).

External Protective Earth Terminal.

While this is a Class I product, provided with a protective earthing

conductor in a power cord, an external protective earthing terminal has

also been provided. This terminal is for use where the earthing cannot be

assured. At least an 18AWG earthing conductor should be used in such

an instance, to ground the instrument to an assured earth terminal.

vi E4418B Power Meter User’s Guide

Personal Safety Considerations

This is a Safety Class I product (provided with a protective earthing ground

incorporated in the power cord). The mains plug shall only be inserted in a

socket outlet provided with a protective earth contact. Any interruption of

the protective conductor, inside or outside the instrument is likely to make

the instrument dangerous. Intentional interruption is prohibited

General Safety Considerations

WARNING

If this instrument is not used as specified, the protection provided by the

equipment could be impaired. This instrument must be used in a normal

condition (in which all means of protection are intact) only.

No operator serviceable parts inside. Refer servicing to qualified

personnel. To prevent electrical shock, do not remove covers.

For continued protection against fire hazard, replace the line fuse(s)

only with fuses of the same type and rating (for example, normal blow,

time delay, etc.). The use of other fuses or material is prohibited.

WARNING

Before this instrument is switched on, make sure it has been properly

grounded through the protective conductor of the ac power cable to a

socket outlet provided with protective earth contact.

Any interruption of the protective (grounding) conductor, inside or

outside the instrument or disconnection of the protective earth terminal

can result in personal injury.

CAUTION

Any adjustments or service procedures that require operation of the

instrument with protective covers removed should be performed only by

trained service personnel.

E4418B Power Meter User’s Guide vii

Regulatory Markings

The CE mark shows that the product complies with all the relevant

European legal Directives (if accompanied by a year, it signifies when the

design was proven.

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme à la norme NMB-001 du Canada.

This is the symbol of an Industrial Scientific and Medical Group 1 Class A

product.

The CSA mark is a registered trademark of the Canadian Standards

Association.

viii E4418B Power Meter User’s Guide

IEC 1010-1 Compliance

This instrument has been designed and tested in accordance with IEC

Publication 61010-1 +A1:1992 Safety Requirements for Electrical

Equipment for Measurement, Control and Laboratory Use and has been

supplied in a safe condition. The instruction documentation contains

information and warnings which must be followed by the user to ensure

safe operation and to maintain the instrument in a safe condition.

Statement of Compliance

This product has been designed and tested for compliance with IEC 60529

(1989) Degrees of Protection Provided by Enclosures (IP Code). Level IPx4

is attained if, and only if, the carry case( Agilent Technologies part number

34141A) is fitted.

User Environment

This product is designed for use in a sheltered environment (avoiding

extreme weather conditions) in accordance with Pollution Degree 3

defined in IEC 60664-1, with the carry case (Agilent Technologies part

number 34141A) fitted over the instrument.

The product is suitable for indoor use only, when this carry case is not

fitted.

Installation Instructions

To avoid unnecessary over-temperature conditions, while this carry case is

fitted do not apply an ac mains supply voltage, only operate your Agilent

Technologies E4418B from the battery pack.

E4418B Power Meter User’s Guide ix

Regulatory Information

Sound Emission

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der

Maschinenlarminformationsverordnung vom 18 Januar 1991.

• Sound Pressure LpA < 70 dB.

• Am Arbeitsplatz.

• Normaler Betrieb.

• Nach DIN 45635 T. 19 (Typprufung).

Manufacturers Declaration

This statement is provided to comply with the requirements of the German

Sound DIN 45635 T. 19 (Typprufung).

• Sound Pressure LpA < 70 dB.

• At operator position.

• Normal operation.

• According to ISO 7779 (Type Test).

Australian EMC Regulations

The C-Tick mark is a registered trademark of the Spectrum Management

Agency of Australia. This signifies compliance with the Australian EMC

Framework Regulations under the terms of the Radiocommunications Act

of 1992.

N279

x E4418B Power Meter User’s Guide

Declaration of Conformity (DoC)

The Declaration of Conformity (DoC) for this instrument is available on the

Web site. You can search the DoC by its product model or description.

http://regulations.corporate.agilent.com/DoC/search.htm

NOTE

If you are unable to search for the respective DoC, please contact your

local Agilent representative.

Andere Handbücher für E4418B

Inhaltsverzeichnis

Andere Agilent Technologies Messgerät Handbücher

Agilent Technologies

Agilent Technologies U1211A Bedienungsanleitung

Agilent Technologies

Agilent Technologies PSA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5080 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4352B Bedienungsanleitung

Agilent Technologies

Agilent Technologies X Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies Flow Tracker 1000 Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8362B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4100 Bedienungsanleitung

Agilent Technologies

Agilent Technologies MXA Series Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies E4440A Kurzanleitung

Agilent Technologies

Agilent Technologies Cary Eclipse Bedienungsanleitung

Agilent Technologies

Agilent Technologies U2722A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4263B Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 4396B Betriebsanleitung

Agilent Technologies

Agilent Technologies 4294A Bedienungsanleitung

Agilent Technologies

Agilent Technologies N2797A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83438A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4285A Bedienungsanleitung

Agilent Technologies

Agilent Technologies FieldFox N9913A Bedienungsanleitung

Agilent Technologies

Agilent Technologies X Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4991A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5185-5991 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 490 Micro GC Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8719ET Handbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung