Agilent Technologies E8362A PNA Series Kurzanleitung

Agilent Part Number: E8362-90016

Printed in USA September 2007

Supersedes print date: February 2005

Installation Note

Extended Frequency Range Upgrade Kit

For E8362A PNA Series Microwave Network Analyzers WITH the

Configurable Test Set Option

Network Analyzer

Model Number

Upgrade Kit

Part Number

Frequency

Extension

E8362A, Option 014 E8362-60105 20 GHz to 40 GHz

2Installation Note E8362-90016

WARRANTY STATEMENT

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO

BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM

EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION

CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. AGILENT SHALL NOT BE

LIABLE FOR ERRORS OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE FURNISHING, USE, OR PERFORMANCE OF THIS DOCUMENT OR

ANY INFORMATION CONTAINED HEREIN. SHOULD AGILENT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE

SEPARATE AGREEMENT WILL CONTROL.

DFARS/Restricted Rights Notice

If software is for use in the performance of a U.S. Government prime contract or subcontract,

Software is delivered and licensed as “Commercial computer software” as defined in DFAR

252.227-7014 (June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as

“Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use, duplication or disclosure of Software is subject to

Agilent Technologies’ standard commercial license terms, and non-DOD Departments and

Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in

FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than

Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any technical data.

Safety Notes

The following safety notes are used throughout this document. Familiarize yourself with each

of these notes and its meaning before performing any of the procedures in this document.

WARNING

Warning denotes a hazard. It calls attention to a procedure which,

if not correctly performed or adhered to, could result in injury or

loss of life. Do not proceed beyond a warning note until the

indicated conditions are fully understood and met.

CAUTION

Caution denotes a hazard. It calls attention to a procedure that, if not

correctly performed or adhered to, could result in damage to or destruction

of the instrument. Do not proceed beyond a caution sign until the indicated

conditions are fully understood and met.

Installation Note E8362-90016 3

Contacting Agilent

Assistance with test and measurements needs and information or finding a local Agilent office

are available on the Web at:

www.agilent.com/find/assist

If you do not have access to the Internet, please contact your Agilent field engineer.

NOTE

In any correspondence or telephone conversation, refer to the Agilent product by

its model number and full serial number. With this information, the Agilent

representative can determine whether your product is still within its warranty

period.

About the Upgrade Kit

IMPORTANT

Option 041 can only be installed on analyzers with Option 014, as listed

below as “Products affected”. If your analyzer does not have Option 014 (as

listed below), it will be necessary to install the option BEFORE installing

this option (Option 041).

If you need assistance, refer to “Contacting Agilent” on page 3.

Description of the Upgrade

This upgrade kit is used to extend the frequency range of the:

• E8362A, Option 014 PNA microwave network analyzer from 20 GHz to 40 GHz

Products affected. . . . . . . . . . . . . . . . . . . . . . . . . . E8362A with Option 014, Configurable

Test Set

Installation to be performed by . . . . . . . . . . . . . . Agilent service center or personnel

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 4 hours

Estimated adjustment time . . . . . . . . . . . . . . . . . 1 hour

Estimated full instrument calibration time . . . . 4.5 hours

4Installation Note E8362-90016

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any item is missing or damaged,

contact Agilent Technologies. Refer to “Contacting Agilent” on page 3.

Table 1 Option 041 Upgrade Kit (E8362-60105) to Extend the E8362A to 40 GHz

Ref.

Desig. Description Qty Part Number

Parts for ALL analyzers with Option 014 (with or without any other options)

N/A Installation note (this document) 1 E8362-90016

N/A License key certificate 1 5964-5136

N/A Model number nameplate (for 40 GHz analyzer, E8363A) 1 E8363-80001

A21 SOMA 50 1 5087-7130

A23 Channel R1 detector

2 5087-7133

A24 Channel R2 detector

A25 Test port 1 coupler

2 5087-7518

A26 Test port 2 coupler

A27 Channel A first converter (mixer) 2 5087-7122

A30 Channel B first converter (mixer)

N/A Machine screw M3.0 x 18 (for attaching A23 and A24 detectors) 4 0515-0666

N/A Machine screw M3.0 x 30 (for attaching SOMA 50) 4 0515-1349

N/A Ribbon cable, A21 SOMA 50 to A16 test set motherboard 1 8121-0818

N/A Cable, wrapped wire, detectors to A16 test set motherboard 2 E7340-60075

N/A Test set deck front panel 1 E8364-00014

W1 A12 source 20 to A21 SOMA 50 1 E8364-20036

W2 A21 SOMA 50 to A22 switch/splitter 1 E8364-20034

W3 A22 switch/splitter to A23 channel R1 detector 1 E8364-20023

W4 A22 switch/splitter to A24 channel R2 detector 1 E8364-20024

W37 A23 channel R1 detector to A16 test set motherboard J204 1 E8364-60121

W38 A24 channel R2 detector to A16 test set motherboard J205 1 E8364-60122

W39 A21 SOMA 50 to A16 test set motherboard J206 1 E8364-60123

W65 A23 channel R1 detector to REFERENCE 1 SOURCE OUT 1 E8364-20047

W66 A24 channel R2 detector to REFERENCE 2 SOURCE OUT 1 E8364-20048

W67 A25 test port 1 coupler to PORT 1 CPLR ARM 1 E8364-20043

W68 A26 test port 2 coupler to PORT 2 CPLR ARM 1 E8364-20044

W69 PORT 1 RCVR A IN to A27 channel A mixer 1 E8364-20045

W72 PORT 2 RCVR B IN to A30 channel B mixer 1 E8364-20046

W60 Front-panel jumper 6 E8364-20059

Installation Note E8362-90016 5

Parts for analyzers with Option 014 ONLY

W61 A22 switch splitter to PORT 1 SOURCE OUT 1 E8364-20081

W62 A22 switch splitter to PORT 2 SOURCE OUT 1 E8364-20082

W63 PORT 1 CPLR THRU to A25 test port 1 coupler 1 E8364-20073

W64 PORT 2 CPLR THRU to A26 test port 2 coupler 1 E8364-20074

W70 REFERENCE 1 RCVR R2 IN to A28 channel R1 mixer 1 E8364-20075

W71 REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer 1 E8364-20076

Parts for analyzers with Options 014 AND UNL

A38 Port 1 bias tee

2 5087-7233

A39 Port 2 bias tee

W70 REFERENCE 1 RCVR R2 IN to A28 channel R1 mixer 1 E8364-20049

W71 REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer 1 E8364-20050

W81 A36 port 1 step attenuator to PORT 1 SOURCE OUT 1 E8364-20053

W82 A37 port 2 step attenuator to PORT 2 SOURCE OUT 1 E8364-20054

W83 PORT 1 CPLR THRU to A38 port 1 bias tee 1 E8364-20039

W84 PORT 2 CPLR THRU to A39 port 2 bias tee 1 E8364-20040

Table 1 Option 041 Upgrade Kit (E8362-60105) to Extend the E8362A to 40 GHz

Ref.

Desig. Description Qty Part Number

6Installation Note E8362-90016

Installation Procedure for the Upgrade Kit

The network analyzer must be in proper working condition prior to installing this option. Any

necessary repairs must be made before proceeding with this installation.

WARNING

This installation requires the removal of the analyzer’s protective outer

covers. The analyzer must be powered down and disconnected from the

mains supply before performing this procedure.

Electrostatic Discharge Protection

Protection against electrostatic discharge (ESD) is essential while removing or connecting

cables or assemblies within the network analyzer.

Static electricity can build up on your body and can easily damage sensitive internal circuit

elements when discharged. Static discharges too small to be felt can cause permanent

damage. To prevent damage to the instrument:

•always wear a grounded wrist strap having a 1 MΩresistor in series with it when handling

components and assemblies.

•always use a grounded, conductive table mat while working on the instrument.

•always wear a heel strap when working in an area with a conductive floor. If you are

uncertain about the conductivity of your floor, wear a heel strap.

•always ground yourself before you clean, inspect, or make a connection to a static-sensitive

device or test port. You can, for example, grasp the grounded outer shell of the test port or

cable connector briefly.

Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to

“Tools Required for the Installation” on page 7 for part numbers.

Figure 1 ESD Protection Setup

Installation Note E8362-90016 7

Overview of the Installation Procedure

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Step 2. Remove the Outer Cover

Step 3. Remove the Inner Cover

Step 4. Remove the Front Panel Assembly

Step 5. Disconnect the A12 Source 20 to A22 Switch/Splitter Cable at the A12 Source 20

Step 6. Raise the Receiver Deck

Step 7. Remove the Old Hardware and Cables

Step 8. Replace the A38 and A39 Bias Tees (Option UNL Only)

Step 9. Install the Remaining New Hardware

Step 10. Install the Remaining Cables

Step 11. Lower the Receiver Deck

Step 12. Connect the A12 Source 20 to A21 SOMA 50 Cable at the A12 Source 20

Step 13. Replace the Front Panel Nameplate

Step 14. Reinstall the Front Panel Assembly and Front Panel Jumpers

Step 15. Reinstall the Inner and Outer Covers

Step 16. Enter the New Model Number

Step 17. Perform Post-Upgrade Adjustments and Calibration

Tools Required for the Installation

Description Agilent Part Number

T-8 TORX driver (set to 5 in-lbs) N/A

T-10 TORX driver (set to 9 in-lbs) N/A

T-20 TORX driver (set to 21 in-lbs) N/A

5/16-inch torque wrench (set to 10 in-lbs)a

a. Use a 5/16-inch torque wrench set to 10 in-lbs for all cable connections except the hex nuts on

the front-panel bulkhead connectors to which the front-panel jumpers attach. Use a 5/16-inch

torque wrench set to 21 in-lbs for these.

N/A

5/16-inch torque wrench (set to 21 in-lbs)aN/A

1-inch torque wrench (set to 72 in-lbs) N/A

8Installation Note E8362-90016

ESD Equipment and Supplies Required for the Installation

Equipment Required for Post-Upgrade Adjustments

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Refer to the License Key Certificate supplied with the kit:

• Verify that the analyzer’s model and serial numbers match those on the certificate.

• Verify that the option number on the certificate matches the option described by this

installation note.

If the model, serial, or option number do not match the expected results, you will not be able

to install the option. If this is the case, contact Agilent for assistance. Refer to “Contacting

Agilent” on page 3.

Description Agilent Part Number

ESD grounding wrist strap 9300-1367

5-ft grounding cord for wrist strap 9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire 9300-0797

ESD heel strap (for use with conductive floors) 9300-1308

Equipment Type Model or

Part Number

Alternate Model or

Part Number

Power meter E4418B/E4419B E4418A/E4419A

Power sensor, 2.4 mm 8487A None

Adapter, 2.4 mm (f) to 2.4 mm (f) 11900B 85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f) 85133C 85133E

Installation Note E8362-90016 9

Step 2. Remove the Outer Cover

CAUTION

This procedure is best performed with the analyzer resting on its front

handles in the vertical position. Do not place the analyzer on its front panel

without the handles. This will damage the front panel assemblies.

1. Disconnect the power cord (if it has not already been disconnected).

2. Using a T-20 TORX driver, remove the strap handles (item ④) by loosening the screws

(item ⑤) on both ends until the handle is free of the analyzer.

3. Using a T-20 TORX driver, remove the four rear panel feet (item ①) by removing the center

screws (item ②).

4. Slide the four bottom feet (item ③) off the cover.

5. Slide the cover off of the frame.

Figure 2 Outer Cover Removal

10 Installation Note E8362-90016

Step 3. Remove the Inner Cover

1. Place the analyzer top-side up on a flat surface.

2. Using a T-10 TORX driver, remove the eleven screws (item ①).

3. Lift off the cover.

Figure 3 Inner Cover Removal

Inhaltsverzeichnis

Andere Agilent Technologies Messgerät Handbücher

Agilent Technologies

Agilent Technologies U3025AE10 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 16902A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4155B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8510XF Service-Handbuch

Agilent Technologies

Agilent Technologies OmniBER 718 SDH Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8757D Bedienungsanleitung

Agilent Technologies

Agilent Technologies 35670A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8753ET Bedienungsanleitung

Agilent Technologies

Agilent Technologies N7745A Bedienungsanleitung

Agilent Technologies

Agilent Technologies WireScope 350 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8590 Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies E5900B Bedienungsanleitung

Agilent Technologies

Agilent Technologies 85225F Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8590L Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1271A Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1731B Handbuch

Agilent Technologies

Agilent Technologies 4284A Bedienungsanleitung

Agilent Technologies

Agilent Technologies FieldFox N9913A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 83438A Bedienungsanleitung

Agilent Technologies

Agilent Technologies NFA Series Gebrauchs- und Pflegehandbuch

Agilent Technologies

Agilent Technologies 4352B Bedienungsanleitung

Agilent Technologies

Agilent Technologies Cary 60 Bedienungsanleitung

Agilent Technologies

Agilent Technologies U2722A Bedienungsanleitung

Agilent Technologies

Agilent Technologies N1913a Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung