Agilent Technologies ICP-MS Series Betriebsanleitung

Agilent ICP-MS

Interactive Troubleshooting tool for

Plasma ignition problem

Next >

Rev. B

2017, January, 20

Preconditions

•7900, 7800, 7700, 8800, or 8900 ICP-MS is used.

•Sample introduction type is “PeriPump”. If you are using a special configuration such as

LC/GC integration or ISIS, setup the instrument with standard configuration.

•You have the “Hardware Maintenance Manual”for your instrument. Some details of the

operations are not in this tool. You should refer to the manual.

<Previous Next >

Legends

Notes or tips that help troubleshoot.

You need to refer to another document for detail of the steps.

Good example of situation.

Bad example of situation.

Did the ion lens test pass? ←Questions are displayed in blue you need to click

buttons such as or

Based on your answer the tool will navigate you to next step.

Note

Reference

Good

Bad

<Previous Next >

Yes No

1.1.1 Check Water flow and Gas flow errors

(1) Select MassHunter Instrument Control Window → Main menu → “View” → “Instrument

Status” to display “Instrument Status” Pane

If Main menu is not displayed, press F10 key.

(2) Click the dropdown below and check the error number for errors that are generated at the

date/time of the attempt to ignite plasma.

(3) Are error numbers 1440, 1445, or 1446 included in the latest errors?

Note

<Previous Yes No

1.2.1 Check water and argon gas

(1) If error 1440 has been generated, check if cooling water valve is open and chiller or heat

exchanger is working correctly.

(2) If error 1445 or 1446 have been generated, check if argon gas valve is open and remaining

amount is enough.

(3) Did this solve the problem？

Yes No

1.3.1 Check timing when Plasma goes out

(1) When did Plasma go out?

Not ignite at all

Several seconds after ignition

One to several minutes after ignition

When "Plasma Correction“ is going on

20 minutes or later after ignition

2.1.1 Check condition of argon gas line condition

(1) Are there any situations below?

-Ar cylinder has been replaced recently

-Was there any work on Ar line recently?

-Is the instrument used after a long time ( > 1 month).

Yes No

2.2.1 Check condition of argon gas line

(1) Purge Ar line.

(2) Do leak check on Ar line.

(3) Check specification of Ar gas to have ≧99.99% purity (In case cylinder has been replaced).

(4) Try alternative source of Ar gas (In case cylinder has been replaced and any alternatives

are available)

(5) Does this fix the problem?

Yes No

2.3.1 Isolate the torch and try to ignite

(1) Block end of the torch with plastic film and try to ignite.

(2) Can it ignite?

Yes No

2.4.1 Check torch box

(1) Open the torch box and observe to check if there are situations below, following

instruction from the next page.

- Damaged torch

- Damaged bonnet

- Damaged shield plate

- Damaged shield contact

-Non Agilent torch

-Dirty torch stand

-Wrongly assembled torch

<Previous Next >

Dieses Handbuch passt für folgende Modelle

5

Inhaltsverzeichnis

Andere Agilent Technologies Messgerät Handbücher

Agilent Technologies

Agilent Technologies ADM2000 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34136A Bedienungsanleitung

Agilent Technologies

Agilent Technologies Agilent 8163A Betriebsanleitung

Agilent Technologies

Agilent Technologies 71612 Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1211A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 35670A Bedienungsanleitung

Agilent Technologies

Agilent Technologies ESA-E E4407B Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies 55B AA Bedienungsanleitung

Agilent Technologies

Agilent Technologies HP 16500B Bedienungsanleitung

Agilent Technologies

Agilent Technologies AA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies ENA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies PNA Series Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies U2722A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4263B Bedienungsanleitung

Agilent Technologies

Agilent Technologies E4419B Bedienungsanleitung

Agilent Technologies

Agilent Technologies PSA Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 4286A Bedienungsanleitung

Agilent Technologies

Agilent Technologies 54600-Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies U1701A Bedienungsanleitung

Agilent Technologies

Agilent Technologies PSA Series Installations- und Betriebshandbuch

Agilent Technologies

Agilent Technologies U1731C Bedienungsanleitung

Agilent Technologies

Agilent Technologies 1290 Infinity II Bedienungsanleitung

Agilent Technologies

Agilent Technologies N2771A Bedienungsanleitung

Agilent Technologies

Agilent Technologies E8356A Installations- und Betriebshandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung