Albatron K8SLI-AM2 Bedienungsanleitung

K8SLI-AM2

All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed,

stored in a retrieval system or translated into any language or computer language, in any form

or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise,

without the prior written permission of the company. Brands and product names are trademarks

or registered trademarks of their respective companies.

The vendor makes no representations or warranties with respect to the contents herein and

especially disclaim any implied warranties of merchantability or fitness for any purpose. Further

the vendor reserves the right to revise this publication and to make changes to the contents

herein without obligation to notify any party beforehand. Duplication of this publication, in part or

in whole, is not allowed without first obtaining the vendor’s approval in writing.

Trademark

All the trademarks or brands in this document are registered by their respective owner.

Disclaimer

We make no warranty of any kind with regard to the content of this user’s manual. The content

is subject to change without notice and we will not be responsible for any mistakes found in this

user’s manual. All the brand and product names are trademarks of their respective companies.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense. However, there is no guarantee that

interference will not occur in a particular installation.

CE Mark

The device is in accordance with 89/336 ECC-ENC Directive.

Ver: EG100

K8SLI-AM2

nVIDIA®nForce4 SLI

Supports Socket AM2

AMD®AthlonTM 64 FX/ AthlonTM 64 x2 Dual-Core/

AthlonTM 64/ SempronTM Processor

User Manual

Dimensions (ATX Form-Factor):

244 mm x 305 mm ( W x L )

Operating System:

Windows® 2000/ XP

Attention- Im

ortant Information

Follow the procedures below…

Troubleshooting Tips

Refer to other sections in this manual…

Things You Should Know

The images and pictures in this manual are for reference only and may vary from the

product you received depending on specific hardware models, third party

components and software versions.

This mainboard contains very delicate IC chips. Always use a grounded wrist strap

when working with the system.

Do not touch any IC chip, lead, connector or other components.

Always unplug the AC power when you install or remove any device on the mainboard

or when confuguring pins and switches.

Packing List

K8SLI-AM2 mainboard

FDC Cable

HDD Cable

I/O Bracket

Serial ATA Cable

K8SLI-AM2 Mainboard User Manual CD

K8SLI-AM2 Setup Driver CD

K8SLI-AM2 Mainboard Quick Installation Guide

Symbols

Table of Contents

CHAPTER 1. GETTING STARTED ..................................................................1

INTRODUCTION....................................................................................................... 1

SPECIFICATION ....................................................................................................... 2

CONFIGURATION .................................................................................................... 5

Layout of K8SLI-AM2.................................................................................... 5

HARDWARE INSTALLATION ................................................................................... 6

CPU Processor Installation.............................................................................. 6

Memory Installation: DIMM1/2/3/4................................................................ 7

Back Panel Configuration................................................................................ 9

Connectors..................................................................................................... 11

Front Panel Headers: JW_FP, PWRLED, SPEAK ........................................ 12

Headers & Jumpers........................................................................................ 14

Audio Configuration...................................................................................... 16

Slots ............................................................................................................... 16

Power Supply Attachments............................................................................ 18

CHAPTER 2. BIOS SETUP............................................................................ 19

INTRODUCTION..................................................................................................... 19

KEY FUNCTION..................................................................................................... 19

MAIN MENU ......................................................................................................... 20

CHAPTER 3: SOFTWARE SETUP ............................................................... 22

SOFTWARE LIST ................................................................................................... 22

SOFTWARE INSTALLATION ................................................................................... 22

CHAPTER 4: TROUBLESHOOTING ............................................................ 25

APPENDIX I: 8/6/4/2 CHANNEL SETUP.................................................................. 28

APPENDIX II: RAID SETUP................................................................................... 29

APPENDIX III: SLI (SCALABLE LINK INTERFACE)................................................ 30

Mainboard K8SLI-AM2

Chapter 1. Getting Started

Introduction

Congratulations on choosing the K8SLI-AM2 Mainboard. It is based on the nVIDIA®nForce4

SLI chipset. The mainboard supports the AMD AthlonTM 64 FX/ AthlonTM 64 X2 Dual-Core/

AthlonTM 64/ SempronTM Processor with FSB (Front Side Bus) frequencies of 1000 MHz (2000

MT/s).

The K8SLI-AM2 provides four DIMM (Dual In-Line Memory Modules) sockets and which with

Dual Channel Technology supported. The sockets allow you to install 240-pin, non-ECC &

unbuffered DDR II 800 (PC2-6400)/ DDR II 667 (PC2-5300)/ DDR II 533 (PC2-4300)/ DDR II

400 (PC2-3200) SDRAM, and support a total memory capacity of 8GB.

This mainboard provides one PCI-E x16 slot for use with a graphics card. It also provides two

PCI-E x8 slots which can be used with two identical SLI-ready PCI-Express graphics cards,

enabling SLI Technology and significantly increasing graphics performance <See Appendix III>.

There is also one PCI-E x1 slot provided for use with a PCI-E x1 compatible expansion card.

Three standard PCI slots for use with standard PCI expansion cards are also allowed.

The K8SLI-AM2 provides one floppy disk drive connector that can be used with 360KB/ 720KB/

1.2MB/ 1.44MB/ 2.88MB drive. It also has two IDE connectors for hard drives supporting Ultra

ATA 133/ 100/ 66/ 33 IDE devices. In addition, the onboard Serial ATA II comes with four SATA

II connectors, which the interface can provide up to 3 Gb/s transmit speed and also support

RAID 0/ 1/ 0+1 mode <See Appendix II>.

The onboard AC’ 97 Audio CODEC (ALC850) supports 8/6/4/2 channel audio play <See

Appendix I>. The mainboard also supports the Sony/Philips Digital Interfaces (SPDIF)

output/input function.

The K8SLI-AM2 also comes with an onboard 10/100/1000 Mbps Ethernet LAN PHY. There is a

LAN port on the back panel of your case that you can directly plug into an internet cable.

In addition, there are maximal ten USB2.0/ 1.1 ports which can be set up on this mainboard.

All the information (including hardware installation and software installation) in this manual are

for reference only. The contents in this manual may be updated without notice. The company

will not assume any responsibility for any errors or mistakes within.

Mainboard K8SLI-AM2

Specification

CPU:

Supports Socket AM2

Supports AMD AthlonTM 64 FX/ AthlonTM 64 x2 Dual-Core/ AthlonTM 64/ SempronTM

Processor

Supports Hyper-TransportTM Link Technology

Supports 1000 MHz (2000MT/s) FSB (Front Side Bus) Frequencies

Chipset:

Chipset – nVIDIA®nForce4 SLI

I/O Controller – Fintek®F71872FG

AC’ 97 Aduio Codec – Realtek®ALC850

LAN PHY – Marvell®88E1115 10/100/1000 LAN PHY

Memory:

Four DIMM sockets with Dual Channel Technology supported

Supports a total memory capacity of 8GB

Supports to use the 240-pin, non-ECC & unbuffered DDR II 800 (PC2-6400)/ DDR II

667 (PC2-5300)/ DDR II 533 (PC2-4300)/ DDR II 400 (PC2-3200) SDRAM

Slots:

Four PCI-Express interface slots for graphics cards and expansion cards:

1. One PCI-E x16 slot: supports up to x16 mode with 4 GB/s one-way bandwidth

2. Two PCI-E x8 slots: supports up to x8 mode with 2 GB/s one-way bandwidth

3. One PCI-E x1 slot: supports up to x16 mode with 250 MB/s one-way bandwidth

Three PCI slots with 133 MB/s one-way bandwidth per channel for expansion cards

FDD Connector:

One floppy disk drive connector supporting up to two FDDs

Supports 360KB/ 720KB/ 1.2MB/ 1.44MB/ 2.88MB

Onboard IDE Connector:

Two IDE connectors that support up to four IDE devices

Mainboard K8SLI-AM2

Supports Ultra ATA 133/ 100/ 66/ 33

Supports high capacity hard disk drives

Serial ATA II Connector:

Four SATA II connectors that support up to four SATA II HDDs

Supports SATA 2.0 specification which provides 3 Gb/s transmit rate

Supports RAID 0/1/ 0+1 mode

I/O facility Connectors:

One multi-mode Parallel Port is capable to support as the following:

1. Standard & Bi-direction Parallel Port

2. Enhanced Parallel Port (EPP)

3. Extended Capabilities Port (ECP)

Supports one PS/2 mouse port and one PS/2 keyboard port

Supports one serial port（COM1）on back panel

Supports one SPDIF IN port and one SPDIF OUT port on back panel

Supports one IrDA（IR）header with external device connected

Universal Serial Bus:

Four onboard USB 2.0/ 1.1 ports

Three front USB headers come with this mainboard supporting six additional USB

ports to be set

Supports a maximum of ten USB 2.0/ 1.1 ports for compliant devices

Onboard AC’ 97 Sound CODEC (ALC850):

High performance CODEC with high S/N ratio (>90 db)

Compliant with AC’ 97 2.3 specification

Supports 8/6/4/2 channel playback capability

Support 3D stereo enhancement

Supports jack sensing and re-tasking function

Support Sony/ Philips Digital Interfaces (S/PDIF) functionality

Onboard LAN Chip:

Mainboard K8SLI-AM2

Supports 10/100/1000 Mbps Ethernet LAN

Supports nVIDIA®Active Armor TM, it provides advanced data packet inspection

Supports nVIDIA® Firewall TM, it protects your system from intruders

BIOS:

Phoenix-Award™ BIOS

Supports APM 1.2

Supports ACPI 2.0 power management

Green Function:

Supports Phoenix-Award™ BIOS power management function

Supports system-wake-from-power-saving-mode by keyboard or mouse touching

Shadow RAM:

Integrated memory controller provides shadow RAM functionality and supports ROM

BIOS

Flash Memory:

Supports flash memory functionality

Supports ESCD functionality

Hardware Monitor Function:

Monitors CPU/ Chassis Fan Speed

Monitors CPU and system temperatures

Monitors system voltages

Mainboard K8SLI-AM2

Configuration

Layout of K8SLI-AM2

Mainboard K8SLI-AM2

Hardware Installation

This section will assist you in quickly installing your system hardware. Wear a wrist ground strap

before handling components. Electrostatic discharge may damage your system components.

CPU Processor Installation

This mainboard supports AMD AthlonTM 64 FX/ AthlonTM 64 x2 Dual-Core/ AthlonTM 64/

SempronTM processor and uses a Socket AM2. Before building your system, we suggest you

visit the AMD website and review the processor installation procedures. http://www.amd.com

CPU Socket AM2 Configuration Steps:

Locate the CPU socket on your mainboard and nudge the locking lever away from the socket.

Then lift the lever to a 90-degree angle.

On the socket, locate the corner which has the “diagonally cut-corner” on the rectangular

shaped pattern of pinholes (see diagram below-left). Match that corner with the “gold triangle”

on the CPU (see diagram below-right) and lower the CPU onto the socket. The bottom of the

CPU should be flush with the face of the socket.

Lower the lever until it snaps back into position. This will lock down the CPU.

Smear thermal grease on top of the CPU. Lower the CPU fan onto the CPU and use the clasps

on the fan to attach it to the socket. Finally, extend the power cable from the fan and insert it

onto the “CPUFAN” adapter.

ttention

DO NOT touch the CPU pins in case they are damaged. Also, make sure

that you have completed all installation steps before powered on the

system. Finally, double-check that the cooling fan is properly installed and

the CPU fan power cord is securely attached, in case your CPU and other

sensitive components are damaged because of high temperatures.

Inhaltsverzeichnis

Andere Albatron Hauptplatine Handbücher

Albatron

Albatron PX865PEC PRO Bedienungsanleitung

Albatron

Albatron PM945GC Bedienungsanleitung

Albatron

Albatron PX865PE7 Bedienungsanleitung

Albatron

Albatron PX865PE PRO II Bedienungsanleitung

Albatron

Albatron K8X890 Series Bedienungsanleitung

Albatron

Albatron KX400+ Pro-C Bedienungsanleitung

Albatron

Albatron PXP43 Bedienungsanleitung

Albatron

Albatron PX915PC PRO-G Bedienungsanleitung

Albatron

Albatron PXP35 Bedienungsanleitung

Albatron

Albatron KM400T-8X Pro Bedienungsanleitung

Albatron

Albatron PI945GSE-270 Bedienungsanleitung

Albatron

Albatron KX550 Bedienungsanleitung

Albatron

Albatron PXP45 Bedienungsanleitung

Albatron

Albatron PX915P-2V Bedienungsanleitung

Albatron

Albatron KX520LE Bedienungsanleitung

Albatron

Albatron K8SLI Bedienungsanleitung

Albatron

Albatron PXP965 (V2.0) Bedienungsanleitung

Albatron

Albatron PM800 Pro (V2.0) Bedienungsanleitung

Albatron

Albatron K8NF4 Series Bedienungsanleitung

Albatron

Albatron PX915P4 Series Bedienungsanleitung

Albatron

Albatron K8X250 Bedienungsanleitung

Albatron

Albatron PX915PD Series Bedienungsanleitung

Albatron

Albatron P4M800-775 Bedienungsanleitung

Albatron

Albatron PX915-DV Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung