Allen-Bradley ArmorPoint DeviceNet 1738-ADN12 Bedienungsanleitung

ArmorPoint I/O

DeviceNet

Adapters

1738-ADN12, 1738-ADN18,

1738-ADN18P, 1738-ADNX

User Manual

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application,

Installation and Maintenance of Solid State Controls (Publication SGI-1.1

available from your local Rockwell Automation sales office or online at

http://www.ab.com/manuals/gi) describes some important differences

between solid state equipment and hard-wired electromechanical devices.

Because of this difference, and also because of the wide variety of uses for

solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is

acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for

indirect or consequential damages resulting from the use or application of

this equipment.

The examples and diagrams in this manual are included solely for illustrative

purposes. Because of the many variables and requirements associated with

any particular installation, Rockwell Automation, Inc. cannot assume

responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to

use of information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without

written permission of Rockwell Automation, Inc. is prohibited.

Throughout this manual, when necessary we use notes to make you aware of

safety considerations.

WARNING Identifies information about practices or circumstances

that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful

application and understanding of the product.

ATTENTION Identifies information about practices or circumstances

that can lead to personal injury or death, property

damage, or economic loss. Attentions help you:

•identify a hazard

•avoid a hazard

•recognize the consequence

SHOCK HAZARD

Labels may be located on or inside the equipment (e.g.,

drive or motor) to alert people that dangerous voltage may

be present.

BURN HAZARD Labels may be located on or inside the equipment (e.g.,

drive or motor) to alert people that surfaces may be

dangerous temperatures.

1Publication 1738-UM001A-EN-P - February 2005

Preface

Purpose of This Manual

This manual describes how to install, configure, and operate your

ArmorPoint I/O™ DeviceNet™ Adapters, catalog numbers

1738-ADN12, -ADN18, -ADN18P, and -ADNX.

Who Should Use

This Manual

You must be able to use RSNetWorx for DeviceNet™ software or a

similar configuration software to configure your adapter.

In this manual, we assume you know how to configure an adapter. If

you do not, refer to your software user manuals or online help before

attempting to use these adapters.

We also assume you are familiar with the ArmorPoint I/O product

line, including other fieldbus interfaces, I/O modules, and power

supplies. If you are not familiar with these components, you can read

some of the ArmorPoint I/O documents listed in the Related Products

and Documentation section.

See the following sections: Page:

Who Should Use This Manual P-2

What the Manual Contains P-2

Related Terms P-3

Related Products and Documentation P-5

Guidelines for Using Your Adapter P-6

Conventions Used in This Manual P-6

IMPORTANT In this manual, we use ArmorPoint DeviceNet

adapters to refer to all the 1738 DeviceNet adapter

modules (1738-ADN12, -ADN18, -ADN18P, and

-ADNX). We use the specific catalog number (e.g.,

1738-ADNX) to refer to a specific module.

In the rest of this manual (except Chapter 4), we

refer to the ArmorPoint I/O DeviceNet adapters as

the adapters.

In Chapter 4, we refer to the ArmorPoint I/O

DeviceNet adapter as the scanner because the

chapter describes how to configure the adapter on

the subnet.

Publication 1738-UM001A-EN-P - February 2005

Preface 2

What the Manual Contains

This manual contains the following sections:

1738-ADN12

DeviceNet In

DeviceNet Out

X10

Adapter

Status

DeviceNet

Status

PointBus

Status

System

Power

Adapter

Power

PWR

Chapter 2 - What Is the ArmorPoint DeviceNet Adapter?

Overview of the adapter’s features and functionality

Chapter 1 - Install the ArmorPoint DeviceNet Adapters

Description of how to install and wire the adapter

Chapter 3 - Use Auto Start Mode

Description of how to use the Auto

StartModeonyouradaptertoquickly

get your system up and running

Chapter 4 - Configure the

DeviceNet Scanner Subnet

Description of how to configure your

adapter on the subnet

Chapter 5 - Add the ArmorPoint

DeviceNet Adapter to the DeviceNet

Scanner’s Scanlist

Description of how to configure the

DeviceNet adapter and how to add it tothe

scanlist

Appendix A - Specifications

Listing of the ArmorPoint adapters’

specifications

Chapter 6 - Troubleshoot the

ArmorPoint DeviceNet Adapter

Description of how to use the status

indicators and how to troubleshoot your

adapter

Appendix B - Quick Start

Learning how to use the 1738-ADN12

with a ControlLogix system on DeviceNet

Appendix C - 1738-ADNX Rules and Guidelines

Rules and guidelines regarding how to use the

1738-ADNX

Appendix D - Default Data Maps

Listing of the default data maps for

1738 ArmorPoint I/O modules

Publication 1738-UM001A-EN-P - February 2005

Preface 3

Related Terms

This manual uses the following terms:

Term: Definition:

Adapter The adapter interfaces between DeviceNet devices and

ArmorPoint I/O modules. ArmorPoint I/O DeviceNet adapters

include the 1738-ADN12, -ADN18, -ADN18P, and -ADNX.

Auto Catalog Replace The ArmorPoint I/ODeviceNet adapter supportsthe swapping

oftwoidenticalmodulesconnectedtotheadapter.Thatis,ifa

1738-IB4M12isinslot 3andanother1738-IB4M12is inslot7,

the two modules can be removed from the ArmorPoint system

andthe slot3 moduleplacedinto slot7,andvice-versa.When

Automatic Device Replacement (ADR) is active, the swapped

modules will be reconfigured to match the previous modulein

their new slot. When ADR is not active, the configuration

parameters will not be modified, the swapped modules must

have identical configuration and values for their EDS file

parameters.

Auto Device Replacement

(ADR) This refers to the ADR feature of a ControlLogix System on

DeviceNet.With ADRactive, anydeviceon theDeviceNet link

may be removed and replaced with an out-of-the-box

checkmark compliant DeviceNet device. The ADR feature will

result in downloading the values of the configuration

parameters of the EDS file of the removed device to the new

device.

Auto Start Mode A feature that lets the ArmorPoint I/O system get “up and

running” without the prerequisite to configure any of the EDS

parameters for the PointBus™or ArmorPoint I/O modules.

Using Auto Start Mode will result in a scan list within the

adapter that stores the modules identity information.

Autobaud A feature in devices (e.g., ArmorPoint I/O modules) on the

DeviceNet network that causes them to listen to

communicationson thenetwork andsettheirownbaudrateto

match the network rate.

Backplane The PointBus that consists of ArmorPoint I/O modules

connected to the ArmorPoint DeviceNet adapter.

Baudrate Rate of communications between devices on the DeviceNet

network. Backplane baudrate is used for the 1738-ADN12,

-ADN18, and -ADN18P. Subnet baudrate is used for the

1738-ADNX.

Change of State (COS) DeviceNet communications method in which the adapter

sends data based on detection of any changed value within

the input data. Data is independently received based on a

changeofstatefromthesender.Datainbothdirectionscanbe

acknowledged or unacknowledged depending on the run-time

configuration of the system.

Commissioning The period in time associated with post startup activities.

Commissioning implies that the system has been validated

and all configuration parameters are correct, all modules are

in good operating condition, and the adapter scanlist is

complete.

ControlFlash™ Utility software you can use to update the adapter’s firmware

with the most current boot and application code.

Publication 1738-UM001A-EN-P - February 2005

Preface 4

Cyclic DeviceNet communications method in which the adapter

sendsdatacyclicallybasedonaconfiguredtimevalue.Datais

independentlyreceivedcyclicallyfromthesender.Datainboth

directions can be acknowledged or unacknowledged

depending on the run time configuration of the system.

MACID Media Access Control Identifier (DeviceNet network address).

Master A DeviceNet network device (e.g., 1771-SDN) that initiates

communication with DeviceNet slave devices (e.g.,

ArmorPoint I/O modules) to retrieve data. The master only

receives unprompted data when the slave is enabled for COS

and there is a change in the device’s operating state.

Max Backplane MACID The 1738-ADNX has a unique attribute, Max(imum)

Backplane MACID. This value represents the highest node

address of a module residing on the backplane. This value

must be greater than or equal to the right most backplane

ArmorPoint I/O module, but must be less than that of any

non-backplane Subnet module.

Offline State of the adapter when it is not powered or maintaining

normal communication exchanges with other DeviceNet

devices.

Online State of the adapter when it is powered and maintaining

normal communication exchanges with other DeviceNet

devices.

PointBus The ArmorPoint I/O backplane PointBus maintains all

DeviceNet network protocol but also offers configuration

capabilities.

Polled DeviceNet communications method in which a module sends

data in response to received data.

Primary Network The primary DeviceNet network is defined as the DeviceNet

link that provides the direct connection between the

ArmorPoint DeviceNet adapter and a DeviceNet scanner.

RSNetWorxfor DeviceNet Configuration software for the adapter and Subnet modules.

Scanlist The list of Subnet modules connected to the adapter. When

ADR is active, the scanlist stores the configured values of

each of the Subnet modules’ configurable parameters. When

ADR is not active, the scanlist stores only the module identity

information.

Scanner Operating state of the ArmorPoint DeviceNet adapter when it

retrieves I/O data from Subnet modules.

Slave A DeviceNet network device that cannot initiate

communication (except when configured with COS enabled)

but responds to a DeviceNet master device.

Strobe Adapter sends data in response to the strobe command. The

singlebitallocatedtotheadapterinthestrobemessageis not

used. If the configured size of the input data (sent from the

adapter) is greater than 8 bytes, the strobe connection

establishment will fail. In this case, the input size must be

reconfigure to 8 bytes or less.

Term: Definition:

Publication 1738-UM001A-EN-P - February 2005

Preface 5

Related Products and

Documentation

The following table lists related ArmorPoint I/O products and

documentation:

Subnet 1738-ADNX only.

The Subnet DeviceNet network is defined as the DeviceNet

link that provides the expansion of the PointBus to let the

1738-ADNX use its lower connector to add an additional 500

meters and up to 63 nodes. These nodes will be bridged

through the 1738-ADNX up to the primary network. Note that

backplane modules are also part of the Subnet.

Term: Definition:

Description Cat. No. Publication

ArmorPoint 24V dc Output Modules Installation Instructions 1738-OB2E, -OB2EP, -OB4E, -OV4E, -OB8E 1738-IN001

ArmorPoint 24V dc Input Modules Installation Instructions 1738-IB2, IB4, -IV4, -IB8, -IV8 1738-IN002

ArmorPoint 24V dc Analog Input Modules Installation Instructions 1738-IE2C, -IE2V 1738-IN003

ArmorPoint 24V dc Analog Output Modules Installation Instructions 1738-OE2C, -OE2V 1738-IN004

ArmorPoint RTD and Thermocouple Modules Installation Instructions 1738-IR2, -IT2I 1738-IN005

ArmorPoint AC Input Modules Installation Instructions 1738-IA2M12AC3, -IA2M12AC4 1738-IN006

ArmorPoint AC Output Module Installation Instructions 1738-OA2M12AC3 1738-IN007

ArmorPoint Relay Output Modules Installation Instructions 1738-OW4M12, -OW4M12AC 1738-IN008

ArmorPoint RS232 ASCII Module Installation Instructions 1738-232ASCM12 1738-IN009

ArmorPoint RS485 ASCII Module Installation Instructions 1738-485ASCM12 1738-IN010

ArmorPoint 24V dc VHSC Module Installation Instructions 1738-VHSC24M23 1738-IN011

ArmorPoint 5V dc Incremental Encoder Module Installation Instructions 1738-IJM23 1738-IN012

ArmorPoint SSI Module Installation Instructions 1738-SSIM23 1738-IN013

ArmorPoint DeviceNet Adapters Installation Instructions 1738-ADN12, -ADN18, -ADN18P, -ADNX 1738-IN014

ArmorPoint PROFIBUS Adapter Installation Instructions 1738-APB 1738-IN015

ArmorPoint PROFIBUS Adapter User Manual 1738-UM002

ArmorPoint ControlNet Adapter Installation Instructions 1738-ACNR 1738-IN016

ArmorPoint ControlNet Adapter User Manual 1738-UM003

ArmorPoint EtherNet/IP Adapter Installation Instructions 1738-AENT 1738-IN017

ArmorPoint EtherNet/IP Adapter User Manual 1738-UM004

ArmorPoint Extension Units Installation Instructions 1738-EXT1, -EXT3 1738-IN018

ArmorPoint Field Potential Distributor Installation Instructions 1738-FPD 1738-IN019

ArmorPoint I/O 24V dc Expansion Power Supply Installation Instructions 1738-EP24DC 1738-IN020

DeviceNet Media Design & Installation Guide N/A DNET-UM072

Industrial Automation Wiring and Grounding Installation Instructions N/A 1770-4.1

Publication 1738-UM001A-EN-P - February 2005

Preface 6

If you need more information on these products, contact your local

Rockwell Automation/Allen-Bradley distributor, integrator or sales

office for assistance. For more information on the documentation,

refer to the Allen-Bradley Publication Index, publication SD499.

Guidelines for Using

Your Adapter

Remember the following operational guidelines when using your

ArmorPoint DeviceNet adapter.

•Do not leave spaces in the I/O. Instead, install all ArmorPoint

I/O modules adjacent to each other.

•Populate every position on the mounting base.

•ArmorPoint does not support removal and insertion under

power (RIUP). When an I/O module is removed, the IP67 seal is

broken and the backplane bus is interrupted.

•Use Allen-Bradley terminal markers to identify your ArmorPoint

I/O modules.

For more information on the Allen-Bradley terminal marking

kits, see the documents list on page Preface-5.

Conventions Used In

This Manual

The following conventions are used throughout this manual:

•bullet lists (such as this one) provide information, not

procedural steps

•numbered lists provide sequential steps

•text written like this identifies screen, menu, toolbar names, field

names, buttons, and check boxes on screens

•a menu item in this format File>Save identifies the submenu item

after the caret (>) that is accessed from the main menu (name

before the caret)

•pictures of symbols and/or screens represent the actual symbols

you see or the screens you use

iPublication 1738-UM001A-EN-P - February 2005

Table Of Contents

Chapter 1

Install the ArmorPoint

DeviceNet Adapters

Mount the Adapter and I/O Base. . . . . . . . . . . . . . . . . . . . 1-1

Set the Node Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Wire the DeviceNet Adapters. . . . . . . . . . . . . . . . . . . . . . . 1-3

1738-ADN12 and 1738-ADNX. . . . . . . . . . . . . . . . . . . . 1-3

1738-ADN18 and 1738-ADN18P . . . . . . . . . . . . . . . . . . 1-3

1738 ArmorPoint DeviceNet Auxiliary Power . . . . . . . . 1-4

Chapter Summary and What’s Next . . . . . . . . . . . . . . . . . . 1-4

Chapter 2

What Is the ArmorPoint

DeviceNet Adapter?

Use the Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Set Subnet/Backplane Baudrate . . . . . . . . . . . . . . . . . . 2-3

Set Subnet/Backplane I/O Module Addresses . . . . . . . . 2-3

Configure the Subnet I/O. . . . . . . . . . . . . . . . . . . . . . . 2-3

Configure the Primary DeviceNet Network . . . . . . . . . . 2-4

Remove and Reinsert Modules on the Backplane . . . . . 2-5

Understand the DeviceNet Network and Subnet. . . . . . . . . 2-6

DeviceNet Network . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Backplane/Subnet Network . . . . . . . . . . . . . . . . . . . . . 2-7

Adapter Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Communicate Through the Adapter . . . . . . . . . . . . . . . . . . 2-18

Map the Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Overview of the Communication Process . . . . . . . . . . . 2-19

Image Table Mapping . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Communicate With I/O Modules . . . . . . . . . . . . . . . . . . . . 2-23

Use Diagnostic Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

Chapter Summary and What’s Next . . . . . . . . . . . . . . . . . . 2-26

Chapter 3

Use Auto Start Mode

Why Use Auto Start Mode? . . . . . . . . . . . . . . . . . . . . . . . . 3-2

What Does Auto Start Mode Do?. . . . . . . . . . . . . . . . . . 3-2

How Is I/O Data Mapped Using Auto Start Mode?. . . . . 3-3

Requirement To Using Auto Start Mode . . . . . . . . . . . . 3-4

Install the I/O Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Remove the Module From the Mounting Base. . . . . . . . 3-5

Use RSNetWorx for DeviceNet. . . . . . . . . . . . . . . . . . . . . . 3-5

Begin Auto Start Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Use Custom Configuration. . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Chapter Summary and What’s Next . . . . . . . . . . . . . . . . . . 3-10

Publication 1738-UM001A-EN-P - February 2005

Chapter 4

Configure the DeviceNet

Scanner Subnet

Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Add the Scanner To Your Network. . . . . . . . . . . . . . . . 4-2

Add I/O Modules To Your Network . . . . . . . . . . . . . . . 4-3

Set the Scanner’s Parameters. . . . . . . . . . . . . . . . . . . . . 4-3

Go On Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Chapter Summary and What’s Next . . . . . . . . . . . . . . . . . . 4-8

Chapter 5

Add the ArmorPoint DeviceNet

Adapter to the DeviceNet

Scanner’s Scanlist

Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Add the Adapter to Your Network . . . . . . . . . . . . . . . . 5-2

Set the Adapter’s Parameters. . . . . . . . . . . . . . . . . . . . . 5-3

Go On Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Chapter Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Chapter 6

Troubleshoot the ArmorPoint

DeviceNet Adapter

Use the Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Guidelines for Using Your Adapter . . . . . . . . . . . . . . . . . . 6-3

Chapter Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Appendix A

Specifications

Appendix B

Quick Start For the 1738-ADNX

What’s In This Appendix? . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Assumptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Review of the 1738-ADNX Rules and the MACID Parameter B-9

Review of Auto Start Mode. . . . . . . . . . . . . . . . . . . . . B-11

Browse the Subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-15

Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . B-19

Navigate Between Networks. . . . . . . . . . . . . . . . . . . . B-24

Appendix C

Rules and Guidelines For

the 1738-ADNX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Adapter Handbücher

Allen-Bradley

Allen-Bradley PowerFlex 22-COMM-B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 20-COMM-D Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-AENT Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact I/O 1769-ADN DeviceNet Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-BNC2TNC Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorPoint DeviceNet A Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet Ex 1797-ACNR15 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140MG Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794ASB Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 525 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711R-APK10 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G-G-DRA Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O ControlNet 1734-ACNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 20-COMM-M Modbus/TCP Adapter Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O EtherNet/IP 1734-AENT Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O ControlNet 1734-ACNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley PLC-5 series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-AENTR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2071-TBMF Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2100-ENET Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung