Allen-Bradley PLC-5 series Bedienungsanleitung

User

Manual

PLC-5 Ethernet

Interface Module

(Cat. No. 1785-ENET)

Allen-Bradley

Because of the variety of uses for the products described in this

publication, those responsible for the application and use of this

control equipment must satisfy themselves that all necessary steps

have been taken to assure that each application and use meets all

performance and safety requirements, including any applicable laws,

regulations, codes and standards.

The illustrations, charts, sample programs and layout examples

shown in this guide are intended solely for purposes of example.

Since there are many variables and requirements associated with any

particular installation, Allen-Bradley does not assume responsibility

or liability (to include intellectual property liability) for actual use

based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the

Application, Installation, and Maintenance of Solid-State Control

(available from your local Allen-Bradley office), describes some

important differences between solid-state equipment and

electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in

whole or in part, without written permission of Allen-Bradley

Company, Inc., is prohibited.

Throughout this manual we use notes to make you aware of safety

considerations:

!ATTENTION: Identifies information about practices

or circumstances that can lead to personal injury or

death, property damage or economic loss.

Attention statements help you to:

•identify a hazard

•avoid the hazard

•recognize the consequences

Important: Identifies information that is critical for successful

application and understanding of the product.

ControlNet is a trademark; PLC is a registered trademark of Allen-Bradley Company, Inc.

Important User

Information

Publication

1785-6.5.19–June 1996

Chapter 1

Installing

and Configuring the Interface Module

1–2

. . . . . . . . . . . . . . .

What Y

ou Have Done

1–7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

What’s Next

1–7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2

Using

This Chapter

2–1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Before Y

ou Begin

2–2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Necessary

Equipment

2–3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preventing Electrostatic Discharge Damage (ESD)

2–3

. . . . . . . . . . . . .

Complying

with European Union Directives

2–4

. . . . . . . . . . . . . . . . . .

EMC Directive

2–4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Low V

oltage Directive

2–4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing

the Interface Module

2–5

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Attach

the Connector Header to the Processor

2–5

. . . . . . . . . . . . . .

Connect

the Interface Module to the Processor

2–6

. . . . . . . . . . . . .

Install

the Processor/Interface Module into the Chassis

2–7

. . . . . . . .

Removing

the Interface Module

2–8

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 3

Using

This Chapter

3–1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Before Y

ou Begin

3–1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring

Channel 3A

3–2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Designate

Channel 3A to Support the Interface Module

3–2

. . . . . . . .

Specify

Ethernet-specific Information

3–3

. . . . . . . . . . . . . . . . . . . . .

Manually

Entering Module Configuration Information

3–3

. . . . . . .

Dynamically

Supplying Configuration Information using BOOTP

3–5

Using the BOOTP Servers on the Utility Disk

3–6

. . . . . . . . . . . . . . . . .

Install the DOS/Windows BOOTP server disk

3–6

. . . . . . . . . . . . . . .

Edit

the DOS/Windows BOOTP Configuration File

3–7

. . . . . . . . . . .

Run

the Boot Server Utility

3–9

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Running the DOS-Based Utility

3–9

. . . . . . . . . . . . . . . . . . . . . . .

Running

the Windows-Based Utility

3–10

. . . . . . . . . . . . . . . . . . . .

Table of Contents

Quick

tart

Installin

the

Interface

ule

Confi

urin

the

Interface Module for

thernet

Communication

Table of Contentsii

Publication

1785-6.5.19–June 1996

Chapter 4

Using

This Chapter

4–1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Applying Power to the Chassis

4–1

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Monitoring the LEDs

4–1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Establishing

an Ethernet Connection

4–4

. . . . . . . . . . . . . . . . . . . . . . .

Monitoring

Ethernet Status Data

4–5

. . . . . . . . . . . . . . . . . . . . . . . . . .

Using

the Message Instruction

4–7

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Interpreting Error Codes

4–9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SNMP

Support

4–10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Saving

and Restoring Programs

4–10

. . . . . . . . . . . . . . . . . . . . . . . . . .

Appendix A

Appendix B

Appendix C

Appendix D

Communicatin

the

Interface Module

Module Specifications

Peformance Data

SNMP Management

Information Base (MIB) II

Data Groups

Status LED Error Codes

Preface

Publication

1785-6.5.19–June 1996

Preface

Read this preface to familiarize yourself with the rest of the manual.

This preface covers the following topics:

•who should use this manual

•the purpose of this manual

•Allen-Bradley support

Use this manual if you are responsible for designing, installing,

programming, or troubleshooting control systems that use

Allen-Bradley programmable controllers or interface modules.

You should have a basic understanding of PLC-5 programmable

controller products and the following Ethernet-related topics:

•TCP/IP protocol

•Internet addressing

If you do not have an understanding of these areas, contact your

local Allen-Bradley representative for information on available

training courses before using this product.

This manual:

•tells you what equipment you must provide for installing the

PLC-5 Ethernet Interface Module

•helps you install and configure the interface module

•helps you connect to an Ethernet link and

communicate via the interface module

Who Should Use this

Manual

Purpose of this Manual

PrefaceP–2

Publication

1785-6.5.19–June 1996

Contents of this Manual

Chapter Title Contents

Preface Describes the purpose, background, and scope of

this manual. Also specifies the audience for whom

this manual is intended.

1Quick Start Provides brief installation and configuration

procedures for the advanced user.

2Installing the Interface Module

Explains and illustrates how to install and remove

the interface module into and from the 1771 I/O

chassis. Also specifies compliance with European

Union Directives.

3Configuring the Interface Module

for Ethernet Communication

Provides instructions for:

•configuring

channel 3A to support the interface module

•

assigning an IP address to the module

•using the BOOTP servers on the utility disk

4Communicating Via the

Interface Module

Describes how to establish an Ethernet connection

and monitor status data. Also specifies how to use

the MSG instruction over the Ethernet link.

Appendix A Specifications Provides physical, electrical, and environmental

specifications for the interface module.

Appendix B Performance Data Provides measured performance data for the

interface module.

Appendix C SNMP Management Information

Base (MIB) II Data Groups Describes the SNMP Management Information

Base (MIB) II Data Groups.

Appemdix D Status LED Error Codes Describes the status LED error codes.

Related Documentation

For additional information regarding Allen-Bradley programmable

controllers and related products, see the Enhanced and Ethernet

PLC-5 Programmable Controllers User Manual, publication

1785-6.5.12.

To obtain a copy, contact your local Allen-Bradley office or

distributor.

Preface P–3

Publication

1785-6.5.19–June 1996

Allen-Bradley offers support services worldwide, with over 75

Sales/Support Offices, 512 authorized Distributors and 260

authorized Systems Integrators located throughout the United States

alone, plus Allen-Bradley representatives in every major country in

the world.

Local Product Support

Contact your local Allen-Bradley representative for:

•sales and order support

•product technical training

•warranty support

•support service agreements

Technical Product Assistance

If you need technical assistance, call your local Allen-Bradley

representative.

Your Questions or Comments on this Manual

If you find a problem with this manual, please notify us of it on the

enclosed Publication Problem Report.

If you have any suggestions for how this manual could be made

more useful to you, please contact us at the address below:

Technical Communication

Allen-Bradley Comapny

1 Allen-Bradley Drive

Mayfield Heights, Ohio 44124

Allen-Bradley Support

Chapter 1

Publication

1795-6.5.19–June 1996

Quick Start 1

This chapter can help you get started quickly using the PLC-5

Ethernet Interface Module. We base the procedures here on the

assumption that you have an understanding of:

•PLC-5 products

•TCP/IP protocol

•Internet addressing

Because this is a quick start guide for experienced users, this chapter

does not contain detailed explanations about the procedures listed. It

does, however, reference other chapters in this book where you can

get more information.

If you have any questions or are unfamiliar with the terms used or

concepts presented in the procedural steps, always read the

referenced chapters and other recommended documentation before

trying to apply the information.

This chapter:

•tells you what equipment you must provide for installing the

Ethernet interface module

•helps you install and configure the module

•helps you connect to an Ethernet link and

communicate via the interface module

20611–M

Status

indicator

External

transceiver

fuse

ransmit

indicator

Channel 3A:

15-pin AUI

connector port

1–2

Quick Start 1

Publication

1795-6.5.19–June 1996

1. Check

the contents of your shipment.

✔

Quantity Description

1PLC-5 Ethernet Interface Module (1785-ENET)

Connector it containing 1 PLC-5 58-pin connector header

Connector

it containing 1 PLC-5 58-pin connector header

1Industrial Automation Wiring and Grounding Guidelines,

publication 1770-4.1

1PLC-5 Ethernet Interface Module User Manual,

publication 1785-6.5.19

1BOOTP Utility Diskette

2. Locate

and have ready all equipment and tools necessary for installation.

✔

I/O Chassis

(1771-A1B/B, -A2B/B, -A3/B or -A4B/B)

Any external or internal

Allen-Bradley power supply

ESD

Grounding

Wrist Strap

phillips

screwdriver

PLC-5 Processor

Supported processors and current firmware

(see page 2-1)

Installing and Configuring

the Interface Module

1–3

Quick Start 1

Publication

1795-6.5.19–June 1996

3. Attach

the connector header to the processor

Reference

Chapter 2

Installing the

Interface Module

Important: Make sure you carefully align the pins and holes before you press the connector header into

the processor. If you improperly align them, you will bend the connector header pins when

you press them together. Do not use excessive force on the connector header when seating it

into the processor. You do not need to key the connector.

4. Use

the captive screws to connect the interface module to the processor

Reference

Chapter 2

Installing the

Interface Module

Front of the PLC-5 processor

Front of the interface module

Installed connector

header 20597–M

19379

Attach the interface

module to this end.

connector

header

Push the exposed pins

into the holes on the

PLC-5 processor.

!Wear a grounding wrist

strap to guard against ESD.

Andere Handbücher für PLC-5 series

Inhaltsverzeichnis

Andere Allen-Bradley Adapter Handbücher

Allen-Bradley

Allen-Bradley 2711P-RAAT7 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPA/B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 22-COMM-B Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O ControlNet 1734-ACNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 22-COMM-E FRN 1.xxx Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2711R-APK10 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 5069-AENTR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX 5000 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 525 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2100-ENET Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O ControlNet 1734-ACNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-AENTR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 20-COMM-M Modbus/TCP Adapter Bedienungsanleitung

Allen-Bradley

Allen-Bradley Rockwell Automation 1734-AENT Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-AENTRK Bedienungsanleitung

Allen-Bradley

Allen-Bradley Compact I/O 1769-ADN DeviceNet Bedienungsanleitung

Allen-Bradley

Allen-Bradley 2100-ENET Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorPoint DeviceNet 1738-ADN12 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794ASB Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 140G Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O PROFIBUS 1794-APBDPV1 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung