Allen-Bradley 1771-OBD Bedienungsanleitung

Publication 1771-IN054C-EN-P - November 2006

Installation Instructions

dc (10…60V) Output Module

Catalog Number 1771-OBD Series C

About This Publication

Use this document as a guide when installing the 1771-OBD series C output module.

Topic Page

About This Publication 1

Important User Information 2

Before You Begin 4

Key the Backplane 5

Install the Module 6

Interpreting the LED Indicators 11

Replace the Fuse 12

Hazardous Location Approvals 13

Specifications 15

8dc (10…60V) Output Module

Publication 1771-IN054C-EN-P - November 2006

Connection Diagram

You must supply dc at terminals A through D on the wiring arm. You need four dc

connections to accommodate the total required surge rating on the module without

overstressing any single connection on the field wiring arm. Jumper all dc connections

together to prevent module damage. Connect terminal E to dc common.

User

dc Supply

dc Output

Device

Sourcing Configuration

Actual wiring runs in this direction.

The output device is

sinking current from

the module.

See applicable codes and laws.

+dc

Output 00

Output 01

Output 02

Output 03

Output 04

Output 05

Output 06

Output 07

Output 10

Output 11

Output 12

Output 13

Output 14

Output 15

Output 16

Output 17

-dc

11915

dc (10…60V) Output Module 9

Publication 1771-IN054C-EN-P - November 2006

Refer to Driving an Input with an Output Module on page for direct connection to a

1771-ICD input module.

ATTENTION Observe proper polarity, as indicated in the connection diagram on page 10 with dc

power connections. Reverse polarity, or application of ac voltage, could damage the

module.

IMPORTANT You can use a dc (10…60V) output module (771-OBD series C) to directly drive

terminals on the following modules:

•dc (5…30V) input module (1771-IQ)

•dc (10…30V) input module (1771-IBD, 1771-IBN)

•dc (20…60V) input module (1771-ICD)

•dc (12…24V) input module (1771-IB)

•dc (24V) input module (1771-IQ16)

•dc (48V) input module (1771-IC)

IMPORTANT Use the same dc supply to power both modules to make sure that ground is at the same

potential.

10 dc (10…60V) Output Module

Publication 1771-IN054C-EN-P - November 2006

Driving an Input with an Output Module

Actual wiring runs in this direction.

See applicable codes and laws.

+dc

Output 00

Output 01

Output 02

Output 03

Output 04

Output 05

Output 06

Output 07

Output 10

Output 11

Output 12

Output 13

Output 14

Output 15

Output 16

Output 17

-dc

Input 00

Input 01

Input 02

Input 03

Input 04

Input 05

Input 06

Input 07

Input 10

Input 11

Input 12

Input 13

Input 14

Input 15

Input 16

Input 17

dc Common

22…60Vdc

dc (10…60V) Output Module dc (20…60V) Input Module

Not Used

11916

1771-ICD1771-OBD

dc (10…60V) Output Module 15

Publication 1771-IN054C-EN-P - November 2006

Specifications

dc (10…60V) Output Module, 1771-OBD Series C

Attribute Value

Outputs per module 16 nonisolated

Module location 1771-A1B through 1771-A4B I/O chassis (Do not use this module

with 1771-A4 I/O chassis)

User supply voltage 10…60V dc

Voltage, on-state output, nom 48V dc

Current rating (see Derating Curve) 2 A per output resistive, not to exceed 8 A per module

0.2 A per output pilot duty

Surge current, max 4 A per output for 10 ms, repeatable every 2 s

25 A per output for 10 ms, repeatable every 2 s

Load current, min 2.5 mA

On-state voltage drop (at rated

current), max

1.5V dc

Off-state leakage current, max 0.5 mA

Output signal delay, max

Off to on

On to off

0.1 ms

0.2 ms

Power dissipation, max 15.6 W

Thermal dissipation, max 53.3 BTU/hr

Isolation voltage (continuous-voltage

withstand rating)

60V (continuous), Basic Insulation Type

Tested at 1000V ac for 60 s, I/O to system

Backplane current, max 400 mA @ 5V dc

Conductors wire size

Category(1)

(1) Use this conductor category information for planning conductor routing. Refer to Industrial Automation Wiring and

Grounding Guidelines, publication 1770-4.1.

0.34…2.5 mm2(22…14 AWG) solid or stranded copper wire rated

at 120 °C (248 °F) or higher

1.2 mm (3/64 in.) insulation max

2 - on signal ports

Temperature code, IEC T3

Temperature code, North America T3C

Field wiring arm 1771-WH

1771-WHF (3 A fused)(2)

1771-WHFB (1.5 A fused)(2)

(2) Not suitable for Class I Division 2 Groups A, B, C, and D Hazardous Locations.

Field wiring arm screw torque 1.0 Nm (9 lb-in)

Keying Between 10 and 12

Between 22 and 24

16 dc (10…60V) Output Module

Publication 1771-IN054C-EN-P - November 2006

Environmental Specifications

Attribute Value

Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),

IEC 60068-2-2 (Test Bd, Operating Dry Heat),

IEC 60068-2-14 (Test Nb, Operating Thermal Shock):

0…60 °C (32…140 °F)

Temperature, storage IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),

IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),

IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):

–40…85 °C (–40…185 °F)

Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):

5…95% noncondensing

Vibration IEC 60068-2-6 (Test Fc, Operating):

2 g @ 10…500 Hz

Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):

30 g

Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):

50 g

ESD immunity IEC 61000-4-2:

4 kV indirect contact discharges

Radiated RF immunity IEC 61000-4-3:

10 V/m with 1 kHz sine-wave 80% AM from 30…1000 MHz

EFT/B immunity IEC 61000-4-4:

±1 kV at 5 kHz on signal ports

Surge transient immunity IEC 61000-4-5:

±1 kV line-line (DM) and ±2 kV line-earth (CM) on signal ports

Conducted RF immunity IEC 61000-4-6:

10V rms with 1 kHz sine-wave 80% AM from 150 kHz…30 MHz

Emissions CISPR 11:

Group 1, Class A (with appropriate enclosure)

Enclosure type rating None (open style)

dc (10…60V) Output Module 17

Publication 1771-IN054C-EN-P - November 2006

Certifications

Certification (when product is

marked)(1)

(1) See the Product Certification link at www.ab.com for Declarations of Conformity, certificates, and other certification details.

Value

UL UL Listed Industrial Control Equipment. See UL File E65584

CSA CSA certified Process Control Equipment. See CSA file LR54689C.

CSA CSA certified Process Control Equipment for Class I, Division 2,

Groups A, B, C and D Hazardous locations. See CSA file LR69960C.

EEx European Union 94/9/EC Directive, compliant with:

EN 60079-15; Potentially Explosive Atmospheres, Protection n (zone 2)

CE European Union 89/336/EEC EMC Directive, compliant with:

EN 61000-6-4; Industrial Emissions

EN 50082-2; Industrial Immunity

EN 61326; Meas./Control/Lab., Industrial Requirements

EN 61000-6-2; Industrial Immunity

C-Tick Australian Radiocommunications Act compliant with

AS/NZS CISPR 11, Industrial Emissions

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley Logix5000 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLBRED20 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OE8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-OB16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet ControlLogix 1756 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-16CFGM12M12LDR Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFRL/B Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OF6CI Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA8D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OD Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley ArmorBlock 1792 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE8 Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley CAB6-HA 2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix SynchLink 1756-SYNCH Bedienungsanleitung

Allen-Bradley

Allen-Bradley SLC 500 DeviceNet Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung