Allen-Bradley POINT I/O 1734-4IOL Bedienungsanleitung

Installation Instructions

Original Instructions

POINT I/O 4 Channel IO-Link Master Module

Catalog Number

1734-4IOL

Topic Page

Important User Information 2

Environment and Enclosure 3

Prevent Electrostatic Discharge 4

Special Conditions for Safe Use 5

About the Module 6

Install the Mounting Base 9

Install the Module 9

Install the Removable Terminal Block 11

Remove a Mounting Base 13

Wire the Module 14

Communicate with the Module 16

Interpret Status Indicators 18

Specifications 20

2Rockwell Automation Publication 1734-IN043B-EN-E - January 2019

POINT I/O 4 Channel IO-Link Master Module

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid-state Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid-

state equipment and hard-wired electromechanical devices. Because of this difference, and also because of

the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements that are associated with any particular installation, Rockwell

Automation, Inc. cannot assume responsibility or liability for actual use based on the examples

and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of

Rockwell Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you identify a

hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or motor)

to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to

alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

Rockwell Automation Publication 1734-IN043B-EN-E - January 2019 3

POINT I/O 4 Channel IO-Link Master Module

Environment and Enclosure

ATTENTION:

This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in EN/IEC 60664-1),

at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not

provide adequate protection to radio communication services in such environments.

This equipment is supplied as open-type equipment for indoor use. It must be

mounted within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to

prevent personal injury resulting from accessibility to live parts. The enclosure

must have suitable flame-retardant properties to prevent or minimize the spread

of flame, complying with a flame spread rating of 5V A or be approved for the

application if nonmetallic. The interior of the enclosure must be accessible only by

the use of a tool. Subsequent sections of this publication may contain more

information regarding specific enclosure type ratings that are required to comply

with certain product safety certifications.

In addition to this publication, see the following:

• Industrial AutomationWiring and Grounding Guidelines,

publication 1770-4.1, for additional installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the

degrees of protection provided by enclosures.

ATTENTION: Read this document and the documents listed in the Additional

Resources section about installation, configuration, and operation of this

equipment before you install, configure, operate, or maintain this product. Users

are required to familiarize themselves with installation and wiring instructions in

addition to requirements of all applicable codes, laws, and standards.

Installation, adjustments, putting into service, use, assembly, disassembly, and

maintenance are required to be carried out by suitably trained personnel in

accordance with applicable code of practice. In case of malfunction or damage, no

attempts at repair should be made. The module should be returned to the

manufacturer for repair. Do not dismantle the module.

4Rockwell Automation Publication 1734-IN043B-EN-E - January 2019

POINT I/O 4 Channel IO-Link Master Module

Prevent Electrostatic Discharge

Electrical Safety Considerations

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION:

• This equipment is certified for use only within the surrounding air temperature

range of -20…+55 °C (-4…+131 °F). The equipment must not be used

outside of this range.

• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any

cleaning agents.

At the end of its life, this equipment should be collected separately from any

unsorted municipal waste.

Rockwell Automation Publication 1734-IN043B-EN-E - January 2019 5

POINT I/O 4 Channel IO-Link Master Module

Special Conditions for Safe Use

ATTENTION:

• This product is grounded through the DIN rail to chassis ground. Use zinc

plated chromate-passivated steel DIN rail to assure proper grounding. The use

of other DIN rail materials (for example, aluminum or plastic) that can corrode,

oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail

properly. Refer to Industrial AutomationWiring and Grounding Guidelines,

publication 1770-4.1, for more information.

• Do not remove or replace an Adapter Module while power is applied.

Interruption of the backplane can result in unintentional operation or

machine motion.

• Do not discard the end cap. Use this end cap to cover the exposed

interconnections on the last mounting base on the DIN rail. Failure to do so

could result in equipment damage or injury from electric shock.

• If this equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

ATTENTION: Do not wire more than two conductors on any single terminal.

6Rockwell Automation Publication 1734-IN043B-EN-E - January 2019

POINT I/O 4 Channel IO-Link Master Module

About the Module

The POINT I/O 4 Channel IO-Link Master Module provides four channels

that can be individually configured as IO-Link master or as a standard digital I/

O module. The IO-Link channel master module can be configured to fit any

IO-Link and/or discrete application.

In IO-Link mode, the module supports four channels for IO-Link master

communication with IO-Link compatible devices. In standard digital I/O mode,

the module supports four channels of digital input or output. Standard digital

input channels support IEC61131-2 type 1 input. Channels can also be disabled

if not in use.

You must use this module with the 1734-AENT or 1734-AENTR, Series B

EtherNet/IP adapters, firmware revision 5.012 or later, and RSLogix 5000®/

Studio 5000® software, version 20 or later. Use this diagram to identify the

external features of the module.

Rockwell Automation Publication 1734-IN043B-EN-E - January 2019 7

POINT I/O 4 Channel IO-Link Master Module

POINT I/O 4 Channel IO-Link Master Module with 1734-TB, 1734-TBS, 1734-TB3, or 1734-

TB3S Wiring Base Assembly

Description Description

1 Module locking mechanism 6 Terminal base

2 Slide-in writable label 7 Interlocking side pieces

3 Insertable I/O module 8 Mechanical keying (orange)

4 Removable terminal block (RTB) handle 9 DIN rail locking screw (orange)

5 Removable terminal block 10 Module wiring diagram

Analog

Voltage

Output

Module

Status

Network

Status

NODE:

24V DC

SIO

LINK

Module

Status

Network

Status

1734-4IOL

NODE:

The 1734-TB, 1734-TBS, 1734-TB3, or 1734-TB3S

wiring base assembly consists of a 1734-MB

mounting base and a 1734-RTB or 1734-RTBS

removable terminal block. 46012

8Rockwell Automation Publication 1734-IN043B-EN-E - January 2019

POINT I/O 4 Channel IO-Link Master Module

POINT I/O 4 Channel IO-Link Master Module with 1734-TOP, 1734-TOPS, 1734-TOP3, or

1734-TOP3S One-piece Terminal Base

Description Description

1 Module locking mechanism 6 Interlocking side pieces

2 Slide-in writable label 7 Mechanical keying (orange)

3 Insertable I/O module 8 DIN rail locking screw (orange)

4 Terminal block handle

9 Module wiring diagram

5 One-piece terminal base

24V DC

SIO

LINK

Module

Status

Network

Status

1734-4IOL

NODE:

46013

Rockwell Automation Publication 1734-IN043B-EN-E - January 2019 9

POINT I/O 4 Channel IO-Link Master Module

Install the Mounting Base

To install the mounting base on the DIN rail, proceed as follows:

1. Position the mounting base vertically above the installed units (adapter,

power supply, or existing module).

2. Slide the mounting base down allowing the interlocking side pieces to

engage the adjacent module or adapter.

3. Press firmly to seat the mounting base on the DIN rail. The mounting

base snaps into place. Be sure that the orange DIN rail locking screw is in

the horizontal position and that it has engaged the DIN rail.

Install the Module

The module can be installed before or after base installation. Make sure that the

mounting base is correctly keyed before installing the module into the mounting

Slide the mounting base until the

interlocking side pieces engage the

adjacent module or adapter.

46014

10 Rockwell Automation Publication 1734-IN043B-EN-E - January 2019

POINT I/O 4 Channel IO-Link Master Module

base. In addition, make sure that the mounting base locking screw is positioned

horizontal referenced to the base.

1. Using a bladed screwdriver, rotate the keyswitch on the mounting base

clockwise until the number required for the type of module being

installed aligns with the notch in the base.

2. Make certain the DIN rail locking screw is in the horizontal position.

You cannot insert the module if the locking mechanism is unlocked.

3. Insert the module straight down into the mounting base.

Turn the keyswitch to align

the number with the

notch. Notch position 2 is

shown.

Be sure the DIN rail locking

screw is in the horizontal

position.

1734-TB Base

44229

Turn the keyswitch to

align the number with

the notch. Notch

position 2 is shown.

Be sure the DIN rail locking

screw is in the horizontal

position.

1734-TOP Base

44228

Andere Handbücher für POINT I/O 1734-4IOL

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley 1784-KT2/C Installations- und Benutzerhandbuch

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1203-GD2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-12X4M12QCDR Handbuch

Allen-Bradley

Allen-Bradley CENTERLINE 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 857-VPA3CG Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFS Bedienungsanleitung

Allen-Bradley

Allen-Bradley E300 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1769-OF8C Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1792-IB16 Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IF4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA8D Bedienungsanleitung

Allen-Bradley

Allen-Bradley Micro800 2080-MEMBAK-RTC2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OBN Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-DHRIO Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IXHR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD006 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1606-XLS960BUFFER Bedienungsanleitung

Allen-Bradley

Allen-Bradley D Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD007 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Bulletin 160 DeviceNet Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung