Allen-Bradley 1771-ODD Bedienungsanleitung
1
AC (120V) Isolated Output Module,
16 Outputs
Cat. No. 1771ODD
Installation Instructions
This document provides information on:
important pre-installation considerations
power supply requirements
installing the module
installing and connecting the wiring
replacing the fuse
using the module indicators for troubleshooting
module specifications
An output from this module can drive an Allen-Bradley Size 5 motor
starter, provided its supply voltage does not drop below 92V ac. The
maximum load current the module can deliver is 2A per channel, not to
exceed 8A total per module.
Your module’s outputs can drive the following motor starter combinations:
16 size 3 motor starters (1 per output)
10 size 4 motor starters (1 per output)
7 size 5 motor starters (1 per output)
The switching device in the output circuit is a solid-state triac. There is a
small leakage current in the off state due to both triac and capacitive
characteristics. The maximum leakage current per output is 3mA at 138V
ac. Nominal leakage current is 1.5mA. The on-state voltage drop across
the output terminals will not exceed 1.5V ac at 2A.
To The Installer
Preinstallation
Considerations
AC (120V) Output Module
(Cat. No. 1771-ODD)
Installation Instructions
2
The 1771-ODD module is designed for a 10mA minimum current on each
output circuit. The total continuous current the module supports is 8A (2A
maximum per channel). If this rating is exceeded, the module overheats
and damage may occur.
Suppression
Surge suppression circuitry is provided for the output triacs in this module.
To suppress high-voltage transients from the ac line, a metal-oxide varistor
(MOV) is provided between each set of terminals on the module. In each
output circuit an RC network limits the magnitude of voltage transients
that may occur when a device is wired in parallel or series with hard
contacts.
Loads with inductive characteristics may require additional suppression
devices. The impedance characteristic of the load is the most important
factor in selecting a suppression device; thus no single suppression device
can be recommended for every possible load. See Table 1 for acceptable
suppression devices for typical loads.
Table 1
AllenBradley
Suppressors
AllenBradley Equipment Suppressor Catalog Number
Motor Starter Bulletin 509 599K041
Motor Starter Bulletin 709 1401N101
Relay Bulletin 700 Type N or P 700N5/700N9
Miscellaneous 700N242
1For
starters with 120V AC coils
2Bulletin
700N24 is a universal surge suppressor
. Y
ou can use it on electromagnetic devices with the limitation of
35 sealed V
A, 150V
.
The isolated output module is powered by the power supply connected to
the I/O chassis backplane. The module requires a maximum current of
420mA from the +5V dc output of this supply. Total the current
requirements of this module with the other modules in the I/O chassis to
avoid overloading the supply or the I/O chassis backplane.
Power Supply Requirements
AC (120V) Output Module
(Cat. No. 1771-ODD)
Installation Instructions
5
Figure 1
Connection
Diagram for the 1771ODD Isolated Output Module
Output 0
Output 1
Output 2
Output 3
Output 4
Output 5
Output 6
Output 7
Output 10
Output 11
Output 12
Output 13
Output 14
Output 15
Output 16
Output 17
L1
ac High
ac Low
L1 0
L1 1
L1 2
L1 3
L1 4
L1 5
L1 6
L1 7
L1 10
L1 11
L1 12
L1 13
L1 14
L1 15
L1 16
L1 17
Not Used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
120V ac
Supply
L1
L2
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
10944I
Output
Device
You can use an output of the 1771-ODD module to drive an input of a
120V ac input module (1771-IA, -IA2, -IAD,-ID) to indicate status of
turning on a motor starter, for example (Figure 2). Inputs configured with
the output module are not isolated from each other.
ATTENTION: Do not connect the 1771-ODD output channels
in series. Doing so can result in distortion of the output
waveform causing the output devices to chatter.
AC (120V) Output Module
(Cat. No. 1771-ODD)
Installation Instructions
6
Figure 2
Driving
an Input with an Output
Output 0
Output 1
Output 2
Output 3
Output 4
Output 5
Output 6
Output 7
Output 10
Output 11
Output 12
Output 13
Output 14
Output 15
Output 16
Output 17
L1
ac High
ac Low
L2
L1 0
L1 1
L1 2
L1 3
L1 4
L1 5
L1 6
L1 7
L1 10
L1 11
L1 12
L1 13
L1 14
L1 15
L1 16
L1 17
Not Used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
120V ac
Supply
L1 L2
Input 00
Input 01
Input 02
Input 03
Input 04
Input 05
Input 06
Input 07
Input 10
Input 11
Input 12
Input 13
Input 14
Input 15
Input 16
Input 17
AC (120V) Isolated Output Module
Cat. No. 1771ODD
AC/DC (120V) Input Module
Cat. No. 1771IAD
10945I
Each module output is individually fused. You can easily access the
module fuses by removing the front component-side cover. Follow the
procedure below.
ATTENTION: Remove power from the 1771 I/O chassis
backplane and wiring arm before removing or installing an I/O
module.
Failure to remove power from the backplane could cause
injury or equipment damage due to possible unexpected
operation.
Failure to remove power from the backplane or wiring arm
could cause module damage, degradation of performance, or
injury.
Replacing a Fuse
Specifications
AC (120V) Output Module
(Cat. No. 1771-ODD)
Installation Instructions
8
Outputs per Module 16
Module Location 1771A1B thru A4B or later I/O Chassis and 1771AM1, AM2
Voltage Rating 85 to 138V ac, 4763Hz
Current Rating (per channel) 10mA - 2A continuous (max)
20A surge for 100ms; repeatable once every 2 seconds
8A per module maximum
Power Rating 3 Watts per output (max) @ 2A
Onstate Voltage Drop (each output) 6.5V rms (max.) @ load current <65mA
1.5V rms (max.) @ load current >65mA
Signal Delay Times Off to On
On to Off
8.8msec @ 60Hz max.: 10.6msec @ 50Hz max
8.8msec @ 60Hz max.: 10.6msec @ 50Hz max
(zero cross switching)
Power Dissipation 14.2 Watts (max); 0.1 Watts (min)
Thermal Dissipation 48.5 BTU/hr (max); 0.4 BTU/hr (min)
Backplane Current 420mA maximum at 5.25V
Isolation Voltage 1500V channeltochannel
1500V to backplane
Maximum Cable Length 1000 ft (304.8 m)
Conductors Wire Size
Category
14 gauge stranded maximum
3/64 inch insulation maximum
11
Environmental Conditions
Operational Temperature
Storage Temperature
Relative Humidity
0oto 60oC (32oto 140oF)
40oto 85oC (40oto 185oF)
5 to 95% (without condensation)
Keying Between 4 and 6
Between 30 and 32
Field Wiring Arm Catalog Number 1771WN
Wiring Arm Screw Torque 7-9 poundinches
Fuses 3A 2AG SloBlo fuses (1 per output)
1
Refer to publication 17704.1, Programmable Controller Wiring and Grounding Guidelines
With major offices worldwide.
Algeria •
Argentina
•
Australia
•
Austria
•
Bahrain
•Belgium •Brazil •
Bulgaria
•
Canada
•Chile •
China, PRC
•
Colombia
•Costa Rica •
Croatia
•
Cyprus
•Czech
Republic
•
Denmark
•
Ecuador
•Egypt •El Salvador •Finland •France •
Germany
•
Greece
•
Guatemala
•
Honduras
•
Hong Kong
•
Hungary
•Iceland •
India
•
Indonesia
•
Israel
•Italy •Jamaica •
Japan
•
Jordan
•
Korea
•
Kuwait
•
Lebanon
•Malaysia •Mexico •
New Zealand
•
Norway
•Oman •Pakistan •
Peru
•Philippines
•
Poland
•
Portugal
•
Puerto Rico
•
Qatar
•
Romania
•
Russia-CIS
•
Saudi Arabia
•
Singapore
•Slovakia •Slovenia •
South Africa, Republic
•Spain •
Switzerland
•
T
aiwan
•Thailand •
The Netherlands
•T
urkey
•
United Arab Emirates
•
United Kingdom
•
United States
•
Uruguay
•V
enezuela
•Yugoslavia
W
orld Headquarters, AllenBradley
, 1201 South Second Street, Milwaukee, WI 53204 USA, T
el: (1) 414 3822000 Fax: (1) 414 3824444
AllenBradley has been helping its customers improve productivity and quality for 90 years.
AB designs, manufactures and supports a broad range of control and automation products
worldwide. They include logic processors, power and motion control devices, manmachine
interfaces and sensors. AllenBradley is a subsidiary of Rockwell International, one of the
world's leading technology companies.
Publication
17712.146 August 1991
Supersedes
publication 17712.146 March 1990
P/N
9551
1060
Copyright
1991 AllenBradley Co. Inc. Printed in USA
Inhaltsverzeichnis
Andere Allen-Bradley Steuereinheit Handbücher
Allen-Bradley
Allen-Bradley ArmorBlock 1732E Bedienungsanleitung
Allen-Bradley
Allen-Bradley MicroLogix 1762-IQ8 Bedienungsanleitung
Allen-Bradley
Allen-Bradley Logix5000 Series Bedienungsanleitung
Allen-Bradley
Allen-Bradley ControlLogix 1756-HYD02 Bedienungsanleitung
Allen-Bradley
Allen-Bradley XM-124 Bedienungsanleitung
Allen-Bradley
Allen-Bradley 1771-OD Installations- und Benutzerhandbuch
Allen-Bradley
Allen-Bradley SLC 5/02 Bedienungsanleitung
Allen-Bradley
Allen-Bradley FLEX I/O ControlNet 1794-ACN15 Bedienungsanleitung
Allen-Bradley
Allen-Bradley 1747-DTAM-E Bedienungsanleitung
Allen-Bradley
Allen-Bradley DeviceNet 1747-SDN/B Bedienungsanleitung
Allen-Bradley
Allen-Bradley 1756-M02AS Bedienungsanleitung
Allen-Bradley
Allen-Bradley 1771-KA2 Bedienungsanleitung
Allen-Bradley
Allen-Bradley ProcessLogix R300.1 Bedienungsanleitung
Allen-Bradley
Allen-Bradley Series B Bedienungsanleitung
Allen-Bradley
Allen-Bradley ControlLogix 1756-OX8I Bedienungsanleitung
Allen-Bradley
Allen-Bradley ControlNet ControlLogix 1756 Bedienungsanleitung
Allen-Bradley
Allen-Bradley ControlLogix 1756-ENET/B Bedienungsanleitung
Allen-Bradley
Allen-Bradley MicroLogix 1200 Bedienungsanleitung
Allen-Bradley
Allen-Bradley 1407-CGCM Bedienungsanleitung
Allen-Bradley
Allen-Bradley DH485/RS-232C Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
